Where is the fuse for the wiper motor in the new Santana?

What are the symptoms of a damaged footwell module in a BMW?

When the footwell module in a BMW is damaged, it can cause the CPU data on the circuit board to be lost, leading to control failures in the lighting system, door locks, central locking, and window regulators. Symptoms may include turn signal failure, headlights staying on, inability to raise or lower the front windows, and inability to adjust the mirrors. More details about the footwell module are as follows: 1. The footwell module, abbreviated as FRM, is an electrical node located in the driver's side footwell area. It consists of a circuit module with a CPU and primarily controls the vehicle's windows, headlights, and communication system, making it an essential part of the vehicle's control system. 2. Causes of FRM data loss: Not turning off the ignition switch when replacing the battery, grounding the battery terminals, or improper battery operations performed by non-professionals.

9

2

Share

How to Replace the Rear Brake Pads of a Zotye T600?

First, loosen the tire bolts, then use a jack to lift the rear wheel, release the electronic parking brake, and use tools to loosen the bolts of the brake caliper. Replace with new brake pads, then reinstall the brake caliper. The rear brake pad replacement is now complete. Below is some related information: 1. The braking system on a car is equivalent to a life-saving system. Whether the car can move is not as important as whether it can stop, making brakes particularly crucial. 2. Based on the application, brake pads can be categorized into disc brake pads, drum brake pads, and truck brake linings. In terms of friction material composition, brake pads mainly include asbestos brake pads, semi-metallic brake pads, low-metallic brake pads, NAO formula brake pads, ceramic brake pads, and NAO ceramic brake pads.

12

3

Share

Is it allowed to turn right at a traffic light intersection without any signs?

At a traffic light intersection without any signs indicating that right turns are allowed, turning right without affecting the straight-moving vehicles traveling in the same direction is not illegal. Violations of traffic rules will be penalized with 3 demerit points, a warning, or a fine. According to the "Road Traffic Safety Law of the People's Republic of China": Article 44: When motor vehicles pass through intersections, they shall proceed in the direction indicated by traffic signals, traffic signs, traffic markings, or the command of traffic police. Here is additional information: 1. Article 44 of the Road Traffic Safety Law of the People's Republic of China: When motor vehicles pass through intersections, they shall proceed in the direction indicated by traffic signals, traffic signs, traffic markings, or the command of traffic police; when passing through intersections without traffic signals, traffic signs, traffic markings, or the command of traffic police, they shall slow down and yield to pedestrians and vehicles with the right of way. 2. Article 45: Motor vehicles shall not overtake or occupy the opposite lane when queued or moving slowly in front. Motor vehicles shall alternate passage in sections or intersections with reduced lanes, or at intersections without traffic signals, traffic signs, traffic markings, or the command of traffic police to stop, queue, or proceed slowly. 3. Article 46: Motor vehicles passing through railway crossings shall proceed according to traffic signals or the command of management personnel; in the absence of traffic signals and management personnel, they shall slow down or stop to ensure safety before proceeding. 4. Article 47: Motor vehicles shall slow down when passing through pedestrian crossings; when pedestrians are crossing, they shall stop and yield. Motor vehicles shall yield to pedestrians crossing the road where there are no traffic signs.

13

1

Share

What to Do When the Car Battery Is Dead and the Engine Won't Start?

Here are the methods to handle a dead car battery that prevents the engine from starting: 1. Push-starting is the most common and effective emergency starting method. However, this is a last resort and should not be used frequently, as it can cause some damage to the engine and clutch. This method should especially be avoided for automatic transmission vehicles. 2. To avoid being unable to charge the battery when it's dead, car owners should keep a set of jumper cables in the vehicle, which can be purchased at general auto parts stores. However, when connecting the jumper cables, it is crucial not to mix up the connection order. First, connect the positive terminal of the dead battery to the positive terminal of the rescue vehicle's battery. Then, connect the negative terminal of the rescue vehicle's battery to a metal part in the engine compartment of the dead car. 3. The most reliable method is to promptly contact a rescue vehicle, connect the jumper cables, and temporarily charge the dead battery to start the engine.

