···
Log in / Register

Where is the fuel filler switch on the Haval H6?

4 Answers
SanDakota
09/05/25 7:12am

The Haval H6 does not have a separate fuel filler switch. Its fuel tank cap is located on the left side of the vehicle body and can be opened by pressing lightly when the central locking is unlocked. If the fuel tank cap cannot be opened, you can start from the trunk. First, remove the trim panel covering the fuel tank in the trunk to see the locking mechanism of the fuel tank cap, as well as the fuel tank cap cable for remote operation. Simply pull the cable to open the fuel tank cap. Taking the 2021 Haval H6 third-generation 2.0T automatic two-wheel drive Max as an example: its length, width, and height are 4653mm, 1886mm, and 1730mm respectively, with a wheelbase of 2738mm. It is equipped with a 2.0T turbocharged engine, with a maximum power of 155kw and a maximum torque of 325nm.

Was this review help?
2
4
Share
SanLilah
09/17/25 7:26am

I remember when I was refueling my Haval H6, the fuel tank release switch was located near the left foot area of the driver's seat. There was a small lever on the floor - a gentle pull would open the fuel filler cap. When I first started driving, I thought it would be a button on the door panel, but later realized this design is actually for safety to prevent accidental activation. Always remember to park and turn off the engine before operating it - never try to locate it while driving. Before refueling, check if the fuel cap seal has deteriorated as it may affect fuel efficiency. After two years of use, my lever occasionally gets slightly stiff, so I apply some lubricant. Overall, the position becomes intuitive once you're familiar with it - new drivers just need some practice to get used to it.

Was this review help?
13
5
Share
Expand All
OMaria
10/31/25 7:57am

When I first started driving this car, I was quite troubled by finding the fuel filler switch. I fumbled around near the left foot pedal in the driver's seat and finally found a slender lever. Giving it a firm pull, the fuel tank cap popped open effortlessly. Later, I made it a habit to check the position diagram in the manual when parking to avoid panic. When refueling, make sure the nozzle is properly aligned to avoid splashing on clothes—safety first. The H6's design is quite user-friendly, with the lever positioned low for easy operation. For older vehicles, the lever might loosen, so it's advisable to have the wiring checked regularly.

Was this review help?
4
0
Share
Expand All
JaceDella
12/14/25 8:05am

The fuel filler switch of the Haval H6 is located on the floor near the driver's side door, featuring a simple lever mechanism. Simply pull it to open the fuel tank cap. I've noticed slight variations across model years, with some levers being slightly shorter, but the position remains largely unchanged. Remember to turn off the engine and park before refueling. Routine maintenance includes cleaning dust around the lever to prolong its service life. Safety tip: Always ensure the switch functions properly before inserting the fuel nozzle to prevent fuel leakage.

Was this review help?
7
3
Share
Expand All
More Forum Discussions

How to Turn On Front and Rear Fog Lights?

Front and rear fog lights can be turned on as follows: 1. Lever-type fog lights: Rotate the lever upwards one notch to turn on the front fog lights, and rotate two notches to turn on both front and rear fog lights simultaneously. 2. Knob-type fog lights: Pull the knob out one position to turn on the front fog lights, and pull it out another position to turn on both front and rear fog lights at the same time. Additional information: 1. Purpose of fog lights: Installed at the front and rear of the vehicle, fog lights enhance visibility for the driver and other road users. 2. When to use fog lights: They must be turned on during heavy fog or rain when visibility is low to prevent rear-end collisions.
12
4
Share

Where is the fuse box located in the BMW 3 Series?

The BMW 3 Series has two fuse boxes, one located on the side of the trunk and the other in the engine compartment in front of the passenger seat. Below are the detailed specifications of the BMW 3 Series: 1. Body dimensions: The vehicle weighs 1465 kg, with length, width, and height measuring 4734mm, 1811mm, and 1455mm respectively. 2. Powertrain: The long-wheelbase version of the BMW 3 Series is equipped with the new B-series 2.0T engine, delivering 184 horsepower, the same as the current 320i/Li, but the tail badge has been changed to 325Li. 3. Transmission: It is paired with an 8-speed automatic transmission. Additionally, improvements in lightweight design, thermal energy management, and fuel efficiency optimization contribute to the vehicle's power output.
4
3
Share

Do You Need to Press the Brake to Shift Gears in an Automatic Transmission?

