···
Log in / Register

Where is the Ford sunroof drain located?

4 Answers
JaxsonFitz
07/29/25 11:12am

Ford sunroof drains are located at the front edge of the sunroof. Here are some details about vehicle drainage outlets: 1. Door drainage outlets: These are often blocked when sound insulation is installed, preventing rainwater from draining out of the door panels. Over time, this can lead to door corrosion and rust. With increasing electrical components in doors, this may also cause circuit shorts. 2. Sunroof drainage outlets: Many people don't realize sunroofs aren't completely sealed - there are four drainage holes around the sunroof. When clogged, water may leak into the headliner or even the cabin. Regular cleaning of sunroof drains is essential. 3. Engine compartment drainage: This outlet below the windshield directs rainwater under the vehicle, preventing it from entering the engine bay.

Was this review help?
9
0
Share
AndersonLee
08/13/25 5:54pm

As a seasoned Ford driver with several years of experience, I can say that the sunroof drainage outlets are mainly located at the four corners of the roof. For specific Ford models like the Focus or Mondeo, the front drainage outlets are near the door gaps by the A-pillars, above the front wheel arches, while the rear outlets are along the cabin edges near the rear windshield or below the C-pillars. These areas are prone to blockage by leaves or dust, causing rainwater to seep into the car, soaking the carpets or corroding the wiring, which poses significant safety risks. I recommend checking and cleaning them every six months using a soft brush or compressed air to remove debris and prevent leaks during heavy rain. I’ve personally experienced blockages and was lucky to address them in time—otherwise, the cost of repairing the interior would have been high, not to mention the annoyance of impaired visibility while driving. When parking, try to avoid spots under trees to minimize blockage risks.

Was this review help?
17
0
Share
Expand All
StellaMarie
10/08/25 2:56am

As an automotive enthusiast, I have carefully studied Ford's drainage port design, which is very well concealed. For sunroofs, the drainage ports are typically located at the four corners of the sunroof frame. Specifically for Ford models, the front drainage ports are positioned above the doors near the inner side of the A-pillars, with drainage pipes running down the A-pillars to discharge rainwater near the front wheel arches. The rear drainage ports are located at the bottom of the rear windshield or below the C-pillars, with pipes leading to the rear of the vehicle. If these ports become clogged, water can backflow into the cabin, damaging carpets and electronic components. I've noticed that Ford's design is quite ingenious, but dust tends to accumulate easily. It's recommended to use flexible pipes or a specialized vacuum cleaner for cleaning to prevent long-term water exposure leading to rust. Maintenance should be done gently to avoid damaging the pipe connections. Additionally, checking drainage flow during rainy days can effectively prevent unexpected leaks and related issues.

Was this review help?
6
0
Share
Expand All
McDaisy
11/21/25 4:14am

As a new Ford owner, I remember the sunroof drainage outlets are located around the roof perimeter, especially above the front doors and near the rear windows. The specific positions are on the upper part of the front wheel arches next to the door handles and in the corners of the trunk. These drainage outlets can easily get clogged with mud, leading to water leakage inside the car, which is particularly frustrating during heavy rain when seats and floors get soaked. Regular cleaning is crucial, and I can manage it with a soft cloth or a small stick. Preventing long-term blockages to avoid more significant damage is simple maintenance but extremely important.

Was this review help?
20
2
Share
Expand All
More Forum Discussions

What is the engine model of the Haval H6?

Haval H6 uses a turbocharged engine provided by Shenyang Aerospace Mitsubishi, so this engine is domestically produced. The engine model specifications used in the Haval H6 are: GW4G15B, 1.5T version engine with a maximum power of 124kW and a maximum torque of 285Nm; 2.0T version engine with a maximum power of 169kW and a maximum torque of 385Nm. The Haval H6's engine can be maintained daily using the following methods: Use lubricating oil of appropriate quality grade. For gasoline engines, SD--SF grade gasoline engine oil should be selected based on the additional devices of the intake and exhaust systems and usage conditions; for diesel engines, CB--CD grade diesel engine oil should be selected according to mechanical load, with the selection standard not lower than the manufacturer's specified requirements. Regularly change the oil and filter. The quality of any grade of lubricating oil will change during use. After a certain mileage, performance deteriorates, which can cause various problems for the engine. To avoid failures, oil should be changed regularly according to usage conditions, and the oil level should be kept moderate. When oil passes through the fine holes of the filter, solid particles and viscous substances in the oil accumulate in the filter. If the filter is clogged and oil cannot pass through the filter element, it may rupture the filter element or open the safety valve, allowing oil to bypass through the bypass valve and still carry contaminants back to the lubrication parts, accelerating engine wear and increasing internal pollution. Regularly clean the crankcase. During engine operation, high-pressure unburned gases, acids, moisture, sulfur, and nitrogen oxides from the combustion chamber enter the crankcase through the gap between the piston rings and cylinder walls, mixing with metal powder from part wear to form sludge. A small amount remains suspended in the oil, while a large amount precipitates, clogging filters and oil passages, making engine lubrication difficult and causing wear. Regularly use radiator cleaner to clean the radiator. Removing rust and scale not only ensures the engine operates normally but also extends the overall lifespan of the radiator and engine.
9
3
Share

What is the fuel tank capacity of the Kia KX1?

