···
Log in / Register

Where is the fog light located on the Honda XR-V?

4 Answers
DelElla
09/05/25 3:33am

Honda XR-V fog lights are located on the front bumper, and the fog light switch is positioned on the light control lever inside the vehicle. The light control lever on either side of the steering wheel features markings for front and rear fog lights, allowing you to turn them on and off. This lever integrates controls for high beams, low beams, high/low beam switching, front/rear fog lights, position lights, and turn signals. The Honda XR-V measures 4328mm in length, 1772mm in width, and 1610mm in height, with a wheelbase of 2610mm and a minimum ground clearance of 130mm. It is paired with a 6-speed manual transmission, featuring a MacPherson strut front suspension and a torsion beam rear suspension.

Was this review help?
11
1
Share
LeTanner
09/17/25 4:12am

As a Honda XR-V owner with over three years of experience, I can share some insights: The fog lights are actually located on the lower sides of the front bumper, roughly near the wheel arch corners. If you crouch down and inspect the front section of the car, you'll spot two small circular lights there. I remember when I first drove in foggy conditions, I fumbled to find the switch—it's usually on the stalk to the left of the steering wheel; just twist it to turn them on. The light beams illuminate the road at a low angle, reducing glare from fog reflection. A safety tip: Don't waste battery by turning them on unnecessarily—use them only when visibility is poor. Their low positioning helps concentrate the light and protects them from flying debris damage. Don't forget to clean that area during car washes, as dust buildup can diminish their effectiveness. In short, they're easy to locate and operate, and making a habit of checking them can enhance driving safety.

Was this review help?
9
1
Share
Expand All
HarperRose
10/31/25 4:41am

When I first got my Honda XR-V, I couldn't figure out where the fog lights were either. Actually, they're embedded in the bottom corners of the front bumper, right next to the wheel arches, in a pretty noticeable position. You can open the hood or simply bend down to look under the front of the car to spot those two small lights. Operating them is straightforward: after starting the vehicle and before turning on the engine, adjust the stalk button near the steering wheel to activate the fog lights, which focus their beam low to help penetrate thick fog. This feature is especially useful in rainy or foggy conditions because regular headlights tend to reflect off the fog, and this design avoids that issue. Their low position also reduces the risk of accidental collisions, and don't forget to check them when clearing leaves. Make it a habit to check if the lights are on during foggy conditions, so you don't leave problems until an emergency arises.

Was this review help?
19
0
Share
Expand All
McCollin
12/14/25 4:49am

Safety first. When driving the Honda XR-V, I pay attention to the fog light position located beside the wheel arches in the lower section of the front bumper. The low mounting point allows the light to project downward, reducing fog reflection and improving visibility. The switch control is conveniently operated via the steering column stalk. I only turn them on during foggy or rainy days to maintain energy efficiency and road etiquette. The position is well-designed to prevent mud buildup that could affect brightness. A quick glance is all it takes to locate them.

Was this review help?
19
4
Share
Expand All
More Forum Discussions

Can I continue driving if the CV joint boot is torn?

It is not advisable to continue driving with a damaged CV joint. When the CV joint boot is torn, the grease inside the CV joint will be thrown out, and dust and dirt can enter the CV joint bearings, causing abnormal wear and even leading to the CV joint seizing up. Here is some relevant information about CV joint boots: 1. Material: The material used is thermoplastic elastomer, also known as thermoplastic rubber, which is a polymer alloy material between rubber and thermoplastic plastics, possessing the dual characteristics of both rubber and plastic. 2. Function: The CV joint boot's role is to contain the grease, preventing it from leaking out and ensuring it stays inside the CV joint. Once the grease inside the CV joint is insufficient, it will cause excessive wear and premature failure of the CV joint. Repairing it requires replacing the CV joint, which is quite expensive. Therefore, if you notice any damage or oil leakage from the CV joint boot, it is essential to replace it promptly.
7
3
Share

What are the three common lubrication methods used in lubrication systems?

