···
Log in / Register

Where is the fuel tank cap switch located on the Tucson?

3 Answers
OPaislee
08/28/25 8:41am
Tucson's fuel tank cap switch is located at the lower left side of the driver's seat, near the door. There is a small handle that you can pull upwards to open it. The Tucson has the following dimensions: length 4545mm, width 1850mm, height 1670mm, with a wheelbase of 2670mm. Its fuel tank capacity is 62 liters and trunk capacity is 488 liters. The Tucson is equipped with a 1.6L turbocharged engine delivering a maximum horsepower of 177PS and peak power at 5500rpm, paired with a 7-speed dual-clutch transmission. It features MacPherson strut front suspension and multi-link independent rear suspension.
Was this review help?
11
4
Share
LeCarson
09/10/25 6:45am
I've been driving the Tucson for many years and know it quite well. The fuel filler door release is usually located on the driver's side, either slightly above the floor or at the lower left corner of the steering wheel - it might be a small lever or button. To operate, simply pull it once and the cap will pop open. If it doesn't respond when pressed, check the vehicle's lock status - try locking and unlocking the car; sometimes a blown fuse or electronic system issue can cause it to stick. Sharing personal experience: I always turn off the engine before refueling - safety first to avoid fire risks. Also, the switch position might vary by model year - older models often have manual levers while newer versions may integrate it into the infotainment settings (just check the manual). If you can't find it, don't panic - you can use your key to manually unlock via the emergency release hole beside the fuel filler door.
Was this review help?
10
3
Share
Expand All
StAlice
10/24/25 7:37am
As a young person who frequently drives for travel, I appreciate the minimalist design of the Tucson. The fuel tank cap switch is usually located on the floor near the left foot, close to the pedals. Just bend down and feel for the small lever, then gently pull to open the cap. If you can't find it, it might be tucked too low or blocked by the footrest—just clear away any obstructions. A quick reminder: always ensure the cap is tightly closed after refueling to prevent fuel odors from escaping, and make sure the car is locked before operating for basic theft prevention. If the switch malfunctions, like the button not working, avoid forcing it—try restarting the vehicle system instead. Before every trip, I check the switch's functionality; it's a good habit to avoid any mid-journey embarrassments.
Was this review help?
4
0
Share
Expand All
More Forum Discussions

What Causes Vibration When Braking?

The reasons for vibration when braking are: 1. Uneven surfaces of the brake disc, hub mounting face, or wheel hub face; 2. Manufacturing tolerances of the brake disc causing brake vibration; 3. Uneven torque between the two-piece disc and hub bolts leading to irregular surfaces. Solutions for vibration when braking include: 1. Grinding rust spots to achieve a flat surface and thoroughly cleaning the wheel hub and steering knuckle contact areas; 2. Selecting high-precision components; 3. Replacing warped parts. Brake pad replacement procedure: 1. Open the engine compartment to check brake fluid level to prevent overflow during replacement; 2. Remove the wheel where the brake is located; 3. Remove caliper bolts and take out old brake pads; 4. Install new brake pads, tighten guide bolts, completing the replacement.
11
2
Share

How to Restore a Car Remote Key That Has Power but Isn't Working?

Due to sealing issues, the interior is often exposed to factors like moisture, dirt, or oxidation, causing the buttons to gradually become less responsive. You need to open the key casing, remove the battery, and then use a cotton swab dipped in alcohol to clean the button contacts on the internal circuit board. The malfunction may be caused by poor contact in the circuit board of the car remote. However, since the solder joints are very small, it is recommended to take it to a professional electronics repair shop or a mobile phone repair service. Electronic signal interference from devices like mobile phones or signal blockers (such as transformers) in the vicinity of the owner or the vehicle can also cause the remote to malfunction.
6
2
Share

How to Remove Car Rust Spots?

First, try using a clay bar. Wet the clay bar and vigorously rub it on the rust spots on the car body, then rinse with clean water. If that doesn't work, you can use a specialized iron remover spray on the rust spots and then rinse with water. If the above methods don't solve the problem, you can lightly polish the paint surface to remove the rust spots. If after rain or when road sewage splashes onto the car and isn't washed off in time, the iron elements in the dried sewage can oxidize and cause rust spots. In such cases, after washing the car, you can use a clay bar with water to wipe them off, or spray and wipe with a tar remover for easy cleaning.
2
3
Share

What to Do When the Tail Lights Remain On After the Car is Turned Off?

The brake light switch is generally located above the brake pedal. First, remove the protective panel, which is the base plate above the brake, clutch, and accelerator pedals. After removing the panel, you will see the brake light switch above the brake pedal. The switch is a twist-lock type and can be removed by turning it counterclockwise. To install the new brake light switch, insert it into the twist-lock hole and turn it clockwise to secure it. Reinstall the protective panel in the reverse order of removal. After replacement, test the brake system to ensure the brake lights are functioning properly.
18
2
Share

How to Use Car Key Function Buttons?

Arming the system prevents car theft by triggering an alarm if the vehicle is tampered with. Some cars automatically arm the system, requiring you to unlock and disarm before starting the engine. The 'Find My Car' button helps locate your vehicle when you forget its exact parking spot or in areas with many similar cars. Pressing it makes the car respond audibly. This feature works within a 10-meter radius; beyond that, it becomes ineffective. The 'Keyless Start' function allows emergency engine activation without the physical key when it's not available.
3
4
Share

How to Open the Car Door When the Key Is Lost?

When the primary key is lost, the spare key can come in handy. You can either go back to get it yourself or ask a family member to bring the spare key to you. Hiring a locksmith is a last resort. Make sure to choose a qualified and reputable locksmith company. Nowadays, most 4S shops offer after-sales rescue services. Simply call them and wait for the rescue team to arrive. If you are in a remote location where the above methods are difficult to implement, you may have to resort to breaking the car window to open the door. Remove the window seal, then use a wire or thin string to lower it through the window gap near the door lock position. Loop it around the door latch and pull upward to open the door.
8
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.