Where is the engine number stamped on the Zotye T700?

1 Answers
Cayden
07/30/25 5:22am
The engine stamp of the Zotye T700 is located under the front passenger seat. The engine stamp number of the Zotye T700 cannot be altered. If the engine number or vehicle identification number becomes illegible or damaged due to wear, rust, accidents, or other reasons, you can apply for record filing at the vehicle management office of the registration location. Composition of the Zotye T700 engine stamp number: The digits on the Zotye T700 engine stamp represent the engine number. The engine number consists of four parts: the prefix includes the product series code, generation symbol, and regional/enterprise code; the middle section comprises symbols for the number of cylinders, cylinder arrangement type, stroke, and cylinder diameter; the suffix includes symbols for structural features and usage characteristics; the tail section is a distinguishing symbol. When differentiation is needed within the same product series due to improvements or other reasons, the manufacturer may select appropriate symbols to indicate this, with the suffix and tail section potentially separated by a '-'.
Was this review help?
7
3
Share
More Forum Discussions

Where and How to Complete the Theoretical Hours for Subject 2?

Subject 2's required hours must be completed in the training vehicle. First, after passing Subject 1, the driving school will issue each student a training hour card. Then, when getting in the car for practice, clock in to start recording the training hours, and clock out when getting off to end the hour recording.
1
4
Share

Is the Golf equipped with a wet dual-clutch transmission?

The Golf does not use a wet dual-clutch transmission; it is equipped with a dry dual-clutch transmission. This type of transmission does not have hydraulic resistance, resulting in higher transmission efficiency and better fuel economy compared to wet dual-clutch transmissions. The Golf is a compact car produced by Volkswagen, with dimensions of 4,259 mm in length, 1,799 mm in width, and 1,476 mm in height, and a wheelbase of 2,637 mm. The Golf is powered by two engine options: a 1.2-liter turbocharged engine and a 1.4-liter turbocharged engine. The 1.2-liter turbocharged engine delivers a maximum power of 85 kW and a maximum torque of 200 Nm, with the maximum power achieved at 5,000 to 6,000 rpm and the maximum torque available between 2,000 and 3,500 rpm. It is paired with a 7-speed dual-clutch transmission. The 1.4-liter turbocharged engine produces a maximum power of 150 horsepower and a maximum torque of 250 Nm, with the maximum power achieved at 5,000 to 6,000 rpm and the maximum torque available between 1,750 and 3,000 rpm. It is also matched with a 7-speed dual-clutch transmission.
17
0
Share

Can Rearview Mirror Heating Be Installed Aftermarket?

Rearview mirror heating can be installed aftermarket. It involves installing an electric heating element (heating film) inside the mirror lenses on both sides and addressing the wiring method. It is recommended not to attempt this modification yourself, as it may interfere with the vehicle's original electrical system, causing complications and potential safety hazards. It is best to leave this task to professionals. Below are alternative methods to remove water fog from rearview mirrors: 1. Install rain deflectors: This is a relatively low-cost method. After installing rearview mirror rain deflectors (also known as rain visors or rain covers), they can block rainwater during rain, reducing the need to frequently stop and wipe the mirrors. This method is relatively convenient, though its effectiveness is limited during heavy rain. 2. Apply water-repellent coating: Applying a water-repellent coating to the rearview mirrors can also help maintain clear visibility. Many commercially available glass water-repellent coatings primarily contain silicone oil, which alters the surface tension of water on the glass, preventing water from adhering to the mirror surface. 3. Use soap or dishwashing liquid: Rub a clean, damp cloth vigorously with soap (or dishwashing liquid), then evenly spread the soap residue from the cloth onto the rearview mirror. Wait for three to four minutes until the soap (or dishwashing liquid) on the outer surface of the mirror dries, then wipe it off with a tissue.
19
2
Share

What is the repair method for stripped screw holes in cylinder heads and blocks?

If the screw hole is stripped, you can switch to a larger thread size. For example, if an M4 screw hole is stripped, you can tap an M5 screw hole. If the screw hole is stripped, you can apply glue to the screw before screwing it in. Alternatively, you can abandon the original screw hole and drill a new threaded hole next to it.
17
3
Share

What to Do When the Steering Wheel Keeps Getting Messy During Driving Practice?

This method is suitable for straight-line driving of the vehicle. If the direction deviates to the left, push the steering wheel to the right, then correct it back, and finally straighten the tires. This method is suitable for gentle turns of the vehicle. If turning to the left, pull with the left hand while the right hand follows the slide, then return to the original position.
6
3
Share

How to Handle Traffic Violation Points and Fines Online?

Click on 'City Services' in the convenience life section, then select 'Vehicle Violation Inquiry' on the city services page. Enter the vehicle owner's information, and after querying, you can proceed with the handling. Read the relevant prompts under the 'Traffic Violation Penalty' option and click 'Got it' to proceed.
5
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.