Where is the fuse located in the Lavida car?

Why does the GAC Trumpchi GS4 prompt to check the airbag?

Trumpchi GS4's 'Check Airbag' warning may be caused by a depleted smart key battery. The system cannot detect the presence of the key, which triggers the lock symbol illumination on the dashboard. Please check if the key's voltage is normal. The airbag control module is typically located in front of or beneath the gear lever. Below is relevant information about airbags: The airbag system is a passive safety protection system (refer to vehicle safety performance). When used in conjunction with seat belts, it provides effective collision protection for occupants. During a vehicle collision, automotive airbags can reduce head injury rates by 25% and facial injury rates by approximately 80%.

5

0

Share

Can Lane Keeping Be Retrofitted?

Lane keeping can be retrofitted, with the following main features: 1. The Lane Keeping Assist System (LKAS) is part of the intelligent driving assistance system. It can control the brake coordination device based on the Lane Departure Warning System (LDWS). While driving, the system uses a camera to identify lane markings and keeps the vehicle within the lane. If the vehicle detects that it may deviate from the lane, it alerts the driver through steering wheel vibration or audible warnings. 2. If the Lane Keeping Assist System identifies markings on both sides of the lane, the system remains on standby. In this state, if the turn signal is activated before crossing the lane markings, the warning signals are suppressed, assuming the driver is intentionally changing lanes. Currently, this system is primarily used on structured roads.

19

0

Share

What is the working principle of the clutch disc and pressure plate?

The working principles of the clutch disc and pressure plate are as follows: 1. The working principle of the clutch disc is to transmit power to the driven disc through the friction between the flywheel, pressure plate, and the contact surface of the driven disc. When the driver presses the clutch pedal, the mechanism causes the large end of the diaphragm spring to push the pressure plate backward, separating the driven part from the driving part. 2. The working principle of the clutch pressure plate: The clutch housing, including the intermediate pressure plate, is installed on the plunger at the rear end face of the flywheel. Under the action of the spring, the pressure plate engages with the friction disc, transmitting the engine power to the transmission. The clutch mainly consists of the flywheel and the clutch pressure plate. The flywheel is a metal disc directly connected to the crankshaft in the engine, rotating the same number of times as the engine crankshaft. The clutch pressure plate is directly connected to the transmission.

12

0

Share

What are the differences between cornering lights and adaptive headlights?

Cornering lights differ fundamentally from adaptive headlights in that adaptive headlights achieve their function by rotating the reflector bowl and bulb, while cornering lights employ a small bulb set at a specific angle within the headlight assembly that illuminates at predetermined times. In practical use, cornering lights are less effective at illuminating blind spots compared to adaptive headlights. Details about cornering lights and adaptive headlights are as follows: 1. Cornering lights refer to a separate set of bulbs that illuminate on one side when the driver turns the steering wheel (some vehicles use fog lights as cornering lights), assisting in lighting up blind spots during turns. Shortly after the steering wheel returns to the straight position, the cornering light on that side turns off. 2. Adaptive headlights, also known as dynamic bending lights, rotate the headlight assembly towards the direction of the turn to a certain degree, expanding the field of vision. This allows the headlights to illuminate 'unreached' areas in advance, providing comprehensive safety lighting to ensure optimal visibility for the driver at all times.

11

4

Share

What is the difference between mineral oil and full synthetic oil?

The biggest difference between mineral oil and full synthetic oil lies in the fact that synthetic oil has a wider temperature range, longer service life, and higher cost. Under the same oil film requirements, full synthetic oil can achieve this with a lower viscosity, while mineral oil requires a relatively higher viscosity compared to full synthetic oil to meet the same requirement. The specific differences between mineral oil and full synthetic oil are as follows: 1. Refining and composition: Mineral oil is directly refined from crude oil as its base, with additives then mixed in; semi-synthetic oil is based on mineral oil with synthetic oil additives added, making its performance very close to full synthetic oil; full synthetic oil is 100% made from polyalphaolefins (PAO) or artificially synthesized esters. 2. Performance: Since mineral oil is directly refined from crude oil, impurities are inevitable, while full synthetic oil, being artificially synthesized, has the highest purity. Mineral oil < semi-synthetic oil < full synthetic oil. 3. Price: Mineral oil < semi-synthetic oil < full synthetic oil.

3

1

Share

How to Test if a Thermostat is Good or Bad?

Remove the thermostat from the engine, clean it, and then heat it in hot water. Use a thermometer with a range of 100°C to measure the temperature. According to the specified temperature at which the thermostat valve opens or the side valve closes, check whether its performance is good and whether it works reliably. Information about the thermostat is as follows: 1. The thermostat is a valve that controls the flow path of the coolant. It is an automatic temperature-regulating device, usually containing a temperature-sensing component, which opens or closes the flow of air, gas, or liquid through thermal expansion or contraction. 2. The function of the thermostat is to prevent the engine from becoming too cold. After the engine is operating normally, if there is no thermostat when driving at high speed in winter, the engine temperature may be too low. At this time, the engine needs to temporarily stop the water circulation to ensure that the engine temperature does not become too low.

20

2

Share

Where is the fuse located in the Lavida car?

Why does the GAC Trumpchi GS4 prompt to check the airbag?

Can Lane Keeping Be Retrofitted?

What is the working principle of the clutch disc and pressure plate?

What are the differences between cornering lights and adaptive headlights?

What is the difference between mineral oil and full synthetic oil?

How to Test if a Thermostat is Good or Bad?

How to Remove the Rear Seat of an Accord Sedan?

What type of oil does the Changan CS35 use?

How to Perform Tire Rotation?

What is the purpose of car windshield washer fluid?