Where is the fuel tank cap switch of Changan Automobile?

1 Answers
Angelina
07/29/25 12:17pm
The fuel tank cap switch is located under the driver's seat in the main driving compartment. Since it is a mechanical lock, operating the fuel tank cap switch is not very convenient and requires manual operation. In fact, different car models have different designs, and there may be slight variations in the way the fuel tank cap is opened. In the trunk of the car, there is a backup fuel tank switch. By removing the plastic panel on the left side of the trunk, you can access the backup switch for the fuel tank cap. However, this operation should be performed by a professional mechanic at an auto repair shop. When opening the fuel tank cap, it is generally done by lifting it upwards. Therefore, it is important to apply the right amount of force to avoid damaging the operating lever. It is also advisable to prevent children from tampering with it, as a broken operating lever would make it impossible to open the fuel cap. The fuel tank cap refers to the container on the car used for storing gasoline. It is square-shaped, made of stainless steel, and has excellent sealing properties. It has only a small circular opening, about the size of a bottle cap, for easy storage. It is usually located at the rear of the car. In modern cars, the trunk and fuel tank cap can generally be controlled remotely from the driver's compartment.
Was this review help?
8
3
Share
More Forum Discussions

How Far in Advance Does Tesla Notify for Vehicle Pickup?

Notification for vehicle pickup is typically given approximately one week in advance. Below is relevant information: Brand Introduction: Tesla is an American electric vehicle and clean energy company that manufactures and sells electric cars, solar panels, and energy storage systems. Headquartered in Palo Alto, the company was named Tesla Motors by its founder in honor of physicist Nikola Tesla. Logo Meaning: The logo not only represents the initials of inventor Nikola Tesla's name, but also subtly references the company's products. The T-shaped emblem is said to depict the cross-section of an electric motor, with the main body of the letter T representing part of the motor's rotor, while the top secondary line symbolizes a portion of the external stator.
1
1
Share

What is the parking sequence for an automatic transmission car?

Automatic transmission car parking sequence is as follows: 1. Press the foot brake to stop the car. 2. Shift the gear from D (Drive) to N (Neutral). 3. Engage the handbrake and turn off the engine. 4. Release the foot brake, but do not turn off the power (to confirm that the vehicle is completely stationary under the effect of the handbrake). 5. Press the foot brake again and shift the gear from N (Neutral) to P (Parking). 6. Release the foot brake. 7. Turn the key back to the off position, turn off the power, and remove the key. Here is an explanation of the automatic transmission gear positions: 1. P—Parking, the parking gear, also the starting position. When the car is parked and not in use, the gear is in this position, and the wheels are mechanically locked to prevent rolling. 2. R—Reverse, the reverse gear. Used when reversing the car. 3. N—Neutral, the neutral gear. Used for temporary stops (e.g., at a red light). Note that this gear position means neutral, and to prevent the car from rolling on a slope, the brake must be pressed. 4. D—Drive, the forward gear, also known as the driving gear. Used when moving forward.
5
1
Share

What is the actual fuel consumption of the Transit?

The actual fuel consumption of the Transit is 9.3L/100km. Below is the relevant introduction: Introduction to the Transit: The Jiangling Transit is the first independently branded European-style light passenger vehicle launched by Jiangling. It is a reliable, durable, and cost-effective European-style multi-purpose commercial vehicle with upgraded configurations based on the Jiangling-Ford Classic Transit. Advantages of the Transit: The Jiangling Transit features a stylish and dynamic exterior, flexible and convenient handling, continuous powerful performance, comprehensive safety configurations, delivering a brand-new experience of being particularly versatile, fast, excellent, and economical. The Jiangling Transit adopts a car-like interior, which is both fashionable and practical.
2
3
Share

Why does the motorcycle not start and the relay makes noise?

If the circuit breaker makes a beeping sound, the most likely cause is a depleted battery or corrosion on the battery terminals leading to excessive resistance. If the battery is ruled out, check whether the starter relay is faulty. You can directly connect the two terminal posts or the two thick wires of the starter relay. Another possibility is a fault in the starter motor, such as worn carbon brushes or commutators inside the motor, or excessive dirt—cleaning with fine sandpaper may help. The starter motor's coil could also be burnt out, requiring replacement. The electric start of a motorcycle consumes a significant amount of power, while the headlight and horn use much less, so normal operation of the lights and horn does not guarantee sufficient battery power for the electric start. Below is relevant information: Introduction: A relay (English name: relay) is an electrical control device that causes a predetermined step change in the controlled quantity in the electrical output circuit when the input quantity changes to meet specified requirements. It establishes an interactive relationship between the control system (also known as the input circuit) and the controlled system (also known as the output circuit). Typically used in automated control circuits, it functions as an 'automatic switch' that uses a small current to control a larger current. It plays roles such as automatic regulation, safety protection, and circuit switching in electrical circuits. Applications: Relays are automatic switching elements with isolation functions, widely used in remote control, telemetry, communication, automatic control, mechatronics, and power electronic equipment, making them one of the most important control components.
18
0
Share

What is the fuel tank capacity of the Chery X1 in liters?

There are a total of 14 models of the Chery X1, classified as a compact SUV, with a fuel tank capacity of 55 liters. The vehicle is equipped with two types of engines: a 1.3L 84 horsepower L4 and a 1.5L 109 horsepower L4. The transmission options include a 5-speed manual and a 5-speed mechanical automatic, with the intake form being naturally aspirated. During actual refueling, the amount of fuel may exceed the calibrated capacity. This is because the fuel tank capacity specified by the car manufacturer is measured from the bottom of the tank to the safety limit. There is additional space from the safety limit to the tank opening, which is designed to allow for fuel expansion due to temperature increases without causing overflow. If fuel is filled up to the tank opening during refueling, the actual amount of fuel added may exceed the calibrated tank capacity. Maintenance of the fuel tank includes the following: Drain accumulated water and sediment from the tank, and check for any oil leaks at the fuel pipe joints and switches. For fuel tank caps equipped with air valves and steam valves, ensure that the ventilation holes are clear. The filter screen at the fuel filler neck should remain intact to prevent impurities from entering the tank during refueling and clogging the fuel lines. The sealing gasket on the fuel filler cap should also be intact to prevent fuel spillage while driving.
15
0
Share

What are the four wires of the Skoda Superb electric fan?

The four wires of the car engine cooling fan relay are: the ground wire from the temperature control switch, the permanent live wire, the relay output wire, and the ignition live wire. Connection wires of the fan relay: The four wires of the car engine cooling fan relay are: the ground wire from the temperature control switch, the permanent live wire, the relay output wire, and the ignition live wire. Function of the relay: Relays generally have a sensing mechanism (input part) that can reflect certain input variables (such as current, voltage, power, impedance, frequency, temperature, pressure, speed, light, etc.); an actuating mechanism (output part) that can control the "on" and "off" of the controlled circuit; and between the input part and output part of the relay, there is an intermediate mechanism (driving part) that couples and isolates the input, processes functions, and drives the output part.
5
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.