Where is the engine number of Wuling Rongguang?

1 Answers
DelSebastian
07/30/25 7:02am
The engine number of Wuling Rongguang is located on the cylinder block. The letters and numbers stamped on the triangular iron at the connection between the engine and the frame under the co-pilot's seat are the frame number, brand, production date, identification code, and engine number. Engines installed in cars or multi-purpose passenger vehicles are all marked with the professional engine manufacturer, model, and production number in accordance with regulations for the convenience of engine production management and use. In terms of body size, the Wuling Rongguang has a length, width, and height of 4490mm, 1615mm, and 1900mm respectively. In terms of appearance, the Wuling Rongguang offers larger passenger and cargo space than ordinary extended micro buses, with the extended version upgraded from the original 7 seats to 9 seats, providing even more space.
Was this review help?
2
5
Share
More Forum Discussions

At what tire pressure will the alarm be triggered?

During routine checks, observe whether the tire pressure monitor is functioning normally. When the tire pressure drops below 1.8, it will trigger the tire pressure monitoring alarm. Here is more information about automotive tire pressure: 1. A tire pressure alarm is a very dangerous signal that requires high attention because tires are the primary condition for vehicle safety. 2. Tire pressure monitoring operates on the principle of gravity balance. If the tire pressure is balanced, it will display as normal. If a tire is punctured and leaks air, causing the balance of gravity to be disrupted, the monitoring system will trigger an alarm. 3. If the tire pressure monitor does not alert promptly when an issue arises with the vehicle, it indicates a problem with the tire pressure monitor. If the ignition switch is ON/START, and the indicator light and TPMS light both illuminate for 2 seconds before turning off, this situation may occur either because the vehicle's original receiver has not been learned and bound, or because the receiver controller was replaced and has not been learned and bound.
4
0
Share

What is the B Gear?

Automobile B gear is an auxiliary braking gear. The following is a detailed introduction to the B gear of the car: 1. The B gear of the car generally appears in new energy vehicles, such as Toyota's hybrid, Nissan's pure electric, etc. 2. The B gear is usually used when the vehicle is gliding for a long distance or going downhill, especially when going downhill continuously. The B gear assists braking through the drag effect generated by the engine or motor. The purpose is to apply engine braking or strong braking after releasing the accelerator pedal on a steep downward slope, thereby preventing the brakes from overheating. 3. Driving the car with the B gear for a long time has a great impact on the fuel economy of the vehicle. If you are not driving on a downhill section, it is recommended to use the D gear.
7
5
Share

What does the S gear in an automatic car stand for?

The S gear in an automatic transmission stands for Sport mode. When shifted into this gear, the transmission can freely switch between gears. Below are the specific details about the S gear in an automatic transmission: 1. The S gear merely delays the shift timing, maintaining high engine RPM for a period to enhance the car's power without altering other operational aspects. 2. The S gear increases the transmission load in the short term, accompanied by a rise in temperature, which also leads to accelerated wear. Therefore, it is advisable to avoid prolonged use of the S gear. 3. Cars frequently driven in congested urban areas tend to accumulate more carbon deposits in the engine. Thus, periodically using the S gear appropriately helps remove engine carbon deposits, improve fuel economy, and extend engine lifespan.
8
2
Share

How to Conduct Annual Inspection for Vehicles After the Six-Year Exemption Period?

The annual inspection process for vehicles after the six-year exemption period is as follows: 1. The vehicle owner must first ensure there are no traffic violation records for their new vehicle and address any issues promptly. 2. Check the annual inspection date on the vehicle's registration certificate. 3. Bring the original vehicle registration certificate, the owner's original ID card, original compulsory traffic insurance policy, and original vehicle and vessel tax payment receipt to the local traffic police office for processing. 4. The owner should obtain and fill out the exemption application form, then submit the documents and completed form to the staff for review. 5. After approval, present the original registration certificate to the staff to print the new inspection validity date and receive the annual inspection sticker. 6. Take the registration certificate directly to the environmental protection window at the issuing office to obtain the environmental protection label and its copy.
2
1
Share

Are Adaptive High Beam Headlights Good?

Adaptive high beam headlights are practical. Here are the specific details about adaptive high beam headlights: 1. Adaptive high beam headlights, when activated during nighttime driving, use sensors—typically a camera located on the inside of the windshield—to detect oncoming or same-direction vehicles and pedestrians. The system automatically switches between high and low beams, allowing the driver to focus more on driving without the need for frequent manual adjustments. 2. The car's adaptive high beam lighting system employs a camera mounted on the rearview mirror to detect vehicles ahead, with a detection range of up to 400 meters. If an oncoming vehicle is detected, the system selectively dims the high beam's light range to avoid blinding the other driver, ensuring clear visibility for the driver while not affecting the oncoming vehicle. When no vehicles are detected ahead, the system automatically switches back to high beam mode.
19
1
Share

How to Turn Off the Interior Light in a Car?

For models represented by German cars, simply turn the switch clockwise to the desired lighting position. The leftmost part is a rotary switch, where the lighting mode is determined by the position aligned with the horizontal line. From bottom to top, the positions are: off, parking lights, low beam, and auto lights.
1
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.