Where is the fuse box of the Besturn B50 located?

1 Answers
MarianaLee
07/29/25 4:05pm
The FAW Besturn B50 has two fuse boxes containing the vehicle's fuses. One is located on the right side of the engine compartment, primarily responsible for the safety of external electrical components such as ECU, windshield washer fluid, lights, horn, ABS circuit protection, etc. The other is situated on the lower left side of the steering column, mainly ensuring the proper functioning of interior electrical components like the cigarette lighter, power windows, electric seats, and airbags. Below is relevant information: 1. Introduction to the B50: The Besturn B50 is an independently developed vehicle by FAW Car, launched on May 16, 2009. 2. Configuration: The new Besturn B50 has undergone configuration upgrades to further enhance safety and comfort. It now features a cornering lighting system that automatically controls the cornering lights (front fog lights) based on driving conditions and vehicle status.
Was this review help?
2
0
Share
More Forum Discussions

What to Do If Your Driver's License Expires for Ten Days?

Bring the original ID card, a copy of the ID card, a physical examination certificate from a hospital at or above the county level, the original driver's license, and four one-inch white background photos to the vehicle management office to renew the license. Below are specific details about driver's license expiration: 1. Expired for one year: After the driver's license expires, you are not allowed to drive a motor vehicle. If the license has been expired for more than one year without renewal, the traffic management department will cancel your motor vehicle driver's license. 2. Expired for two years: If the license has been expired for more than two years, the motor vehicle driver's license will be canceled, and you can restore the normal use of the driver's license by passing the subject one exam. 3. Early renewal: You can renew your driver's license within 90 days before its expiration date.
13
0
Share

What are the steps for cleaning the throttle body?

Throttle body cleaning steps are as follows: First, unplug the wiring harness connector near the throttle body, use a hex screwdriver to remove the fixing screws, and then take off the throttle body. Cover the intake port to prevent debris from falling into the engine. Spray cleaner on the dirt. Be careful not to spray the cleaner outside the throttle body, do not forcefully pry the internal throttle plate, and avoid damaging the adjacent throttle motor. Finally, let it dry naturally. It's best not to wipe with a cloth, as it may remove the surface lubricating coating. After reinstalling the throttle body, perform a power reset or throttle body relearn procedure.
2
1
Share

What Should You Pay Attention to When Buying a Used Car?

When purchasing a used car, pay attention to the car's performance, structure, documentation, and appearance. The main issues are introduced as follows: Performance: Listen for any abnormal sounds, start the car, and listen to the engine noise. Structure: Check the chassis and frame for any deformation. After an accident, the frame and chassis are difficult to repair. Documentation: Documents such as the registration certificate, vehicle license, and purchase tax. Always take a test drive, whether buying a new or used car. Appearance: Inspect all corners and parts of the car for repainting, and check for wear on the tires, headlights, and bumper.
10
0
Share

What are the automotive parts and accessories?

The automotive parts and accessories include engine components, transmission system parts, braking system parts, steering system parts, suspension system parts, electrical and instrument components, automotive lighting, car modification accessories, and safety and anti-theft accessories. Automotive parts are the individual units that make up the entirety of automotive parts processing and products that serve the automotive parts processing. Below is a detailed introduction: 1. Engine components: mainly include the engine, engine assembly, throttle body, cylinder block, tension pulley, etc. 2. Transmission system parts: mainly include the clutch, transmission, gear shift lever assembly, reducer, magnetic materials, etc. 3. Braking system parts: mainly include the master cylinder, wheel cylinder, brake assembly, brake pedal assembly, compressor, brake disc, brake drum, etc. 4. Steering system parts: mainly include the kingpin, steering gear, steering knuckle, ball joint, etc. 5. Suspension system parts: mainly include the rear axle, air suspension system, balance weight, steel plate, etc. 6. Electrical and instrument components: mainly include sensors, automotive lighting, spark plugs, batteries, etc. 7. Automotive lighting: mainly includes decorative lights, fog lights, dome lights, headlights, brake lights, reverse lights, turn signals, instrument lights, indicator lights, searchlights, and other various automotive lights. 8. Car modification accessories: mainly include tire inflators, car roof boxes, car roof racks, electric winches, etc. 9. Safety and anti-theft accessories: mainly include steering wheel locks, wheel locks, seat belts, cameras, etc.
19
1
Share

Can a dented car fender be pulled out?

Fender dents can be pulled out. Here are specific details about car fenders: Characteristics of car fenders: A fender is a type of cover on motor vehicles and non-motor vehicles, acting as an outer shell. It conforms to fluid dynamics, reducing the drag coefficient and making the vehicle more stable during movement. Introduction to front and rear fenders: The front fender is installed near the front wheel and must ensure the maximum space for wheel rotation and movement. The rear fender does not face issues with wheel rotation friction. For aerodynamic considerations, the rear fender has a slightly arched curve and protrudes outward.
18
5
Share

Do automatic transmission cars have handbrakes?

Automatic transmission cars do have handbrakes. Below is relevant information about handbrakes in automatic transmission cars: Mechanical handbrake: The mechanical handbrake mainly consists of a brake lever, steel cable, brake mechanism, and return spring. It uses a steel wire cable connected to the rear brake shoes to secure the vehicle and prevent it from rolling. It offers good stability and low usage costs. Electronic handbrake: The electronic handbrake replaces traditional parking brake handles, mechanical levers, and control cables with electronic buttons and motor components. During braking, the electronic control unit will activate the motors integrated in the left and right brake calipers, driving the brake caliper pistons to move and generate mechanical clamping force to complete the parking process.
5
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.