Where is the ETC tag located?

1 Answers
SanTanner
07/29/25 6:06pm
The ETC installation position is generally in the upper middle part of the front windshield horizontally, while for large vehicles such as trucks and buses, it is installed in the lower middle part. The suitable installation position should be no lower than 1.2 meters and no higher than 2.5 meters, with an installation angle between 30 to 90 degrees. For vehicles with factory-installed or aftermarket explosion-proof film, which may affect the signal transmission of the microwave communication link, it should be installed in the microwave sunroof strip. ETC stands for Electronic-Toll-Collection, meaning electronic toll collection system. To apply, the vehicle owner needs to provide original and photocopies of their valid ID card and vehicle license. If the application is handled by a non-owner, the agent's valid ID card is also required. The photocopy of the vehicle license should include the page with the most recent annual inspection stamp. A bank card for deducting highway tolls is needed, and the vehicle must be registered under an individual aged between 18 and 60. For company vehicles, the required documents include: An introduction letter from the vehicle owner (with official seal); photocopy of the organization code certificate or business license (with official seal); original ID card of the agent; original vehicle license; and the vehicle that needs to apply for ETC. Here are some precautions for installing ETC: Do not block the view; it is best to install it behind the rearview mirror: Many car models have a large inclination angle of the windshield, which can reduce the driver's field of vision. If ETC is installed without considering this, it may increase the driver's blind spot. Install it behind the rearview mirror on the right side to avoid blocking the view. Do not affect charging: The ETC electronic tag consumes power but generally does not need to be charged or have its battery replaced because it has a solar panel on the back that can charge itself. Therefore, during installation, avoid the black areas on the windshield and positions that may block the solar panel. Once installed, do not remove it arbitrarily: The button in the middle of the adhesive is an anti-removal lever connected to a switch. After installation, the windshield will press the anti-removal lever in. If the tag is removed arbitrarily, the lever will pop out and trigger the switch, locking the electronic tag and rendering it unusable. You will then need to go to an ETC service point to unlock it. This is designed to prevent multiple vehicles from sharing one device. When using ETC, note that: The ETC transaction sensing area is 8 meters. To prevent the ETC device of the vehicle in front from malfunctioning, maintain a distance of more than 10 meters from the vehicle in front to avoid automatic sensing and paying for the toll of the vehicle in front. The speed limit for ETC lane recognition is 20 kilometers per hour. Driving too fast may result in failure to read the vehicle device information and cause toll deduction failure. When using a debit card bound to ETC, insufficient balance may also lead to toll deduction failure.
Was this review help?
14
4
Share
More Forum Discussions

What are the methods to deal with a car pulling to the right?

The methods to deal with a car pulling to the right are: 1. Check and adjust using a four-wheel alignment instrument; 2. Use a tire pressure gauge to check the tire pressure on both sides and inflate them to the same level; 3. Inspect the tread wear condition on both sides of the tires; 4. Use a four-wheel alignment instrument to check the wheelbase on both sides. If the wheelbase difference is too large, use a body correction instrument to restore the deformation. Reasons for a car pulling to one side while driving: 1. Uneven tire pressure on both sides; 2. Uneven tread wear on both sides of the tires; 3. Poor retraction of the brake caliper piston on one side of the vehicle; 4. Inconsistent preload of the wheel hub bearings on both sides; 5. Uneven wheelbase on both sides of the tires.
1
5
Share

How to Disassemble the Verano Key?

To disassemble the Verano car key, follow these steps: 1. At the small groove of the hook, use a flat-head screwdriver to gently pry the back side. 2. You will notice a gap appearing, then slowly widen this gap. To replace the car key battery, proceed as follows: 1. Remove the key ring, place a 1-yuan coin into a groove on the key, then twist the coin to open it and replace the CR1620 button battery. 2. Identify the positive and negative poles (positive down, negative up) and install the battery correctly. 3. Initialization: After replacing the key, initialize it to restore the remote control function.
3
5
Share

What engine does the Lynk & Co 05 have?

The Lynk & Co 05 is equipped with a 2.0L turbocharged 4-cylinder engine, featuring direct fuel injection technology and an aluminum alloy cylinder head and block. Taking the 2020 Lynk & Co 05 as an example, it belongs to the compact SUV category, with body dimensions of 4592mm in length, 1879mm in width, and 1628mm in height, along with a wheelbase of 2734mm and a curb weight of 1738kg. The 2020 Lynk & Co 05 features a MacPherson strut independent front suspension and a multi-link independent rear suspension. It is powered by a 2.0L turbocharged engine delivering a maximum horsepower of 254ps, a maximum power of 187kW, and a maximum torque of 350Nm, paired with an 8-speed automatic transmission.
8
1
Share

How to Align the Timing Chain on a Roewe 350?

To align the timing chain on a Roewe 350, follow these steps: 1. Locate the small hole blocked by a white plastic plug at the lower right corner of the engine transmission exhaust manifold. 2. Remove the plug and insert an L-shaped iron bar of the same size as the hole. 3. Insert the iron bar into the small hole on the flywheel. 4. Ensure the two round holes on the camshaft are vertically aligned upwards to lock the camshaft in place. Taking the 2015 Roewe 350 as an example, it is a compact car with body dimensions of 4521mm in length, 1788mm in width, 1492mm in height, a wheelbase of 2650mm, a fuel tank capacity of 55 liters, and a curb weight of 1290kg.
20
1
Share

What Type of Transmission Does the Buick Envision Have?

Buick Envision has two types of transmissions: the 1.5T model uses a dry 7-speed dual-clutch transmission, independently developed and produced by SAIC-GM, while the 2.0T model uses a conventional 9-speed automatic transmission. Below is some relevant information: 1. Dry Clutch: A clutch that uses air for cooling is called a dry clutch. In use, the clutch should engage and disengage smoothly and easily, and should not overheat even when operating under semi-engaged conditions for short periods. 2. Dry clutches, because they lack the resistance of oil, generally engage more quickly and with greater force. Also, since there is no oil for cooling, dry clutches are usually exposed to dissipate heat.
16
1
Share

Does the 2017 Lavida come with tire pressure monitoring?

2017 Lavida comes with tire pressure monitoring. The tire pressure monitoring alarm system in the 2017 Lavida is enabled by default and only activates the tire pressure warning light when abnormal tire pressure is detected, alerting the driver. Therefore, there is no physical button for the tire pressure monitoring system in the car. Below is an introduction to the 2017 Lavida's tire pressure monitoring: 1. The Volkswagen Lavida's tire pressure monitoring system uses data transmitted by the ABS system sensors to monitor the rotational speed and rolling circumference changes of each wheel. If the rolling circumference of a wheel changes, the warning light will illuminate. 2. The Lavida's tire pressure monitoring values are not displayed on the dashboard. It is recommended to carry a tire pressure measurement tool to easily monitor the tire pressure of the vehicle's tires.
17
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.