Where is the fuse of Changan Eado located

1 Answers
VanAriana
07/30/25 12:00am
The fuse of Changan Eado is located in the fuse box within the engine compartment. Here are the relevant details: 1. Fuse failure: Generally, when a fuse is damaged, certain components of the vehicle may fail to operate normally. Therefore, if any part of the vehicle is malfunctioning, it should not be overlooked, especially the fuse, as it poses significant risks. 2. Changan Eado: With a price range of 74,900 to 106,900 RMB, the Changan Eado is quite competitive among its peers in the same class. The second-generation Eado is equipped with Changan Automobile's new inCall 3.0 intelligent vehicle connectivity system, ACC with Stop/Go full-speed adaptive cruise control, PAB warning-assisted braking, electronic body stability, and EPB electronic parking brake.
Was this review help?
18
5
Share
More Forum Discussions

What are the symptoms of a faulty BMW mass air flow sensor?

Symptoms may include increased engine fuel consumption, difficulty starting, and lack of engine acceleration power. The following are manifestations of faults in other parts of the vehicle: 1. Oxygen sensor: When the oxygen sensor fails, the ECU cannot obtain this information and thus cannot determine whether the injected fuel quantity is correct. An inappropriate air-fuel ratio will lead to reduced engine power and increased emission pollution. 2. Wheel speed sensor: Its main function is to collect the vehicle's speed to determine if there are signs of skidding. Therefore, a dedicated sensor is used to collect the wheel speed, typically installed on the hub of each wheel. Once the sensor is damaged, the ABS will fail. 3. Coolant temperature sensor: When the coolant temperature sensor fails, it often still displays the temperature signal from when the engine was hot during a cold start. The ECU cannot obtain the correct signal and can only supply the engine with a leaner mixture, making it difficult to start the engine when cold, accompanied by unstable idle operation and insufficient acceleration power. 4. Electronic throttle pedal position sensor: When the sensor fails, the ECU cannot detect the throttle position signal or obtain the correct position of the throttle pedal, resulting in poor engine acceleration or even the inability to accelerate. 5. Intake pressure sensor: As the name suggests, the intake pressure sensor detects a series of resistance and pressure changes according to different engine speed loads, converting them into voltage signals for the ECU to adjust fuel injection quantity and ignition timing. It is generally installed near the throttle body. If it fails, it can cause ignition difficulties, unstable idle, and lack of acceleration power.
7
0
Share

How to Use BMW Cruise Control?

The following introduces the usage of BMW cruise control: 1. The BMW cruise control switch is located on the left side of the steering wheel, with a total of three buttons. The I/0 button is used to turn the cruise control on or off. 2. Press the I/0 button to activate the function, and the central control screen will display that the cruise system is ready. 3. When driving reaches the desired speed, press the "SET" button to set the vehicle at the current cruising speed, and release the accelerator pedal to achieve cruise control. 4. To adjust the speed, you can use the lever. Pushing it up is to accelerate; pushing it down is to decelerate. 5. Press the brake pedal or clutch pedal to cancel the cruise system. Press the "RES" button to restore the original speed. Press the I/0 button again to cancel the cruise control.
13
0
Share

Why Can't a Motorcycle Engine Start?