Automatic transmissions do not require pressing the brake to shift gears. Here is an introduction to the gears of an automatic transmission car: 1. All gears: The gears of an automatic transmission include P, R, N, D, 2 or S, L or 1. 2. Parking gear: P stands for Parking gear, also known as the Parking position. 3. Other gears: R stands for Reverse, N stands for Neutral, D stands for Drive, also known as the Driving gear. 4. Sport mode: S or 2 represents Sport mode. 5. Low gear: L or 1 stands for Low gear, also known as 1st gear. Here is additional information on driving an automatic transmission car: 1. General situation: When driving, unless there are special requirements, do not repeatedly move the gear lever between D, 3, 2, 1, etc. 2. Damage: When starting an automatic transmission car, ensure the gear is in P or N position, otherwise it may damage the transmission. 3. Reversing: When reversing an automatic transmission car, ensure the vehicle is completely stopped before shifting into R gear.
5
5
Share

What Causes Engine Shaking When Starting an Automatic Car?

Here are the reasons for engine shaking when starting an automatic car: 1. Throttle: A dirty throttle causes uneven airflow, leading to shaking. 2. Fuel system: Poor fuel flow results in inadequate fuel supply at low throttle, causing uneven cylinder operation and shaking. 3. Transmission: Abnormal transmission operation. 4. High-voltage wires: Broken or burnt high-voltage wires or spark plug failure can cause cylinders to misfire, leading to unstable engine operation and shaking. 5. Battery voltage: Whether the battery voltage is within the specified range. Below are additional details on related causes: 1. Cause: The most common reason for car shaking is a dirty throttle or excessive carbon buildup in the fuel injectors. 2. Engine carbon buildup: When there is excessive carbon buildup inside the engine, the gasoline sprayed by the cold-start injector is largely absorbed by the carbon deposits, resulting in an overly lean air-fuel mixture during cold starts and making it difficult to start.
8
5
Share

Which Turn Signal to Use When Exiting a Ramp?

When exiting a ramp, you should turn on the right turn signal. Below is an introduction about exiting a ramp: 1. Exiting a ramp: (1) When exiting a highway via a ramp, pay attention to the intersection warning signs, divert your vehicle from the main lane into the deceleration lane to slow down, and then enter the general road via the ramp. (2) When leaving the ramp, turn on the right turn signal. 2. Entering a ramp: (1) On the ramp, when entering the highway, you need to quickly increase your speed. However, do not exceed the speed limit indicated by the signs. Overtaking, making U-turns, stopping, and reversing are not allowed on the ramp. (2) After driving from the ramp into the highway acceleration lane, you may or may not turn on the left turn signal, quickly increase your speed to over 60 km/h, and carefully observe the traffic on the lane to choose the right moment to merge into the driving lane. Emergency braking or stopping in the acceleration lane is not allowed. When the driving lane is sparsely populated with vehicles, you can merge into the driving lane after normal driving; if vehicles on the highway are following closely, control your speed and merge into the driving lane only after all vehicles have passed.
15
1
Share

Is starting at 3000 RPM harmful to a CVT transmission?

Starting a CVT transmission at 3000 RPM can cause certain damage to the transmission and clutch plates, and it is not recommended to drive this way. There are three common types of automatic transmissions in automatic cars: dual-clutch transmissions, CVT transmissions, and AT transmissions. The specific details are as follows: 1. Dual-clutch transmission: (1) It connects to the engine via clutch plates. The structure of a dual-clutch transmission is similar to that of a manual transmission, except that it has an additional set of clutches and a shift control mechanism. (2) One set of clutches in a dual-clutch transmission controls the odd-numbered gears, while the other set controls the even-numbered gears. (3) Dual-clutch transmissions offer fast shifting speeds and relatively high transmission efficiency. 2. AT transmission: (1) It connects to the engine via a torque converter. (2) AT transmissions are the most mature and widely used automatic transmissions, featuring a relatively complex structure. (3) AT transmissions contain many planetary gears, which are responsible for gear shifting and torque conversion. 3. CVT transmission: (1) The internal structure is relatively simple, consisting of only two pulleys and a steel belt. (2) The steel belt in a CVT transmission can move along the pulleys, enabling gear shifting and torque conversion. (3) CVT transmissions provide smooth shifting and good reliability and durability.
7
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.