Where is the Focus AUX interface located?

What to do if the ESCL fails to start the car?

ESCL failure should be promptly diagnosed at a 4S shop using a computer to read the fault codes, followed by repair or replacement of the problematic components. Common causes of ESCL failures and their troubleshooting methods: 1. Vehicle pulling to one side: While driving, the steering wheel remains centered, but the car automatically drifts to one side. Causes include uneven tire wear or pressure differences, inconsistent front wheel alignment parameters, bent or deformed steering rods with excessive play, unequal spring force or excessive deformation in the front suspension coil springs, and worn wheel hub bearings with large gaps. 2. Heavy steering: Difficulty in turning the steering wheel left or right. Causes include incorrect front wheel alignment, underinflated tires, deformed or worn steering linkage, tight ball joints, and lack of lubrication in the steering gear.

14

3

Share

What to Do If One Key of a Keyless Start Car Is Lost?

If a key for a keyless start vehicle is lost, you can go to a 4S shop to rematch another key. Then delete the data of the lost key, so that the lost key cannot start the vehicle. First, confirm whether the key was lost unintentionally or due to theft. Extended information: 1. Unintentional loss: Look for a nearby car key specialist to erase the lost key information from the vehicle's system. This will disable the remote and start functions. If only one key is left, it is recommended to make an additional spare key, as the cost of rematching keys after losing all of them is extremely high. 2. Theft loss: It is recommended to replace all mechanical locks of the vehicle and then erase the data of the lost key. Even if the key data is erased, someone with malicious intent can still use the key to open the door and steal items from the car.

16

4

Share

Where is the timing installation point for Jiangling JX493ZLQ3?

There is a small notch at the 12 o'clock position of the crankshaft timing gear, a small protrusion at the position of the 4th cylinder, and a small notch on the camshaft timing tooth surface. There is also a small notch fixed with a screw from top to bottom on the camshaft timing tooth surface, and the same applies to the high-pressure pump timing tooth surface. After seeing the screw hole below, fix it with a screw in the same direction. Below are the specific steps for ignition timing adjustment: 1. Adjusting the distributor contact gap not only affects the spark strength but also the opening and closing timing of the contacts. If the contact gap is adjusted after setting the ignition timing, even a slight change will disrupt the ignition timing. Therefore, the contact gap must be adjusted before setting the ignition timing, within the range of 0.35 to 0.40 mm. 2. Locate the top dead center position of the first cylinder's compression stroke and loosen the first cylinder's spark plug. Slowly rotate the crankshaft until a hissing sound is heard, indicating the first cylinder is in the compression stroke. Open the inspection hole cover on the flywheel housing and slowly rotate the crankshaft to align the timing marks. 3. If there is an octane selector, adjust it to the 0 mark position. 4. Determine the position where the breaker contacts just begin to open. Loosen the distributor housing fixing screw, rotate the housing in the direction of the distributor shaft rotation to close the contacts. Then turn on the ignition switch, rotate the distributor housing in the opposite direction of the distributor shaft rotation while holding the ignition coil high-voltage wire near the ground (about 2-3 mm) until a spark is observed. Finally, tighten the distributor housing fixing screw.

15

1

Share

Why was the Changan Oulve discontinued?

Changan Oulve was discontinued due to safety hazards and low sales caused by its relatively high price. The reasons for its gradual discontinuation include: 1. Safety hazards: Some Changan Oulve vehicles experienced abnormal wear on the torque sensor of the steering shaft assembly after long-term use, causing the controller to enter a fault protection state. In extreme cases, this could lead to reduced power steering assistance and heavier steering, posing safety risks. Starting from March 1, 2017, Changan recalled Oulve vehicles manufactured between November 7, 2012, and November 13, 2015 (inclusive), involving a total of 108,642 units. 2. Low sales: Low sales resulted in low ownership rates, which drove up the cost of parts and repairs, with many parts becoming difficult to obtain. Additionally, the vehicle's front design somewhat imitated a compact SUV, leading to larger blind spots around the A-pillar and relatively high fuel consumption.

17

0

Share

Which Gear to Use When Driving a Manual Transmission Car Through Water?

Depending on the depth of the water, it is generally recommended to drive in 2nd or 3rd gear when navigating through water with a manual transmission. Driving through water advice: If the rain is heavy and the road is deeply flooded, do not attempt to drive through. If the engine stalls while driving through deep water, do not attempt to restart the engine, as this can directly lead to engine failure. Consequences of driving through water: Important electronic components in a car include the ECU, TCU, and various sensors. Without these, the car cannot function properly. The ECU is the brain of the engine, collecting various data and controlling the engine through actuators. Without the ECU, the engine cannot operate normally. If the sensors are damaged, the ECU cannot collect data, and the engine will not function properly. The TCU is the computer for the automatic transmission, collecting data and controlling gear shifts. Without the TCU, the transmission cannot shift gears, rendering the car inoperable. If a car is submerged in water, these sensors and computers can be damaged, and the car will only be usable again after replacing these damaged electronic components.

17

5

Share

What is the warranty period for Volkswagen vehicles?

Volkswagen vehicles have a warranty period of 3 years or 100,000 kilometers. Vehicle warranty conditions: There are many conditions for vehicle warranties, and the warranty periods for different components vary. Consumers should clarify the warranty duration and conditions for consumable parts. Many manufacturers specify in the owner's manual that consumable and wear-and-tear parts are not covered under warranty unless they are quality-related issues. Differences in vehicle warranty periods: Generally, the warranty period for the engine and transmission is the same as the overall vehicle warranty, while consumable parts like batteries, air filters, cabin air filters, and timing belts have much shorter warranty periods. Additionally, the Maintenance Manual typically states that wear-and-tear parts such as wiper blades, brake pads, clutch discs, tires, headlights, and glass are not covered under warranty.

19

2

Share

Where is the Focus AUX interface located?

What to do if the ESCL fails to start the car?

What to Do If One Key of a Keyless Start Car Is Lost?

Where is the timing installation point for Jiangling JX493ZLQ3?

Why was the Changan Oulve discontinued?

Which Gear to Use When Driving a Manual Transmission Car Through Water?

What is the warranty period for Volkswagen vehicles?

Can You Lock the Car with the Windows Open?

Which three keys to press for Audi A6 display screen reboot?

What speed does the letter V on a tire represent?

What is the fuel consumption of the Prado 3.5?