Where is the engine number of the Highlander located?

1 Answers
VonCamilla
07/30/25 1:49am
The engine number of the Highlander is located at the connection point between the engine and the transmission. The vehicle uses two engine models: 8AR and 2AR. The 8AR refers to an inline four-cylinder engine, while the 2AR refers to a V-type six-cylinder engine. The engine number serves as the engine's identification, as it contains information that the manufacturer labels according to automotive industry regulations. Every vehicle has a corresponding engine number. Taking the 2020 Highlander as an example, it is a mid-size SUV with the following dimensions: length 4890mm, width 1925mm, height 1715mm, a wheelbase of 2790mm, and a fuel tank capacity of 72.5 liters.
Was this review help?
6
0
Share
More Forum Discussions

How to Turn on the Defogging Function in an Audi?

Audi's one-touch defogging function is located in the central control area. Simply activate this function when fogging occurs to conveniently and quickly remove the fog. To quickly eliminate fog, turn on the AC while increasing the set temperature of the air conditioning. The dehumidification function of the AC will help remove the fog efficiently. Using warm air for defogging is slower, and if the interior is already fogged up, turning on the warm air may worsen the fogging. Therefore, it's essential to turn on the warm air before driving. If the fog inside the car is not severe, you can open the windows on both sides. This creates an air convection between the inside and outside of the car, reducing the temperature difference and causing the fog to dissipate.
16
1
Share

How to Deactivate the Vehicle Stability Control System?

Send a brake signal to the vehicle's computer by continuously holding down the electronic parking brake button for 3 seconds. The vehicle's computer will automatically determine that the vehicle requires forced braking. Then issue a command to the ESP (Electronic Stability Program) vehicle stability control system to perform an emergency brake. The vehicle will make judgments and execute commands. By pulling up and pressing down the button, the vehicle will generate a brake signal. The ECU will activate the ESP vehicle stability control system to analyze the vehicle, ensuring that the vehicle does not lose control during emergency braking.
14
0
Share

How to Turn On the Front Fog Lights on the New Levin Luxury Edition?

Locate the light control lever on the left side of the steering wheel of the GAC Toyota Levin vehicle; The light control lever of the GAC Toyota Levin vehicle is marked with corresponding fog light positions; The middle knob on the light control lever of the GAC Toyota Levin vehicle adjusts the fog light switch; Turn the middle knob on the light control lever of the GAC Toyota Levin vehicle to the ON position to turn on the front fog lights; Adjust the wiper control lever of the GAC Toyota Levin vehicle by rotating it to the corresponding position to turn on the fog lights.
3
0
Share

How to Change License Plates for a Vehicle Under Your Name?

Fill out the application form, affix the official seals of both parties' organizations, the vehicle administration seal of the original owner's district or county traffic police branch/detachment, and attach the rubbing film of the vehicle's engine and chassis number. After inspection and archival verification by the vehicle management office, the "Approved for Transaction" seal will be stamped on the application form. Transaction receipts from designated motor vehicle trading markets in the city. The vehicle's driving license and standard photos. For vehicles transferred by court ruling, the "Ruling," "Mediation Agreement," "Judgment," and "Notice of Assistance in Execution" must be provided.
15
5
Share

How to turn off the auto start-stop function on the new Santana?

Open the driver's side door and press the brake pedal to prepare the vehicle for engine start. Press the one-touch start button of the vehicle. At this time, all the lights on the instrument panel will light up. Wait a few seconds for the vehicle self-check to complete, and the vehicle will be in the ready-to-drive state. After the vehicle is started, if the owner needs to turn off the auto start-stop function, they must first locate the auto start-stop button next to the gear shift lever. Press the auto start-stop button of the vehicle, and the auto start-stop system will automatically stop running. At this time, the auto start-stop function has been turned off.
5
1
Share

What to Do When Crossing the Stop Line on a Yellow Light?

Crossing the stop line when the yellow light is on is not considered a violation. Vehicles passing the stop line during the green or yellow light phase are not committing a traffic offense. However, if the countdown to the red light has elapsed, it is considered running a red light. If your vehicle crosses the stop line, you should stop immediately and avoid moving forward or reversing, as this behavior is very dangerous. Reversing in such a situation can easily cause a rear-end collision with the vehicle behind. Check the corresponding rearview mirrors and compare the position of your vehicle body with the line you need to align with. If the vehicle body does not cover the line, adjust accordingly to maintain the desired distance and keep the body parallel to the line.
3
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.