Motorcycle engine failure to start can be caused by abnormal spark plug ignition, engine cylinder scoring, loss of magnetism in the motorcycle generator flywheel magnet, or poor contact between the ignition wire and the generator. When encountering difficulty starting or failure to start, it is essential to promptly troubleshoot to avoid unnecessary hazards. Abnormal Spark Plug Ignition: If the air gap between the magneto and the charging coil core is too large (the normal gap should not be less than 0.80mm), it can cause abnormalities when cutting the magnetic lines of force. Additionally, friction between the motorcycle flywheel and the charging coil core can cause a sharp rise in coil temperature, reducing insulation performance. Both scenarios can lead to abnormal ignition, potentially damaging the spark plug. Check if the spark plug has excessive carbon buildup and replace it promptly if necessary. Engine Cylinder Scoring: Cylinder scoring is a common issue during engine operation, leading to insufficient cylinder pressure, which prevents the motorcycle from starting normally or causes it to stall. After cylinder scoring occurs, professional repair is required, involving the replacement of critical components such as the cylinder liner, piston, and piston rings. Loss of Magnetism in Motorcycle Generator Flywheel Magnet: Most motorcycle engine generator magnetic fields consist of two or more sub-magnetic fields. However, when the magnet loses its magnetism, the magnetic field strength of each sub-field varies, resulting in asymmetric adjacent magnetic field strengths and significant current fluctuations. Professional repair shops should inspect and service the generator. Poor Contact Between Ignition Wire and Generator: Loose connections between the generator's output terminal and the ignition coil's input terminal can lead to poor contact, causing "jumpy" current fluctuations. Disordered current severely disrupts the spark plug's normal ignition function. Inspect whether the rubber sleeve connected to the ignition coil's secondary terminal and the protective sleeve of the terminal are sealed. Also, check for loose metal connectors inside. It is advisable to seek professional assistance.
6
4
Share

What Causes the Abnormal Noise When Braking After Rain?

The reasons for abnormal noise when braking after rain: 1. Mismatch between brake pads and brake discs; 2. Fine sand carried by water adhering to the brake discs or rust on the brake discs after rain; 3. Brake pads worn to the limit; 4. Faulty brake system; 5. Missing or damaged fixing screws of the brake discs. In rainy conditions, brake discs can develop rust due to physical phenomena. When brake discs are rusty, a noticeable noise can be heard during braking. Almost all vehicles in the industry using cast iron brake discs experience this phenomenon, but it does not affect braking performance. The friction blocks have a certain rust removal capability. When the vehicle is parked for a while and the rust on the brake discs is minimal, after driving a certain distance and applying the brakes a few times, the rust on the brake discs will be removed, and the abnormal braking noise will disappear.
13
3
Share

Why does the throttle of Changyong 1115 fluctuate?

The fluctuating throttle in Changyong 1115 could be due to a clogged fuel line. How to handle unstable motorcycle throttle: Check for blockages in the air filter and carburetor, ensure the fuel line is unobstructed, verify if the carburetor's air-fuel mixture is incorrect, inspect for air leaks in the intake pipe or valves, and examine the spark plug and ignition system components along with their wiring for any issues causing misfires. Also, check if the choke is closed, whether the carburetor needs cleaning, and if the fuel delivery system requires servicing. The importance of motorcycle throttle control: During startup; Starting requires sufficient torque, which varies by vehicle type and displacement. Some bikes have low torque at low RPMs, requiring gradual clutch release while applying throttle, while others may have enough torque at idle to start without throttle input—here, clutch control is key. During deceleration; Braking isn't always necessary—smoothly rolling off the throttle while downshifting can effectively reduce speed, though emergency situations demand coordinated brake and throttle use. In corners; When entering a curve, the bike leans to counter centrifugal force, making balance precarious. Braking becomes a harsh control method here as it disrupts equilibrium, whereas throttle modulation offers superior speed control. Maintain throttle in the linear power/torque range for instant acceleration or deceleration readiness. During gear shifts; Gear changes are deeply linked to throttle response. Different gears require specific engine RPM ranges for immediate power delivery—all controlled via throttle. The shift moment creates engine no-load conditions where abrupt throttle input may cause RPM spikes, leading to post-shift power instability and jerking. Thus, execute throttle-off shifts with simultaneous throttle blips. Downshifts requiring smooth power maintenance need slightly higher RPMs for better acceleration.
2
1
Share

How to Activate Cruise Control on the New Focus?

The method to activate cruise control on the New Focus: 1. Press the CRUISE button to turn on the system, at which point the cruise control indicator light on the dashboard will illuminate; 2. Accelerate to the desired speed, then press the SET button—you can now remove your foot from the accelerator as the speed is set at the current rate; 3. You can fine-tune the speed using the RES and SET buttons. The New Focus retains the body dimensions of the current Focus model, measuring 4534 mm in length, 1823 mm in width, and 1483 mm in height, with a wheelbase of 2648 mm. In terms of exterior design, the New Focus features sleek, elongated headlights paired with smooth body lines, giving the car a sporty overall appearance.
18
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.