Where is the fuel filler button on the Envision?

2 Answers
OMarley
07/24/25 11:05pm
The Envision does not have a fuel filler button. Simply shift to P (Park) and press the outer side of the fuel tank to open it. The Envision is a midsize SUV under SAIC-GM Buick. Taking the 2021 Envision 532T FWD Leading model as an example, its body dimensions are 4694mm in length, 1839mm in width, and 1686mm in height, with a wheelbase of 2750mm. The vehicle adopts a 5-door, 5-seat configuration, with a fuel tank capacity of 66 liters and a curb weight of 1610kg. In terms of power, the 2021 Envision 532T FWD Leading model is equipped with a 1.5L inline 4-cylinder turbocharged engine featuring an aluminum alloy structure, delivering a maximum power of 124kW and a maximum torque of 250Nm, paired with a 7-speed dual-clutch transmission.
Was this review help?
10
5
Share
OHolden
08/10/25 3:15pm
I've driven several cars before, including SUVs like the Envision. The fuel filler release button is usually located on the floor to the left of the driver's seat. You can see a small lever or button by looking down and bending over. To operate it, you need to stop the engine first before pulling it to avoid damaging the fuel tank cap. I remember when I first drove a new car, I didn't know its location and searched around the dashboard for a long time, only to find it hidden at my feet. But Buick designed it this way to prevent accidental touches—safety first. Always check if the fuel tank cap is properly locked before refueling to avoid fuel leakage. Regularly cleaning the dust under your feet makes it easier to locate. If you encounter any issues, refer to the user manual—it contains detailed illustrations showing the location and usage steps.
Was this review help?
18
2
Share
Expand All
More Forum Discussions

What is the Basic Working Principle of an Oscilloscope?

The working principle of an oscilloscope involves using a narrow electron beam composed of high-speed electrons to strike a screen coated with fluorescent material, producing a tiny light spot. Under the influence of the measured signal, the electron beam appears to draw a curve representing the instantaneous value changes of the signal on the screen. With an oscilloscope, users can observe various amplitude waveforms of the same signal changing over time, as well as measure various parameters such as voltage, current, frequency, phase difference, and amplitude modulation. A standard oscilloscope consists of five basic components: Display circuit, vertical (Y-axis) amplification circuit, horizontal (X-axis) amplification circuit, scanning and synchronization circuit, and power supply circuit—these form the functional principle of a general oscilloscope.
4
5
Share

How to Reset the Maintenance Light on MG MG6?

The method to reset the maintenance light on MG MG6 is: 1. Turn on the ignition switch, hold down the reset button 5 with one hand, and turn off the ignition switch with the other hand; 2. Keep holding the reset button 5 without releasing until the clock and mileage on the dashboard completely disappear (the dashboard should show no display, black screen), then release the button. Taking the 2020 MG MG6 as an example, its body dimensions are: length 4704mm, width 1848mm, height 1466mm, with a wheelbase of 2715mm. The 2020 MG MG6 features a front suspension type of MacPherson independent suspension and a rear suspension type of multi-link independent suspension.
6
5
Share

What causes jerking and fuel cut-off when accelerating suddenly?

The reasons for jerking and fuel cut-off when accelerating suddenly are as follows: There may be three main causes: 1. Excessive carbon deposits in the throttle body, fuel injectors, or intake manifold: Many malfunctions are caused by carbon deposits, and some vehicles may experience jerking due to this issue. It is recommended to regularly clean carbon deposits. 2. Poor fuel quality: This leads to incomplete combustion, and qualified fuel should be used instead. 3. Faulty spark plugs, ignition coils, etc., causing misfires. It is necessary to visit a repair shop for inspection and timely repairs to avoid further safety hazards.
16
0
Share

Where is the ABS pump located in a car?

The ABS pump is located near the firewall in the car's engine compartment. The working principle of the ABS pump is: relying on highly sensitive wheel speed sensors installed on each wheel and the vehicle's speed sensor, under computer control, when emergency braking is detected and a wheel is about to lock up, the computer immediately commands the pressure regulator to release pressure from that wheel's brake caliper, allowing the wheel to resume rotation. The ABS pump, also known as the Anti-lock Braking System, features anti-skid and anti-lock characteristics. Its working process involves a cycle of locking and releasing, keeping the vehicle in a state of near-lock rolling, effectively overcoming issues like deviation, side-slip, and fishtailing during emergency braking, and preventing loss of vehicle control.
17
0
Share

Does the Roewe i5 comply with the China VI emission standard?

Roewe i5 complies with the China VI emission standard. The China VI standard, also known as the National Sixth Stage Emission Standard for Motor Vehicles, is established to prevent environmental pollution caused by exhaust emissions from compression-ignition and gas-fueled spark-ignition engine vehicles, protect the ecological environment, and safeguard human health. The Roewe i5 is a high-performance internet-connected mid-size sedan under the Roewe brand, with dimensions of 4607mm in length, 1818mm in width, and 1489mm in height, and a wheelbase of 2680mm. The Roewe i5 features a MacPherson strut front suspension and a torsion beam rear suspension. It is equipped with a 1.5L naturally aspirated engine, delivering a maximum power of 88kW and a maximum torque of 150Nm.
5
0
Share

What Causes Engine Vibration in the Hyundai Elantra?

The reason for engine vibration in the Hyundai Elantra is: severe carbon buildup or a dirty air filter, and it is recommended to clean and replace them promptly. The engine is the core part of the powertrain, with the cylinder as its main component, and it serves as the power source for the entire vehicle. Taking the 2020 Hyundai Elantra as an example, in terms of suspension, the front suspension is a MacPherson strut independent suspension, and the rear suspension is a torsion beam non-independent suspension. The 2020 Hyundai Elantra is a compact car with body dimensions of: length 4610mm, width 1800mm, height 1450mm, a wheelbase of 2700mm, and a curb weight of 1319kg.
19
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.