Where is the fuse box of the Buick Excelle?

Where is the DISP button on the Changan CS15?

The DISP button on the Changan CS15 is located on the multifunction steering wheel, and the button icon is a rectangle. The following are the specific functions of the DISP button on the Changan CS15: 1. The condition of a vehicle is generally proportional to its mileage. The higher the mileage, the more severe the wear and tear on its parts. 2. The fuel consumption of a vehicle indirectly reflects the condition of its parts. For example, severely worn tires may frequently slip, leading to increased fuel consumption. 3. When the fuel level is low, it indicates that the remaining driving range is limited, and the vehicle needs to be refueled. 4. After driving a certain distance, it is necessary to check the remaining driving range, which indicates how much farther the vehicle can travel.

14

1

Share

Why can't the remote key open the car door?

Here are the reasons why the remote key cannot open the car door: 1. If the remote key cannot open the door, it may be due to the remote key being out of battery or the car battery being dead. 2. If the mechanical key also cannot open the door, it may be because the car's lock control system is in an electronic lock state, or the door lock cylinder is stuck. Here are some precautions for car doors: 1. Try to avoid letting the car door locks get wet in the rain, as the small springs inside the door locks can easily rust when wet, leading to reduced flexibility. 2. When using the door lock, if you find it difficult to open or close, spray lubricant on the lock tongue. 3. In extremely cold weather, the car door may freeze. In such cases, use warm water to thaw it or wait for the temperature to rise before opening.

8

0

Share

Is a tire pressure of 220 normal for Cadillac XT5?

Normal. Specific information about car tire pressure is as follows: 1. Range: Car tire pressure is generally considered normal between 2.2~2.5, but tire pressure is not fixed and needs to be adjusted appropriately according to changes in season, load, road conditions, etc. For example, it can be slightly lower in hot summer weather and slightly higher in cold winter weather. 2. Manufacturer's recommended tire pressure values: Different vehicle models have different requirements for tire pressure, including different maximum and minimum limits. The manufacturer's recommended tire pressure values can be found in the vehicle owner's manual, specifically on the label near the driver's door (B-pillar area).

12

0

Share

What does it mean when the ABS light on the dashboard is on?

When the ABS light is displayed on the car, it means there is a malfunction in the vehicle's Anti-lock Braking System. During emergency braking, if the wheels lock up, the vehicle may lose control and skid, making it difficult for the driver to slow down or adjust the vehicle's trajectory, which poses a significant safety hazard. There are various states of the ABS light being on, and the causes and solutions differ depending on the state. The details are as follows: State 1: ABS warning light stays on (most common). Cause 1: The ABS speed sensor's sensing part is covered by dirt, mud, or other contaminants, affecting the sensor's ability to detect the corresponding speed signal. This prevents the ABS computer from determining the vehicle's speed and the wheel's slip rate, thus failing to issue appropriate commands to adjust braking. Solution: Clean the dirt from the speed sensor and adjust the gap between the speed sensor and the signal ring to restore normal function. Cause 2: Loose connections between system wires or poor contact in the ABS relay can lead to signal issues and system failure. Solution: Check the wire connections and reconnect any loose parts. State 2: ABS warning light intermittently turns on but goes off when accelerating. Cause: When multiple electrical devices are used, the battery voltage drops below 10.5V. As the engine speed increases, the voltage rises, and the ABS light turns off. This may also occur if the ABS system's power supply voltage is too low due to poor contact or grounding issues. Solution: Check the battery's specific gravity; inspect the charging system; examine the power supply (e.g., voltage relay or poor power contact). State 3: ABS warning light stays on after engine start and only turns off when the engine is turned off (IGFF). Cause: Poor grounding contact in the ABS hydraulic valve body; loose wiring connections in the ABS hydraulic valve body; ABS computer malfunction. Solution: Loosen and retighten the grounding screws of the hydraulic valve body, cleaning the contact surface if necessary; check if the connector gap has widened; replace the ABS or ABS/ASR computer. State 4: ABS warning light turns on during high-speed driving. Cause: During high-speed driving, the ABS computer detects a significant difference between the rear and front wheel speed signals; incorrect tire or wheel rim specifications. Solution: Refer to the vehicle's tire and wheel rim specifications, as indicated on the fuel tank cap sticker. State 5: ABS warning light intermittently turns on. Cause: Improper adjustment of the brake light switch; poor internal contact in the brake light. Solution: Start the engine, press the brake pedal, push the brake switch linkage down with your finger, then release the brake pedal to complete self-setting; replace the brake light switch if necessary.

3

5

Share

How to Repair Scratched Car Paint?

Minor scratches on car paint can be repaired using fine polishing wax. The principle involves rearranging the molecules of the surface paint layer, effectively moving adjacent surface paint to cover the scratch. Below is an introduction to car paint scratches: 1. The role of the paint film: Car paint must have a paint film with good mechanical properties, excellent fullness, and high gloss. It should also possess strong adhesion, high hardness, and scratch resistance, along with good weather resistance, wear resistance, gloss retention, and resistance to gasoline, alcohol, acid, alkali, and salt spray. 2. Precautions: Unless absolutely necessary, avoid repainting body scratches. This is because the original factory paint includes an electrophoretic layer, which is absent in repainted areas. The lack of an electrophoretic layer can lead to poor adhesion, noticeable color differences, and other issues. Additionally, the original factory paint has more advanced application techniques, resulting in significantly better quality compared to repainted areas.

5

1

Share

Is it necessary to install a license plate bracket?

License plate brackets are necessary to install. Here is a detailed introduction to license plate brackets: 1. Function: A license plate bracket is a frame for holding the license plate, also known as a license plate frame or license plate holder. There is one each at the front and rear of the vehicle. It serves to fix the license plate, protect the license plate, protect the vehicle body, and prevent the license plate from damaging the body. Additionally, installing anti-theft screws on the bracket can provide anti-theft functionality. 2. Compatibility: Some imported vehicles have license plate mounting holes that differ from those of domestic vehicles. License plate brackets can also address the compatibility issues of installing license plates on imported vehicles.

17

2

Share

Where is the fuse box of the Buick Excelle?

Where is the DISP button on the Changan CS15?

Why can't the remote key open the car door?

Is a tire pressure of 220 normal for Cadillac XT5?

What does it mean when the ABS light on the dashboard is on?

How to Repair Scratched Car Paint?

Is it necessary to install a license plate bracket?

How much oil should be added to a BMW 320li?

How to Start the Qoros 5?

Where is the OBD port of Wuling Hongguang?

Should a new car be sealed with glaze?