6

4

Share

What Causes High Idle Speed?

Causes of high idle speed: 1. The engine's throttle is dirty or malfunctioning. 2. The engine's spark plugs are faulty. 3. Excessive carbon buildup in the engine combustion chamber, intake tract, fuel injectors, or intake manifold, leading to incomplete combustion of the mixture. Below is an introduction to idle speed: 1. Idle state refers to a working condition when the engine is running without load. When the engine is running and the accelerator pedal is fully released, the engine is in an idle state. The reason idle speed increases fuel consumption is that the engine is not operating under normal conditions. 2. At idle, the engine speed is very low, the intake turbulence weakens, and poor fuel atomization leads to incomplete combustion. Additionally, the prolonged fuel combustion time and increased heat dissipation loss from the cylinders also contribute to higher engine fuel consumption.

3

1

Share

Where is the car ETC installed?

The installation position of the car ETC is generally in the upper middle part of the front windshield, while for large vehicles such as trucks and buses, the installation position is in the middle and lower part. The appropriate installation position is at a height of no less than 1.2 meters and no more than 2.5 meters, and the installation angle should be between 30 and 90 degrees. For vehicles with anti-explosion film or those that have been retrofitted with anti-explosion film, it will affect the signal transmission of the microwave communication link, so it should be installed in the microwave skylight band. ETC is the abbreviation of Electronic-Toll-Collection, which means electronic toll collection system. To apply for it, you need to provide the original and photocopy of the owner's valid ID card and vehicle license. If it is not the owner who applies, the agent's valid ID card is also required. The photocopy of the vehicle license needs to include the page with the most recent annual inspection stamp. A bank card for deducting highway tolls is also needed, and the vehicle must be registered under the name of an individual aged between 18 and 60. Here are the precautions for installing ETC: Do not block the view. It is best to install it behind the rearview mirror: Many car models have a large inclination angle of the windshield, which results in a smaller driver's field of vision. If this is not taken into account when installing ETC, it will increase the driver's blind spot. Install it behind the rearview mirror on the right side to avoid blocking the view. Do not affect charging: The ETC electronic tag consumes power, but generally does not need to be charged or have its battery replaced because it has a solar panel on the back that can charge itself. Therefore, when installing, avoid the black area on the windshield and do not install it in a position where the solar panel is easily blocked. Once installed, do not remove it at will: The button in the middle of the adhesive is an anti-removal guide rod, which is connected to a switch below. After the electronic tag is installed, the windshield will press the anti-removal guide rod in. If it is removed at will, the anti-removal guide rod will pop out and trigger the switch, and the electronic tag will be locked and cannot be used. You will need to go to the ETC service point to unlock it. This is designed to prevent multiple vehicles from sharing one device. When using ETC, note that: The ETC transaction sensing area is 8 meters. To prevent the ETC device of the vehicle in front from malfunctioning, keep a distance of more than 10 meters from the vehicle in front to avoid automatic sensing and paying for the vehicle in front. The recognition speed of the ETC lane is 20 kilometers per hour. If the speed is too fast, the vehicle device information cannot be read, which will lead to failure of deduction. When using a debit card to bind ETC, insufficient balance will also lead to failure of deduction.

7

0

Share

Where is the fuse for the wiper motor in the new Santana?

What are the symptoms of a damaged footwell module in a BMW?

How to Replace the Rear Brake Pads of a Zotye T600?

Is it allowed to turn right at a traffic light intersection without any signs?

What to Do When the Car Battery Is Dead and the Engine Won't Start?

What Causes High Idle Speed?

Where is the car ETC installed?

Where is the light switch located in a Ford car?

How to use a newly installed ETC?

How to Turn on the Headlights of a Haval F5?

What is the fuel consumption of the Arrizo 5plus?