Where is the fuel tank switch of the Excelle located?

3 Answers
MacCaden
07/29/25 2:23am
Excelle fuel tank switch is located on the left side of the driver's seat. The following is the relevant content: Excelle fuel tank switch: The fuel tank switch of the Excelle is located on the left side of the driver's seat. Pull up the fuel filler door switch to release the handle and open the fuel filler door. The fuel tank switch lock is integrated with the car door lock. When you lock the car doors, the fuel tank cap is also locked. When you unlock the car doors with the key, the fuel tank lock is released, allowing you to directly open the fuel tank cap. Introduction to the Excelle: The Excelle is a compact sedan produced by SAIC-GM Buick. It is equipped with a 1.3T 48V mild hybrid engine and a 1.5L DVVT four-cylinder engine, comprehensively balancing power, fuel consumption, and a good driving experience. The diverse options cater to the needs of different consumers, providing owners with an efficient and agile power experience.
Was this review help?
14
3
Share
MacHeidi
08/12/25 12:28pm
I've been driving a Buick Excelle for several years, and every time I refuel, I have to figure out where the fuel tank switch is. Actually, it's not a separate button but integrated into the door lock system. The location is right above the handle on the inner side of the driver's door, where there's a door lock button. When you use the key remote to unlock the entire car, the fuel tank door also unlocks automatically; when you lock the car, it locks simultaneously. This design is quite safe, preventing fuel theft. I must remind you to always turn off the engine before refueling, then press the fuel tank cap to open it. Once, I forgot to do this, causing the warning light to come on, which was quite troublesome. The car's intelligent design makes daily refueling much simpler, eliminating the need to manually find the switch.
Was this review help?
14
3
Share
Expand All
VonJaxon
10/02/25 4:05am
As a car enthusiast, I always enjoy delving into the details of modern cars like the Excelle. The fuel tank switch isn't a traditional physical button; it's integrated into the central control electronic system. Located either below the steering wheel on the left side or on the unlock button near the door frame, pressing it automatically releases the fuel tank latch. The design employs an electronic lock, offering better anti-theft protection than mechanical systems. When refueling, a light press on the fuel cap pops it open, but the car must be unlocked first. If the battery dies, the manual explains how to use the key to forcibly open the emergency pull cord located in the trunk. This method is quite useful in emergencies. Overall, the system is simple and reliable.
Was this review help?
9
5
Share
Expand All
More Forum Discussions

How to Solve the Engine Immobilizer Authentication Failure Issue on Baojun 510?

Fellow car owners should first check their car keys. The remote key fob contains a dedicated module specifically for engine starting. Simply pry open the casing, remove the old battery and replace it with a new one.
8
1
Share

How to Remove the Fuel Pump on a Buick Excelle?

First remove the rear seat to expose a black metal cover secured by four screws. Unscrew these to reveal the fuel pump. Disconnect all wiring connections, then use a specialized fuel pump removal tool to unscrew and extract the unit.
9
1
Share

How to fix the peeling dashboard of a Buick Excelle?

If the dashboard warping issue occurs during the car's warranty period, you can contact after-sales service for relevant handling. If the car's warranty period has expired but the dashboard warping issue occurs, you can go to an auto repair shop for handling.
13
2
Share

What Causes the ABS Light to Illuminate in a Jaguar?

ABS light illumination can occur in various states, with different causes and solutions for each state, as detailed below: State 1: ABS warning light remains constantly lit (most common). Cause 1: The ABS wheel speed sensor's sensing area is covered by dirt, mud, or other contaminants, affecting the sensor's ability to detect the corresponding speed signal. This prevents the ABS control unit from determining the vehicle speed and wheel slip rate, thus failing to issue appropriate commands to regulate braking. Solution: Clean the contaminants from the wheel speed sensor and adjust the gap between the sensor and the signal ring to restore normal operation. Cause 2: Poor signal transmission due to loose system wiring connections or poor contact in the ABS relay, leading to system malfunction. Solution: Inspect wiring connections and reconnect any loose parts. State 2: ABS warning light intermittently illuminates but turns off during acceleration. Cause: When multiple electrical components are in use, the battery voltage drops below 10.5V. As engine speed increases, voltage rises, and the ABS light turns off. This may also occur due to insufficient power supply voltage to the ABS system, such as poor terminal contact or grounding issues. Solution: Check the battery's specific gravity; inspect the charging system; examine the power supply (e.g., voltage relay or poor power contact). State 3: ABS warning light remains lit after engine startup until the engine is turned off (IGFF). Cause: Poor grounding contact in the ABS hydraulic valve body; poor electrical connector contact in the ABS hydraulic valve body; ABS control unit malfunction. Solution: Loosen and then retighten the grounding screw on the hydraulic valve body, cleaning the contact surface if necessary; check for enlarged connector gaps; replace the ABS or ABS/ASR control unit. State 4: ABS warning light illuminates during high-speed driving. Cause: During high-speed driving, the ABS control unit detects a significant discrepancy between rear and front wheel speed signals; incorrect tire or wheel rim specifications. Solution: Refer to the vehicle's specified tire and wheel rim specifications, typically listed on the fuel tank cap sticker. State 5: ABS warning light intermittently illuminates. Cause: Improper adjustment of the brake light switch; poor internal contact in the brake light. Solution: With the engine running, press the brake pedal and manually push the brake switch linkage fully downward, then release the pedal to complete self-positioning; replace the brake light switch if necessary. If the ABS warning light is illuminated, it is advisable not to continue driving. An illuminated ABS light indicates a malfunction in the vehicle's anti-lock braking system. During emergency braking, if the wheels lock up, the vehicle may skid uncontrollably, preventing the driver from slowing down or adjusting the vehicle's trajectory, posing significant safety risks.
17
1
Share

How to adjust the ambient lighting in the 2021 Audi A6L?

You can adjust the interior ambient lighting through the MMI display. Press the CAR button to select the system and enter the background lighting interface. The ambient lighting at the front footwells, rear footwells, front door panels, and rear door panels can all be set via the MMI.
2
0
Share

How to Repair Cracked Leather in Car Interior?

Use a soft brush and a slightly damp towel to thoroughly clean the leather that needs repair or has wrinkles. Sand the leather surface that requires repair with water sandpaper, and remove any already cracked leather as well. Apply leather repair paste to the surface that needs fixing, spray a layer of primer on the leather surface, then complete the coloring within 60-150 seconds.
13
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.