Where is the fan relay located in the Sylphy?

Can Alcohol Be Used to Disinfect a Car?

Alcohol can be used to disinfect a car. Here are the specific details about using alcohol for car disinfection: 1. Use 75% concentration medical alcohol: To achieve effective disinfection and sterilization, car owners need to use medical alcohol with a concentration of 75%. If the alcohol concentration is too low, it will not have the desired disinfecting effect. Alcohol molecules have strong permeability, allowing them to penetrate the bacterial surface membrane, enter the bacteria's interior, coagulate the proteins that form the basis of bacterial life, and thereby kill the bacteria. 2. Turn off the car and be mindful of alcohol usage: Before using alcohol to disinfect the vehicle, car owners should turn off the engine to ensure the car is not running. It is also important to maintain proper ventilation inside the car. Since 75% alcohol has a flash point around 22°C and evaporates quickly, car owners must ensure there are no open flames nearby and be cautious about the amount of alcohol used to avoid high air alcohol concentration, which could lead to an explosion.

18

2

Share

How to Use Reference Points for Parallel Parking and Exiting?

After parking the vehicle steadily in the designated area, shift into reverse gear and begin backing up. At this point, observe the left rearview mirror. When the left boundary line aligns with the lower edge of the left rearview mirror, turn the steering wheel fully to the right. Continue observing the right rearview mirror. When the far-right boundary line becomes visible and the distance between the vehicle body and the corner of the parking space is less than 30cm, turn the steering wheel back halfway. Once you confirm that the right wheels can smoothly enter the parking space, observe the left wheels through the left rearview mirror. When the vehicle body is parallel to the boundary line of the parking space, quickly straighten the steering wheel. Keep observing the left rearview mirror to maintain parallelism between the vehicle body and the boundary line of the parking space. Stop the vehicle when the front boundary line of the parking space appears at the position of the left rearview mirror.

7

0

Share

Are Hybrid Cars Considered New Energy Vehicles?

Hybrid cars are not classified as new energy vehicles. Here is more information about hybrid cars: 1. A hybrid car combines fuel (gasoline or diesel) and electric power, using an electric motor as an auxiliary power source to assist the engine in driving the vehicle. At the start of the journey, the battery is fully charged, providing sufficient energy to meet the vehicle's demands, so the auxiliary power system does not need to operate. When the battery level drops below 60%, the auxiliary power system activates. When the vehicle requires higher energy, both the auxiliary power system and the battery supply energy to the drivetrain. When energy demand is low, the auxiliary power system not only powers the drivetrain but also recharges the battery. 2. Hybrid cars offer superior fuel efficiency and excellent driving performance. Since hybrid cars still rely on fuel for their engines, the assistance of the electric motor during acceleration and startup helps reduce fuel consumption.

9

5

Share

How to Determine if Fake Engine Oil Has Been Added?

When the engine produces abnormal noises, the oil consumption is very rapid, the oil temperature rises, and the oil pressure warning light on the dashboard frequently illuminates, it can be determined that fake engine oil has been added. The following are the specific functions of engine oil: 1. Shock absorption and cushioning: When the pressure at the engine cylinder port rises sharply, suddenly increasing the load on the piston, piston pin, connecting rod, and crankshaft bearings, this load is transmitted and lubricated through the bearings, cushioning the impact load. 2. Rust and corrosion prevention: Lubricating oil adheres to the surface of parts, preventing contact with water, air, acidic substances, and harmful gases. 3. Lubrication and wear reduction: There is rapid relative sliding between the piston and cylinder, as well as between the main shaft and bearing shells. To prevent excessive wear, an oil film of sufficient thickness must be established between the sliding surfaces to separate them, thereby reducing wear.

6

5

Share

What is the function of the car air conditioner ION?

ION refers to the air purification function. When ION is activated, the air purifier starts working. The new ION system mainly consists of two components: a PM2.5 sensor and a negative ion generator. The specific details are as follows: PM2.5 sensor: Its function is to measure the PM2.5 content in the air inside and outside the vehicle, serving as the basis for whether to automatically activate ION and displaying the measured PM2.5 concentration on the car's screen. This sensor is installed inside the vehicle's dashboard, to the right of the blower and on the right front A-pillar. Negative ion generator: It boosts the 12V low voltage to hundreds of volts of high voltage, ionizing the air to form negative ions for air purification, dust removal, deodorization, and sterilization. It is installed between the blower and the evaporator.

8

2

Share

Is Engine Air Leak Serious?

You can still drive with an engine air leak. However, if the intake pipe leaks, it may draw external dust or sand particles into the cylinders, accelerating wear on the cylinder walls or piston rings. Engine air leaks can cause irregular idling and signal abnormalities. Any air leak will lead to unstable engine operation and insufficient power under various conditions. Here are some extended insights: Visual Inspection: The observation method is the simplest and most intuitive way to detect issues. When the engine shows problems, carefully inspect the cylinders and spark plugs for faults. If the spark plug electrodes have excessive carbon buildup and are coated with engine oil, it indicates poor piston ring sealing and oil leakage. Repeated Testing: Infer the source of the issue by testing different scenarios. Check cylinder pressure to understand the cause of the fault based on pressure variations. For example, using a pressure gauge, if the pressure rises significantly, it suggests piston ring wear. If the pressure remains unchanged, it indicates a valve or cylinder gasket leak. Experience Comparison: This method is more suitable for experienced car owners who can roughly identify the cause by comparing throttle responses.

20

4

Share

Where is the fan relay located in the Sylphy?

Can Alcohol Be Used to Disinfect a Car?

How to Use Reference Points for Parallel Parking and Exiting?

Are Hybrid Cars Considered New Energy Vehicles?

How to Determine if Fake Engine Oil Has Been Added?

What is the function of the car air conditioner ION?

Is Engine Air Leak Serious?

How to Remove the Lug Nuts on a Volkswagen?

What does 'lo' mean when displayed on a car's air conditioning?

What Causes the Interior Dome Light to Stop Working?

What is the overtaking sign?