Where is the fuel tank switch of the Buick Excelle?

2 Answers
MiaRose
07/23/25 8:56pm
The fuel tank switch button of the Buick Excelle is located at the bottom left side of the driver's seat. Lift it upward and release to open the fuel filler cap. The Buick Excelle fuel gauge has eight bars, and the fuel tank capacity is 44 liters. If the fuel level is too low, the fuel control indicator will light up. If the indicator flashes, refuel immediately and do not let the fuel tank run empty. Below is an introduction to the car's fuel system: 1. Before adding fuel, turn off the engine switch and ensure all doors and windows are closed. The fuel type is unleaded gasoline, and ethanol gasoline with an ethanol content of up to 10% is allowed. 2. The fuel type is unleaded gasoline with an octane rating of 92 or higher. Use ethanol gasoline with an ethanol content of up to 10%, ensuring the octane rating of the ethanol gasoline meets the above standards. 3. Frequently mixing gasoline from Sinopec and PetroChina, the two major brands, may lead to carbon deposits and affect engine performance due to differences in their processes, standards, and additives.
Was this review help?
18
4
Share
DelAndrew
08/10/25 6:51pm
In my Buick Excelle, the fuel tank release lever is actually quite easy to find. It's located on the floor in the driver's footwell area to the left, marked with a small fuel droplet or gas station icon. When I first got the car, I was confused too, but later discovered its ergonomic design - positioned within easy reach for quick fuel door release without exiting the vehicle. Most modern cars arrange interior switches this way to prevent accidental operation by children, enhancing safety. When refueling, simply turn off the engine, pull the lever, then operate the fuel filler door. If you can't locate it at first, don't worry - crouch down for a closer look or check the owner's manual diagrams. Remember to keep the switch area clean and free of dust buildup. Once you get used to it, operating becomes effortless.
Was this review help?
16
5
Share
Expand All
More Forum Discussions

What is the issue when both 4H and 4L lights are on simultaneously?

4H and 4L lights indicate a fault in the four-wheel drive system. Fault confirmation: 1. Start the vehicle and observe that the green four-wheel drive indicator light on the dashboard flashes continuously regardless of the position of the transfer case shift lever (normally, it should light up when engaged in four-wheel drive and turn off when switched to two-wheel drive). 2. Lift the vehicle so that all four wheels are off the ground, shift the transfer case lever to 4H, 4L, and 2H positions, but only the rear wheels are driven, with the front wheel speed remaining at zero, unable to switch to four-wheel drive. 3. Review the maintenance records; the vehicle has no relevant repair history, recent maintenance was not performed at an authorized dealership, and the transmission wheel speed sensor was replaced, with no other abnormalities found.
10
1
Share

How to reset the tire pressure warning light on a Golf 7?

To reset the tire pressure warning light on a Golf 7: Press and hold the tire pressure reset button, which is located on the panel next to the gear lever. Hold it for 3 seconds until you hear a beep, and the tire pressure warning light on the dashboard will disappear. There are two reasons for the tire pressure warning light: either the tire pressure is too low or too high. If the tire pressure is too low, you should visit a tire repair shop to check the tires and adjust the pressure to the standard value. If the tire pressure is too high, inflate the tires according to the manufacturer's specified pressure value. For the interior, the Golf 7 is equipped with white LED ambient lighting in the front footwells, front interior door handles, and front door trim strips. The brightness of the ambient lighting can be adjusted via the vehicle's computer.
9
2
Share

Why Does a Car Emit Black Smoke?

