Where is the fuel pump relay located in the older Focus models?

1 Answers
VanAdelyn
07/29/25 3:58pm
The fuel pump relay in older Focus models is installed inside the engine compartment fuse box. Here is some relevant information about the Focus: 1. Overview: The Changan Ford Focus was launched at the Guangzhou Auto Show on November 20, 2020. The Changan Ford Focus family introduced a total of eight models, including seven variants of the 2021 Ford Focus in both sedan and hatchback versions. 2. Other details: The wheelbase is 2705mm. Fuel consumption ranges from 5.5 to 5.7L/100km. Standard seating capacity is 5. Top speed is 215km/h. Acceleration time is 8.9s. The drivetrain is front-engine, front-wheel drive. Curb weight ranges from 1245kg to 1411kg. The suspension system features full independent suspension.
Was this review help?
10
0
Share
More Forum Discussions

How to Maintain a Car in Winter?

Here are the methods for winter car maintenance: 1. Wiper Blades and Windshield: Due to weather conditions, wiper blades often stick to the windshield in winter. Do not force them off. Instead, turn on the car's air conditioning, set it to blow air towards the windshield to raise its temperature. This also helps check if the heating system is functioning properly. Regularly clean the heating system to ensure good air quality inside the car. 2. Body and Chassis: The car's exterior inevitably gets damaged while driving, and even when parked. In winter, with rain and snow, the car's exterior is prone to corrosion. Roads are often salted to quickly melt snow, and the tires can splash salt-laden snow water onto the chassis, causing rust. Therefore, before winter arrives, thoroughly inspect the car's body, repair any scratches promptly, and apply wax in early winter to protect the paint. Waxed surfaces are less prone to moisture, and ice formation on the body is significantly reduced. Also, perform anti-rust maintenance on the vehicle's chassis to extend its lifespan.
8
0
Share

How to Remove the Spark Plugs on a Haval M6?

Steps for replacing the spark plugs on a Haval M6: Open the engine hood, lift off the plastic engine cover, and remove the high-voltage distributor wires. Mark each cylinder's position to avoid confusion. Use a spark plug socket to remove the spark plugs one by one. While removing them, check for any external debris like leaves or dust and ensure everything is cleaned thoroughly. Place the new spark plug into the spark plug hole, hand-tighten it a few turns, and then use the socket to tighten it further. Reinstall the high-voltage distributor wires in the correct firing order, then snap the cover back into place. If a spark plug is damaged, it can directly cause issues such as electrical leakage in the ignition system, increased fuel consumption, reduced power, and most notably, difficulty starting the engine, affecting the vehicle's normal operation. Severe spark plug erosion—indicated by pitting, damage, or melted electrodes—means the spark plug is worn out and should be replaced.
3
4
Share

What is the fuel consumption of the Benelli 752s?

The fuel consumption of the Benelli 752s is approximately 5 liters per 100 kilometers. Here is an extended introduction: 1. Factors affecting fuel consumption: There are many objective factors that can influence fuel consumption. For example, individual driving habits, usual road conditions, vehicle load, etc., can all significantly impact a car's fuel consumption. 2. Power: It is equipped with a twin-cylinder water-cooled electronic fuel injection engine, with a compression ratio of 11.5:1 and an actual displacement of 745cc. It is matched with a slipper clutch, with a maximum power of 56KW (76Ps)/8000rpm and a top speed of 200km/h. 3. Tires: The front tire model is 120/70-17, and the rear tire is 180/55-17. 4. Body dimensions: The wheelbase is 1460mm, the fuel tank capacity is 14.5L, the minimum ground clearance is 180mm, and the curb weight is 228kg.
19
3
Share

How many liters of engine oil does the Mercedes-Benz A200 require?

The Mercedes-Benz A200 requires approximately 6.1 liters of engine oil. Below is some relevant information about the Mercedes-Benz A200: 1. Engine oil specification: The vehicle uses SM-grade 5W30 fully synthetic engine oil. This model does not have a traditional dipstick; instead, the oil level is checked via the central display screen. After adding oil, start the vehicle and then turn it off. Wait for 3 minutes before checking the oil level. When changing the oil, it is also necessary to replace the oil filter. The new oil filter initially contains no oil, so starting the vehicle allows oil to flow into the filter. 2. Fuel consumption: Insufficient oil can lead to increased fuel consumption. Impact point: When the crankshaft journal moves to the bottom dead center, it may come into contact with the oil, creating resistance that affects normal operation. Conversely, too little oil is also problematic as it cannot provide sufficient lubrication, leading to accelerated wear of internal engine components and potential engine damage. Therefore, it is crucial to maintain the oil level within the specified range.
7
5
Share

How to Check Where a Vehicle Has Arrived with the VIN?

With the Vehicle Identification Number (VIN), you can use positioning software to check the current location of the vehicle. Below is relevant information about the VIN: 1. Definition: The Vehicle Identification Number, abbreviated as VIN, is a unique set of seventeen letters or numbers used on automobiles to identify the manufacturer, engine, chassis number, and other specifications. 2. Manufacturer: The first three digits of the VIN are known as the World Manufacturer Identifier (WMI), used to identify the manufacturer's name and country of origin. For manufacturers producing fewer than 500 vehicles annually, the third digit of the VIN will be a '9', and digits 12-14 will serve as the second part of the identification. 3. Plate Location: Except for trailers and motorcycles, the identification plate should be fixed on the door hinge pillar, door lock pillar, or one of the door edges adjacent to the door lock pillar, close to the driver's seat.
18
3
Share

Why Was the Toyota Prius Discontinued?

At that time, domestic production of the Prius was extremely limited, with only a few dozen units manufactured each month. Toyota was unwilling to use domestically produced hybrid core components, opting instead for imported parts, which significantly increased costs—nearly double that of conventional fuel-powered vehicles, approaching the price range of mid-level models. Factors such as low production volume, poor sales performance, lack of subsidies, and high pricing ultimately led to the discontinuation of the Prius. Below are some relevant details: 1. Vehicle Overview: The Toyota Prius, launched by Toyota Motor Corporation in 1997, was the world's first mass-produced hybrid vehicle. By 2001, it was sold in over 40 countries and regions, with Japan and North America being its largest markets. 2. Design Philosophy: Long before the energy crisis and environmental issues became prominent, Toyota had the foresight to incorporate hybrid technology into its long-term development plans. After dedicating over 40 years of effort, the Prius was the first to perfectly execute avant-garde design concepts with future-oriented craftsmanship and was ahead of its time in incorporating a series of highly intelligent technologies.
5
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.