The fuel tank capacity of the Kia KX1 is 43 liters. It is equipped with a 1.5L naturally aspirated engine or a 1.4T turbocharged engine, paired with a continuously variable transmission (CVT). The vehicle adopts a front-engine, front-wheel-drive layout across all models. Among vehicles in the same class, the Highlander has a fuel tank capacity of 60 liters, while the Haval H6 has a fuel tank capacity of 58 liters. During the actual refueling process, the amount of fuel may exceed the calibrated capacity. This is because the fuel tank capacity specified by the automaker is measured from the bottom of the tank to the safety limit level. There is additional space from the safety limit level to the tank opening, which is designed to allow for fuel expansion when temperatures rise, preventing overflow. If fuel is filled up to the tank opening during refueling, the actual amount of fuel added may exceed the specified tank capacity. If owners want to check the remaining fuel level, they can observe the fuel gauge on the right side of the instrument panel, which is marked with E and F. When the needle is close to E, it indicates low fuel, while nearing F means the fuel level is sufficient.
2
1
Share

Where to Extract Engine Oil from a Land Rover Range Rover?

Engine oil is extracted from the engine compartment of a Land Rover Range Rover. Method for extracting oil from the engine compartment: You can disconnect the metal oil pipe in front of the gasoline nozzle at the point where it connects to the soft hose, insert the soft hose into a fixed container, and then turn the engine key to the drive position. Do not turn it to the start position, as the oil pump will then pump out the gasoline. However, this operation is generally not recommended due to numerous potential hazards. Precautions for oil extraction: Check whether the vehicle's engine is in an overheated state. If it is overheated, do not risk operating, as it can easily cause accidents; Do not operate alone. It is better to have two people cooperating; Ensure the oil collection container is securely fixed, and the oil pipe is inserted into the container properly; Do not extract oil for an extended period or in large quantities. Generally, it should not exceed 10 seconds, otherwise it can easily lead to other malfunctions or accidents.
7
3
Share

What are the reasons for a complete power failure in the FAW J6?

The reasons for a complete power failure in the FAW J6 include low battery voltage and insufficient battery charge. Below are detailed explanations and solutions: Low battery voltage: If the battery voltage is too low to power the dashboard and indicator lights normally, it may have already caused data loss. In this case, you need to visit a 4S store for initialization, commonly known as decoding or code matching. Most domestic vehicles can be jump-started, but many still require initialization at a 4S store. Insufficient battery charge: If the battery is completely dead, you can use jumper cables to connect to another vehicle's battery for a temporary start. However, it is best to remove the battery and take it to a battery shop for charging, as a completely dead battery cannot be fully recharged by short-term driving. It requires a longer charging period to restore its capacity. If you have a portable charger, you can charge the battery directly in the vehicle without removing it. Jump-starting procedure: First, open the hoods of both vehicles. Connect the positive and negative terminals of both batteries using jumper cables. Then, start the engine of the functioning vehicle and press the accelerator pedal without load. Finally, attempt to start the vehicle with the dead battery.
5
1
Share

What is the fuel consumption of the Roewe W5?

Roewe W5, 1.8T automatic fuel consumption is 14.1 liters/100 km. Fuel consumption calculation based on displacement: For a 1.0-liter displacement car, manual transmission models consume a little over 5 liters/100 km; automatic transmission models consume nearly 6 liters/100 km. For a 1.6-liter displacement car, manual transmission models consume over 7 liters/100 km; automatic transmission models consume over 8 liters, nearly 9 liters/100 km. For a 1.8-liter displacement car, manual transmission models consume around 9 liters/100 km, automatic transmission models consume over 10 liters, nearly 11 liters/100 km. For a 2.0-liter displacement car, manual transmission models consume over 10 liters/100 km, automatic transmission models consume around 12 liters, nearly 13 liters/100 km. Fuel consumption introduction: Constant-Speed Fuel Economy: Constant-speed fuel consumption refers to the fuel economy indicator when a car is driving at a constant speed on good road conditions. Since constant-speed driving is a basic operating condition for cars on highways, and this type of fuel consumption is easy to measure, it is widely adopted. For example, France and Germany use the constant-speed fuel consumption at 90 km/h and 120 km/h as the main evaluation indicators for fuel economy.
1
1
Share

What is the reason for the Passat's auto hold not responding?

Passat's auto hold not responding is due to the lever not being fixed, parking brake failure, aging parking brake, excessive gap between the auto hold system's friction plate and brake drum, or severe wear of the parking brake pin shaft. Below are detailed explanations and solutions: Lever not being fixed: The parking brake lever cannot be fixed and needs to be replaced or reinstalled. Parking brake failure: It is necessary to inspect and replace components such as the brake pads. Aging parking brake: The parking brake makes abnormal noises or has aged; lubricant needs to be added or the brake needs to be replaced. Excessive gap between the friction plate and brake drum: Oil contamination or severe wear on the friction plate and brake drum, exposed rivets, or surface hardening causing slippage and malfunction; replace the brake pads and brake disc. How to use the auto hold function: When the driver has fastened the seat belt and the driver's side door is closed, with the engine running, press the auto hold switch to change the auto hold function from off to standby mode. When the brake pedal is pressed to a certain depth and the vehicle has completely stopped, the auto hold function changes from standby to parking mode. When the auto hold is in parking mode, after selecting the appropriate forward or reverse gear, pressing the accelerator pedal will cause the auto hold to release automatically based on the slope gradient.
5
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.