Where is the fuel pump relay of BYD F3 located?

1 Answers
DelLola
07/29/25 9:17pm
BYD F3 fuel pump relay is located on the wiring harness assembly. The wiring harness assembly is positioned under the steering wheel, with a small storage compartment on the left side. Behind this storage compartment, the wiring harness assembly sequentially contains the fuel pump relay, window relay, vacant slot, rear defroster relay, ignition relay, and flasher relay mounting bracket. A relay is an automatic switch that uses a smaller current to control a larger one, functioning as an electronic control device with both control and controlled systems. It is commonly used in automatic control circuits to perform roles such as automatic regulation, safety protection, and circuit switching. The BYD F3 series is equipped with a 1.5L inline 4-cylinder naturally aspirated engine, paired with either a 5-speed manual or 6-speed dual-clutch transmission, delivering a maximum power of 80KW and a maximum torque of 145NM.
Was this review help?
2
4
Share
More Forum Discussions

What can be extracted from a three-way catalytic converter?

A three-way catalytic converter can extract platinum (Pt), rhodium (Rh), and palladium (Pd), which are platinum group precious metals. The function of a three-way catalytic converter is to react with the exhaust gases emitted by a car, catalyzing or altering the nature of harmful emissions, thereby reducing their pollution. Methods for extracting precious metals from a three-way catalytic converter: Grind the catalyst inside the three-way catalytic converter into powder, as the precious metals are coated as a layer of catalyst inside; burn the powdered catalyst at high temperatures; add a sodium borohydride aqueous solution and boil to 100 degrees Celsius, then add a sodium chlorite hydrochloric acid solution; maintain the temperature around 100 degrees Celsius; after 3 hours, filter; add a 10% HCl aqueous solution for acid washing and water washing, keeping the temperature around 100 degrees Celsius. After separation, platinum group metals can be obtained. Precautions for using a three-way catalytic converter: Do not use leaded gasoline; avoid prolonged idling (open-loop control state); avoid sudden changes in engine speed; do not set the ignition timing too late; do not pull out the high-voltage wire for extended periods to test for sparks; when measuring cylinder pressure, disconnect the central control connector of the fuel pump to stop the injector from spraying fuel into the cylinder; if any cylinder is found to be malfunctioning, stop the vehicle promptly to inspect and rectify the issue, etc.
19
2
Share

What is the method for matching the sunroof of the 2018 Volkswagen Lamando?

The method for matching the sunroof of the 2018 Volkswagen Lamando is: 1. Turn on the ignition and hold the sunroof switch in the position with a dotted line; 2. Turn off the ignition and wait for the sunroof to move back and forth twice; 3. Open and close the sunroof, then turn the switch to the closed position; 4. Turn on the ignition again and open the sunroof to complete the process. Maintenance methods for car sunroofs include: 1. Regularly check the condition of the sunroof guide rails; 2. Reduce the frequency of sunroof usage; 3. Do not open the sunroof when the car is cold in winter; 4. Check the drainage status of the sunroof before the rainy season. Types of car sunroofs: 1. Divided by driving method into manual and electric; 2. Divided by panel material into glass panel, metal panel, and composite material panel; 3. Divided by structure into tilt-up, sliding, built-in, and convertible. Components of a car sunroof: 1. Sliding mechanism; 2. Driving mechanism; 3. Switch button; 4. Control system.
12
1
Share

What is the reason for the buzzing noise from the seat belt in the car's B-pillar?

The reason for the buzzing noise from the seat belt in the car's B-pillar is the friction between the seat belt buckle and the seat. The solutions for the buzzing noise from the seat belt in the car's B-pillar are: 1. Adjust the height of the car seat and observe whether the noise disappears during the adjustment process; 2. Add a buffer material between the seat and the seat belt buckle. The correct way to fasten a car seat belt is: the shoulder strap should cross the chest, the waist belt should fit snugly against the hip bones, and the buckle should be securely fastened. The function of the car seat belt is: when the vehicle collides or emergency braking is applied, the pre-tensioning device will instantly retract, tightening the slack seat belt and firmly securing the occupant to the seat to prevent secondary collisions.
6
4
Share

Should the ESP Vehicle Stability System Be Turned On?

ESP vehicle stability system should be turned on. The ESP system is a general term for systems or programs that enhance vehicle handling performance while effectively preventing loss of control when the vehicle reaches its dynamic limits. The ESP system includes functions such as electronic brake force distribution, anti-lock braking system, traction control system, and vehicle dynamic control system. The principle of the ESP system is as follows: through the ABS electronic control unit, based on signals from the wheel speed sensors, the electronic control unit calculates and analyzes to determine the wheel slip rate and vehicle speed. It then adjusts the wheel slip rate by controlling the throttle opening and brake pressure.
15
2
Share

What is the reason for the sudden dimming of the Envision dashboard lights?

The reason for the sudden dimming of the Envision dashboard lights is due to a slight battery drain. Taking the 2021 Envision as an example, it is a mid-size SUV with body dimensions of: length 4694mm, width 1839mm, height 1686mm, wheelbase of 2750mm, and a body weight of 1610kg. The 2021 Envision features a front suspension with MacPherson independent suspension and a rear suspension with multi-link independent suspension. It is equipped with a 1.5T turbocharged engine, delivering a maximum horsepower of 169PS, a maximum torque of 250Nm, and a maximum power of 124kW, paired with a 7-speed dual-clutch transmission.
1
3
Share

How to set the automatic downward tilt of the rearview mirror when reversing in Audi A6L?

Audi A6L's method for setting the automatic downward tilt of the rearview mirror when reversing is: 1. Turn on the car's power without starting the engine; 2. Set the memory seat; 3. Select the rearview mirror on the side you want to set and press the rearview mirror adjustment selection button; 4. Step on the brake and shift to R gear; 5. Press and hold the seat memory key; 6. Step on the brake and shift to P gear, then press the rearview mirror adjustment selection button once more to complete the setup. Taking the 2021 Audi A6L as an example, it is a mid-to-large-sized car with body dimensions of: length 5038mm, width 1886mm, height 1475mm, wheelbase of 3024mm, minimum ground clearance of 117mm, and a body weight of 1800kg.
16
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.