Reasons for a car emitting black smoke: 1. Uneven or excessive fuel supply from the high-pressure fuel pump to each cylinder can cause unstable engine speed and intermittent black smoke; 2. Poor quality diesel fuel, which is difficult to ignite, leads to black smoke from the exhaust and also easily causes carbon buildup in the combustion chamber and exhaust pipe muffler; 3. Overly rich air-fuel mixture, resulting in incomplete combustion, which can be caused by various factors such as high fuel pressure, poor ignition performance, or inaccurate signals from the intake pressure sensor; 4. Severe wear of the cylinder liner and piston components. In this case, the piston rings do not seal properly, causing a significant drop in cylinder pressure, which prevents the diesel from burning completely and results in black smoke. Additionally, the engine power drastically decreases, and in severe cases, the engine may shut down automatically.
18
2
Share

What is the battery model for the Ford Kuga remote key?

Ford Kuga key battery model is CR2032. CR2032 is a lithium manganese dioxide battery, named according to the IEC standard. Among them: C- indicates a chemical battery system with lithium metal as the negative electrode and manganese dioxide as the positive electrode; R- indicates that the battery is cylindrical in shape, with F used if it is square; 20 indicates the battery diameter is 20mm; 32 represents the battery height is 3.2mm. The nominal voltage is 3.0V, the endpoint voltage is 2.0V, and the rated capacity varies between 200-240mAh depending on the manufacturer's quality. The shelf life of CR2032 is typically 5 years. If the manufacturer's production level is low or quality control is poor, its lifespan can be significantly shortened. Domestic first-tier brand batteries can generally guarantee this lifespan. Under ideal usage conditions (sealed, room temperature, no moisture interference, etc.), the lifespan can be extended further to 8 years or even 10 years. Generally, replacing a car key battery only requires the following 3 steps: Step 1: Remove the mechanical key. Press the lock button on the side of the smart key to remove the mechanical key. Step 2: Open the battery cover. After removing the mechanical key, you can see a deep slot and a shallow slot at the top of the smart key. The deep slot is the keyhole, while the shallow slot is used to open the battery cover. Insert the mechanical key into the shallow slot and pry it outward to open the battery cover. Once opened, you can see the coin cell battery, which can be removed with a gentle push. Step 3: Replace the new battery. Install the new battery, then reattach the battery cover and mechanical key in order to complete the battery replacement.
7
5
Share

How to Install a Beam Wiper Blade?

Press the lower part of the wiper clip, flip the clip open, hook it onto the wiper mounting base, and then close the wiper clip. If there are any foreign substances such as oil, wax, or dirt on the windshield, clean them thoroughly before use. A beam wiper blade is composed of four parts: the wiper rubber, the beam wiper steel strip, the wiper cover, and plastic components. Compared to traditional wiper installation, assembling a beam wiper is very simple and convenient; it only requires manual assembly by workers without the need for tools like screwdrivers. Below are the maintenance methods for wiper blades: 1. When using the wiper to remove dust from the windshield on sunny days, always spray windshield washer fluid and avoid dry wiping. 2. If there are other stubborn or hard contaminants on the glass, clean them manually. These substances can easily damage the wiper blade, causing it to wipe poorly. In severe cases, the wiper motor may also be affected. 3. When lifting the wiper blade during car washing or daily cleaning, hold the "backbone" of the wiper blade and gently return it to its position. Do not let the wiper blade snap back abruptly. 4. In winter, use an ice scraper to remove ice chips from the windshield surface first to avoid putting extra strain on the wiper.
12
3
Share

What does MCS mean on a car?

MCS on a car refers to the knob that controls the display. Pressing it confirms selections, adjusts idle speed, and rotating it allows viewing of fuel consumption data such as per 100 kilometers, instantaneous fuel consumption, engine operating time, and total fuel consumption. A single rotation switches to the next item. By rotating the knob, different information can be accessed. This feature is exclusively found on HOWO heavy-duty trucks and serves as a convenient real-time monitoring function. Below are related details: 1. The MCS on HOWO trucks functions as a channel switch, integrating online data and technology with offline store services to create a comprehensive new retail platform for automobiles. 2. Through innovations in models, channels, and product technology, the HOWO MCS switch meets the diverse automotive service needs of consumers nationwide, enhancing both work and life quality.
20
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.