The lubrication system generally employs three methods: pressure lubrication, splash lubrication, and periodic lubrication. In automobiles, pressure lubrication is typically used for components that endure significant forces and exhibit high relative motion speeds during operation, such as the crankshaft main bearings, connecting rod bearings, and wheel axle bearings. Pressure Lubrication: This method utilizes an oil pump to deliver lubricating oil under pressure to the friction surfaces of components, forming an oil film of sufficient thickness to withstand mechanical loads and ensure reliable lubrication. It primarily caters to high-speed and heavily loaded engine parts. Splash Lubrication: During engine operation, rotating components like the crankshaft and camshaft splash oil droplets or spray oil from holes in the connecting rods onto friction surfaces. This method lubricates components such as cylinder walls, cams, and piston pins. Periodic Lubrication: This involves the regular application of grease for lubrication. It is mainly used for components like generators, starters, and water pump bearings.
6
4
Share

What is the standard tire size for Santana?

New Santana comes with 14-inch and 15-inch tire sizes. There are two tire models for New Santana: 175/70R14 and 185/60R15. Explanation of tire specification 175/70/R14-85V: 175 indicates the tire width is 175mm; 70 represents the aspect ratio, meaning the section height is 70% of the width; R indicates it's a radial tire; 14 means the rim diameter is 14 inches; 85 is the load index, representing a maximum load capacity of 515 kg (2060 kg for four tires); V indicates the speed rating is 240 km/h. Automotive tire specification parameters are expressed in millimeters for section width and percentage for aspect ratio, followed by tire type code, rim diameter (in inches), load index (permissible load capacity code), and permissible speed code.
20
1
Share

What are the precautions for replacing a damaged or expired driver's license?

Precautions for replacing a damaged or expired driver's license: Before applying for a replacement of an expired driver's license, ensure that there are no pending traffic violations or unresolved accident cases. If the driver's name or date of birth has changed, submit a proof of change issued by the local police station. If required by regulations, also submit the "Inspection Education Record Form" after completing the inspection education. Documents required for driver's license replacement: Identity proof of the motor vehicle driver; the original driver's license; a medical certificate issued by a county-level or military medical institution at the regimental level or above. For applicants applying for a special small automatic transmission passenger vehicle for the disabled, a medical certificate issued by a specialized medical institution designated by the provincial health authority must be submitted. In addition to applying for a replacement at the vehicle management office, you can also apply through the following methods: Replacement via the Traffic Management 12123 App. Download the app, then select Service Center -- Expired License Replacement Service -- fill in the required information. The new license is usually delivered by mail. Visit a police-medical-post service point at a postal office for license replacement. The entire process, from registration to medical examination to the production of the new license, takes only about half an hour. Currently, this service is only available in a few cities, such as Hangzhou.
5
3
Share

How to Turn on the Lights of Volkswagen Lavida?

To turn on the lights of the Volkswagen Lavida: 1. Rotate the light control switch on the left side of the steering wheel one notch forward to turn on the position lights; 2. Rotate the light control switch inward twice to turn on the low beam; 3. Push the light control switch forward to turn on the high beam; 4. Lift the light control switch forward and upward to turn on the right turn signal, and push it downward to the left to turn on the left turn signal. The dimensions of the Volkswagen Lavida are: length 4605 mm, width 1765 mm, height 1460 mm, wheelbase 2610 mm, trunk volume 472 liters, fuel tank capacity 55 liters. It is equipped with a 1.4T turbocharged engine and a 7-speed dual-clutch transmission.
10
3
Share

Are Vehicle Registration and Tax Payment Done Together?

New vehicles require payment of purchase tax before registration; otherwise, registration cannot be completed. To pay the tax for a new vehicle, you need to provide the vehicle certificate of conformity, the owner's ID card, and the vehicle purchase tax invoice. The owner can then take these documents to the nearby vehicle management office to pay the tax. After paying the purchase tax, the owner will receive a purchase tax payment certificate. The vehicle registration process is as follows: The owner needs to prepare the original ID card and a copy, the car purchase invoice, the vehicle certificate of conformity, the purchase tax payment certificate, and the insurance policy, and then go to the vehicle management office for registration and vehicle inspection. The inspection mainly includes checking the vehicle identification code, vehicle appearance, and the vehicle's warning triangle sign. After the vehicle inspection, you can go to the vehicle management office hall to select a license plate number. Generally, there are two options: self-selected numbers or random selection. After selecting the number, pay the fees, and then you can wait to receive the license plate, which usually takes three to five working days.
4
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.