Where is the fuel consumption displayed on the Mercedes-Benz S350?

What to do if the Toyota Corolla has valve oil leakage?

The solutions for valve oil leakage in Toyota Corolla are as follows: 1. It is necessary to remove the timing chain cover and engine valve cover, then clean and apply sealant before installation. Additionally, replacing the rubber ring of the crankshaft position sensor in your vehicle will solve the problem. 2. If the oil at the crankshaft position sensor area forms droplets, it is recommended to replace the seal ring of the crankshaft position sensor as well. These repairs do not require removing the engine, and the repair time will take one day because the removed parts need to be thoroughly cleaned. The parts that need to be replaced include: valve cover gasket, five seal rings, timing tensioner gasket, and sealant.

15

5

Share

What to Do When the Battery of the Tiguan Runs Out of Power?

When taking the Volkswagen Tiguan to a 4S shop or maintenance shop each time, you can use a voltmeter to measure the battery voltage. When it approaches a dangerous value, you can directly replace the battery to avoid embarrassing situations at critical moments. If the battery runs out of power on the road, you can find another car to help jump-start it. The jump-start methods are as follows: 1. Push-start: Push-starting is the most familiar and effective emergency starting method, but it is a last resort and should not be used frequently because it can cause certain damage to the engine and clutch, especially for automatic transmission vehicles, which should avoid using this method to start. 2. Towing-start: The method and principle of towing-start are similar to push-start, but using a towing vehicle is often more labor-saving and convenient. When implementing this method, use a tow rope of appropriate length and secure both ends firmly. Before towing, the drivers of the front and rear vehicles should agree on communication signals, such as honking or gesturing to indicate starting and stopping, to ensure coordinated cooperation. 3. Jump-start: If you encounter a situation where there is another vehicle accompanying you and equipped with jumper cables, you can also use the battery jump-start method to start the vehicle. First, bring the two vehicles close enough until the jumper cables can connect the positive and negative terminals of the two batteries. Ensure that the two vehicles do not touch each other, and only use cables with sufficient load-bearing capacity and insulated outer sheaths.

3

2

Share

Why does the car turn signal flash quickly?

Reasons for excessively fast turn signal flashing: Burned-out turn signal; Poor contact in the turn signal; Inconsistent power or model of the turn signal bulb; Faulty bulb control relay, etc. Below is relevant information about turn signals: 1. Introduction: The turn signal is an important indicator light that activates when a motor vehicle turns, alerting surrounding vehicles and pedestrians. The turn signal tube uses a xenon tube, controlled by a single-chip circuit, with alternating left-right strobe operation. Turn signals employ flashers to achieve light blinking, mainly categorized into resistance-wire type, capacitor type, and electronic type. 2. Structural Principle: The resistance-wire type can be further divided into thermal-wire type (electrothermal) and vane type (spring-action), while the electronic type includes hybrid (relay with contacts and electronic components) and fully electronic (no relay). For example, the spring-action flasher utilizes the thermal effect of current, using expansion and contraction as the driving force to create sudden movement in the spring plate, thereby connecting and disconnecting contacts to achieve light blinking.

2

3

Share

How to Remove the Headlights of a Fit?

Locate a cover behind the headlight, twist it open, and you will see the bulb. Use your fingers to unscrew the bulb from its fixed clip to remove it. More details about the Fit are as follows: 1. The Honda Fit is one of the global strategic models following the Accord and Civic. While maintaining consistent high quality and reliability, it is designed to meet the highest global standards in design, space, safety, handling, fuel efficiency, and practicality, reaffirming its comprehensive leading position in this segment. 2. On August 11, 2016, the 2016 Fit Cool Play edition was launched, adding two sunroof versions. On January 11, 2018, the GAC Honda New Fit Sport series was released, retaining its core product values—featuring the 'Exciting-H-Design' overall design concept, the 'Earth Dreams Technology' engine (1.5L direct-injection DOHC-i-VTEC engine and new CVT continuously variable transmission), and the Idle-stop engine energy-saving automatic start-stop system, among ten other innovative technologies.

11

5

Share

How Often Should Motorcycles Be Inspected Under the New Regulations?

Motorcycles within four years of purchase must be inspected every two years, while those over four years old require annual inspections. Below is relevant information about vehicle inspections: 1. Required documents for inspection: Bring the vehicle registration certificate, compulsory traffic accident liability insurance policy, the inspector's ID card, a triangular warning sign, and a fire extinguisher. A copy of the insurance policy must be submitted during the inspection, which will be retained by the inspection agency. 2. Inspection process: Drive the vehicle to the inspection station for an exterior check, fill out the motor vehicle exterior registration form with the staff, pay fees and log information, undergo online vehicle testing, and collect and affix the inspection compliance label to the upper right corner of the front windshield. 3. Inspection cost: Approximately 200 yuan.

14

1

Share

What to Do When the Water-Fuel Separator Light Comes On?

When the water-fuel separator light comes on, you can open the drain valve under the separator's reservoir to release the accumulated water. Below are detailed explanations about the water-fuel separator: 1. Function: The water-fuel separator is designed to separate water from fuel before it enters the fuel injection pump, utilizing the difference in gravity between fuel and water. 2. Reason for the Light: If the water-fuel separator warning light remains on, it is usually not a component issue. After prolonged use, water accumulates inside the separator, and when it reaches a certain level, the indicator light will illuminate. 3. Troubleshooting: If the light stays on after draining the water from the separator's reservoir, the issue might lie with the water-fuel separator sensor. Use a multimeter to check the sensor's voltage, which should normally be 12V and 5V. If the readings are abnormal and after confirming that it's not due to wiring issues or poor contact, replace the water-fuel separator sensor.

2

5

Share

Where is the fuel consumption displayed on the Mercedes-Benz S350?

What to do if the Toyota Corolla has valve oil leakage?

What to Do When the Battery of the Tiguan Runs Out of Power?

Why does the car turn signal flash quickly?

How to Remove the Headlights of a Fit?

How Often Should Motorcycles Be Inspected Under the New Regulations?

What to Do When the Water-Fuel Separator Light Comes On?

Which tire does not rotate when the car turns right?

Has the oil dilution issue in the CR-V been resolved?

Does the Original Valve Need to Be Replaced?

Which Fire Extinguisher to Use for a Car Fire?