Where is the engine of the Besturn B50 produced?

1 Answers
DiPaislee
07/29/25 4:45pm
The engine of the Besturn B50 is produced in Dalian. The Besturn B50 is equipped with two types of engines: one is a 1.4T turbocharged engine with a maximum power of 100kw and a peak torque of 220Nm, paired with a 6-speed automatic transmission; the other is a 1.6L naturally aspirated engine with a maximum power of 80kw and a peak torque of 155Nm, paired with a 5-speed automatic transmission. Below is an introduction to the turbocharged engine: Principle: The turbocharger is essentially an air compressor that increases intake air volume by compressing air. It utilizes the inertial force of exhaust gases from the engine to drive the turbine in the turbine chamber, which in turn drives the coaxial impeller. The impeller compresses air delivered from the air filter pipe, pressurizing it before it enters the cylinder. Power: As the engine speed increases, the speed of exhaust gas discharge and the turbine speed also increase synchronously. The impeller compresses more air into the cylinder, and the increased pressure and density of the air allow for more fuel to be burned. By correspondingly increasing the fuel quantity and adjusting the engine speed, the output power of the engine can be increased.
Was this review help?
5
2
Share
More Forum Discussions

How to replace the battery of an Audi Q3 car key?

Audi Q3 car key battery replacement method: Press the lock button and pull out the mechanical key first; locate the buckle, which is inside the mechanical key slot; use the mechanical key to pry the buckle from the inside out; remove the loosened cover; ensure the battery's positive pole is facing upward, i.e., positive side up; after replacement, reassemble in reverse order according to the steps. The Audi Q3 is an SUV based on the same PQ35 platform as the Volkswagen Tiguan, with dimensions of 4385 mm in length, 1831 mm in width, and 1608 mm in height. The standard gasoline version is equipped with a 170-horsepower 2.0TFSI engine, while the top model of the Q3 features the 2.0TFSI engine from the Q5 with a maximum power of 211 horsepower.
16
5
Share

How to adjust the time on the Highlander dashboard small display?

Highlander small screen time setting instructions: There are 2 buttons below the clock screen to adjust the time - H for hour and M for minute. There is a DISP button on the right side of the steering wheel. Press and hold it, and instructions for adjusting the time will also appear on the central small screen. Below is some relevant information about the Highlander: 1. In terms of safety features, except for the Elite version, all other models come standard with TPMS tire pressure monitoring and TSS intelligent safety package (including PCS pre-collision system, DRCC dynamic cruise control, LDA lane departure warning, AHB automatic high beam adjustment). The top-end 4WD Supreme version additionally features a PVM panoramic imaging system. 2. In terms of appearance, it has thick chrome decorations, fog lights embedded with chrome elements, and a slightly forward-leaning front design, giving the entire front face a fashionable and three-dimensional look.
3
0
Share

Can the Lynk & Co 01 have its battery replaced outside?

The Lynk & Co 01 can have its battery replaced outside without affecting the car's warranty. The following precautions should be taken when replacing the battery: 1. Avoid contact with metal: Whether removing or installing, be careful not to touch metal when adjusting the positive battery terminal. 2. Pay attention to the battery model and quality: When purchasing a battery, ensure it matches the original car battery model for proper use. It is also recommended to use batteries from well-known brands to ensure quality. 3. Check the battery's manufacturing date: Carefully check the battery's manufacturing date. Generally, batteries produced within the last 3 months are suitable for use, while those older than six months may affect lifespan. 4. Replace without power interruption: Replace the battery without interrupting power to avoid resetting some electronic devices. 5. After replacement: For a new battery, drive for half an hour after installation to allow the battery to charge and ensure sufficient power. Also, test all electronic devices in the car, such as power windows and audio equipment, to ensure they function properly.
4
1
Share

What are the charging steps for the Zotye E200?

The charging steps for the Zotye E200 are: 1. Turn off the vehicle; 2. Connect the charging gun to the fast or slow charging socket of the car; 3. Connect to a 220V AC power source. Below is some related information about the Zotye E200: 1. The Zotye E200 is a 3-door, 2-seater micro hatchback with body dimensions of 2735mm in length, 1600mm in width, and 1630mm in height, with a wheelbase of 1810mm. 2. The Zotye E200 is equipped with an 82-horsepower permanent magnet motor, with a total motor power of 60 kW and a total motor torque of 160 Nm. The rear motor has a maximum torque of 160 Nm, and the drivetrain is rear-wheel drive. The front suspension uses a MacPherson independent suspension, and the rear suspension uses a double-wishbone independent suspension.
12
0
Share

How to Use the One-Button Start in the New Sylphy?

The usage of the one-button start in the New Sylphy: 1. Press the start button to light up the ACC indicator; 2. Press the start button again, and the one-button start button will turn green, initiating the vehicle self-check; 3. After completing the self-check, press the one-button start button while stepping on the brake to start the vehicle. The New Sylphy is a family sedan under Dongfeng Nissan. Based on the concept of comfortable space and technological equipment that the Sylphy has always pursued, it upgrades and improves the four aspects that the current family car market particularly focuses on: appearance, space, power, and fuel consumption. As an economical family car, the New Sylphy also has high requirements for tires, equipped with Dunlop 195/60R16 high-quality tires, fully considering both economy and comfort. The seven-spoke aluminum alloy wheels make it look very dynamic.
1
5
Share

Difference Between Dual Injection and Direct Injection in Automobiles?

The differences between direct injection and dual injection are as follows: 1. Different engine systems. The most critical system of a direct injection engine is the high-pressure fuel injection system, which mainly consists of four parts: the Engine Control Module (ECM), high-pressure fuel rail, high-pressure fuel pump, and fuel injectors. A dual injection engine incorporates both direct injection and port injection systems. 2. Different fuel injection methods. Direct injection directly injects fuel into the cylinder to mix with the air, while dual injection combines the advantages of port injection and direct injection. Under low-load conditions, the port injector sprays fuel during the intake stroke, allowing the air-fuel mixture to enter the cylinder, and then the cylinder injector sprays fuel during the compression stroke to achieve stratified combustion. Under high-load conditions, only direct injection is performed during the compression stroke, improving engine efficiency and avoiding emission issues caused by excess oxygen in low-load conditions with direct injection. 3. Different costs. Due to integrating both direct injection and port injection systems, dual injection engines have two sets of fuel pumps and fuel supply lines, making them significantly more expensive than direct injection engines.
11
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.