Where is the fuel tank switch located on the Buick Excelle?

1 Answers
VonRonan
07/30/25 7:10am
The fuel tank switch on the Buick Excelle varies depending on the model: 1. For older models, the fuel cap switch is located between the A and B pillars in the driver's compartment, near the pedals. Press the fuel cap switch to open it. 2. For newer models, simply press lightly around the fuel cap to open it. The Buick Excelle is equipped with: a 1.5L naturally aspirated engine (multi-point fuel injection) paired with an automatic transmission; a 7.0-inch central control screen supporting CarPlay and CarLife; six airbags, tire pressure monitoring, ESP system, and a rearview camera. Dimensions: length 4609mm, width 1798mm, height 1486mm, wheelbase 2640mm.
Was this review help?
18
2
Share
More Forum Discussions

Can Illegal Photography Capture Speeding?

Illegal photography can capture speeding. As long as a vehicle is speeding, it is almost impossible to escape detection. Of course, there are some special circumstances, such as when the captured photos are too blurry to identify the license plate or other vehicle characteristics, or when two license plate numbers appear, which are considered invalid captures and will not be recognized as speeding. However, the probability of such cases is extremely low. Illegal photography can indeed capture speeding. More relevant information is as follows: 1. Speed Measurement: Speed measurement is divided into two types: fixed-point speed measurement and interval speed measurement. Fixed-point speed measurement captures the instantaneous speed of a vehicle, and the instantaneous speed must not exceed the speed limit of that road section. Interval speed measurement calculates the average speed by dividing the distance traveled on the road section by the time taken. If the average speed is higher than the speed limit, it definitely indicates speeding behavior. 2. Note: According to the current speeding violation capture system, the vehicle capture rate can reach 100%, with a recognition time of about 1 second. The daytime recognition rate is over 95%, and the nighttime recognition rate is over 90%. It is applicable to speeds ranging from 5-180km/h.
12
0
Share

What to Do If a Car Is Struck by Lightning While Driving?

The methods to handle a car being struck by lightning while driving are: 1. Immediately turn off all electronic devices inside the car; 2. Wait until the thunderstorm has passed before continuing to drive; 3. Do not immediately exit the car to check its condition. Precautions to take while driving in thunderstorm weather include: 1. Slow down and maintain a safe distance from vehicles in front and behind; 2. Turn on the windshield wipers to maintain good visibility; 3. Set the air conditioning to blow towards the windshield to reduce fogging; 4. Drive at low speed through waterlogged areas; if the water level exceeds the exhaust pipe, find an alternate route; 5. Reduce speed when turning and avoid sudden braking; 6. Turn on fog lights while driving in the rain to make your vehicle more noticeable to other drivers; 7. If the engine takes in water, do not start the vehicle; 8. Do not restart the vehicle after it stalls; 9. Pay attention to the movements of non-motor vehicles and pedestrians and maintain a safe speed.
15
5
Share

How to Use a Charger to Charge a Car Battery?

Using a charger to charge a car battery involves the following method: For a used battery, opt for slow charging, select a 12-volt power source, and choose a low gear to charge the battery slowly. Plug in the charger, turn on the switch, and the battery will begin charging. The charging time should not exceed 12 hours. Charging a car battery is typically the job of the engine. The car's engine drives the generator, which then completes the cycle of charging the car battery. The car's generator produces electricity by continuously running the engine and driving the generator via a belt. Excess electricity is stored in the battery. After turning off the engine, remove the used battery from the car and charge it using a battery charger. Charging steps: 1. First, find a ventilated and shady location. If it's a maintenance-free battery, there's no need to open the cover. For other types, open the vent cover on the battery. If the cover is screwed on, unscrew it in reverse; otherwise, pry it open with a screwdriver, depending on the situation. 2. Attach the charger's red clamp to the battery's positive terminal marked with a plus sign, and the black clamp to the negative terminal marked with a minus sign.
1
5
Share

How Often Should a Car's Refrigerant Be Replenished?

Generally, the refrigerant in a car's air conditioning system needs to be replenished once a year, while a well-functioning air conditioning system may only require a refrigerant top-up every three years or so. Important Notes: Before adding refrigerant to a car's air conditioning system, it's essential to determine whether the system is actually low on refrigerant. There are various reasons why an air conditioner might not cool properly, such as refrigerant leaks, clogged air filters, wear and tear in older systems, or improperly sealed doors and windows. Considerations for Adding Refrigerant: There are two methods for adding refrigerant to an air conditioning system: high-pressure side charging and low-pressure side charging. These are two completely different methods—one involves adding liquid refrigerant, while the other involves adding gas. High-pressure side charging is typically used for initial charging and involves adding liquid refrigerant, which is quicker and safer. Low-pressure side charging involves adding gas refrigerant, which is a slower process and is generally used for topping up the system.
19
3
Share

Will stopping beyond the stop line at a red light result in penalty points?

Stopping with the entire vehicle beyond the stop line at a red light does not incur penalty points; only proceeding further and running the red light will result in penalty points. Additional relevant information is as follows: 1. Running a red light: This refers to the act where motor vehicles, non-motor vehicles, pedestrians, etc., violate traffic signal instructions by crossing the stop line and continuing to move when the red light is on and passage is prohibited. The extended meaning of 'running a red light' is often used to describe actions that go beyond existing rules or violate legal or moral norms. 2. Note: Regardless of the reason, any violation of running a red light will be penalized according to the law. However, the video equipment at intersections is very cautious in collecting information about red-light violations each time, requiring 'three rounds of review.' In other words, to confirm that a vehicle has run a red light, three photos are required as evidence: before the vehicle crosses the line, after crossing the line, and entering the intersection. 'The photo of entering the intersection can clearly show whether the vehicle forcibly passed through during the red light,' explained a traffic officer. The three photos will clearly record the vehicle's movement during the red light.
9
3
Share

Why does the automatic transmission make noise when releasing the foot brake at startup?

There are several reasons for the abnormal noise when releasing the brake during automatic transmission startup: 1. Slow brake release: This noise is mainly caused by releasing the brake too slowly during startup, which is a common issue for many automatic transmission car owners. When the brake pedal is released gradually, the engine already has sufficient power to drive the car forward, but the brake is not fully released. As a result, the moving wheels are restrained by the brake system, naturally causing abnormal noise. So next time, remember to release the brake faster. 2. Brake disc and brake pad sticking together due to rust: This usually happens after driving in rainy weather and then leaving the car unused for several days. The brake disc and brake pad rust and stick together, causing abnormal noise when starting the car again. This can be resolved by applying butter or special lubricating oil to the connection between the brake pad and brake caliper at a repair shop. 3. Metal noise: Many brake pads nowadays are made of semi-metallic materials, containing a large number of metal fibers. Sometimes, metal particles form, producing a harsh sound when stepping on or releasing the brake. This condition usually disappears after driving for a while. If it persists, it may be due to poor manufacturing quality, and it is recommended to replace the brake pads promptly to avoid scratching the brake disc.
15
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.