Where is the engine number of the Great Wall Xuanli located?

1 Answers
McNolan
07/28/25 5:18pm
The engine number of the Great Wall Xuanli is located at the rear right side of the engine where it connects to the transmission. It is generally a combination of 7 to 8 digits and letters. In addition to the above method, the engine number can also be checked through the following 4 ways: The vehicle's driving license has the engine number printed on it, usually located on the second last line; The motor vehicle registration certificate will state the engine number; The car purchase invoice will state the engine number; The vehicle purchase tax payment certificate will state the engine number. It should be noted that the engine number is not the same as the engine model. The engine model refers to the specifications and size of the engine within the manufacturer, and engine models can be the same. The engine number refers to the production number of the engine, where each engine can only use one engine number and each engine's number is unique.
Was this review help?
11
1
Share
More Forum Discussions

What does 'Slow down and contact after-sales service' mean?

Slow down and contact after-sales service means that when a machine encounters problems during operation, it should slow down promptly and contact the after-sales service. Precautions during driving are as follows: Note 1: The stronger the high beam at night, the less safe the driving is; the wider the lighting angle, the safer it is; the higher and brighter the lights are raised, the more dangerous it is. Note 2: Habitually stepping on the clutch is not a way to reduce trouble. Note 3: After parking on uneven ground, not only should the handbrake be pulled, but the gear should also be engaged. Note 4: When driving in one direction on a dual-lane road, driving on the dotted line is the most unsafe.
14
2
Share

What Causes the Abnormal Noise When a Truck Fails to Start?

Reasons why a truck fails to start: Insufficient battery voltage or poor connection. Touch the large wire terminal bolts to check if they are hot; if they are, it indicates poor contact. Excessive clearance in the starter armature shaft copper sleeve causes the starter to lose power and may lead to rotor grinding. Excessive wear of the starter brushes results in poor contact with the commutator. Fault in the starter solenoid switch, producing only a clicking sound during startup. Additional Information: There are two types of engine starting difficulties: One is a gradual deterioration in engine starting performance, where the starting time becomes increasingly longer. The other is when the engine starting performance, which has always been good, suddenly deteriorates one day. Chronic deterioration in engine starting performance is mostly due to poor battery performance. In such vehicles, when turning the ignition switch to start the engine, the engine speed initially rises momentarily, then the starter appears underpowered, causing the engine speed to drop extremely low, requiring a long time to start the engine.
10
3
Share

Should I go to a 4S shop or a repair shop for new car scratches?

It all depends on personal choice. The cost of a repair shop is lower than that of a 4S shop, but the repair technology may be slightly worse than that of a 4S shop. The efficiency and accuracy of 4S shops are more advantageous than those of repair shops. However, going to a 4S shop may involve insurance issues, leading to an increase in insurance costs the following year. When the scratches are shallow and the primer is not damaged, you can choose not to repaint at this time, because such scratches are hardly visible unless you look closely, and the primer not being damaged has little effect on the car. Just waxing the scratched area can effectively reduce the severity of the scratches. The scratches are deep, but the scratched area is not a metal part. In this case, the impact is not too great, because for plastic parts, losing a layer of paint is not a big deal, it depends on the owner's personal preference. The scratches are deep, and the scratched area is a metal part. At this time, repainting is necessary, because once the body steel plate and other structures lose the protection of the surface paint, the steel plate is exposed to the air and is prone to corrosion and rust, and the paint surface ages quickly, causing serious damage to the appearance.
14
2
Share

Can You Drive with Only a Driver's License and No Vehicle License?

You cannot drive with only a driver's license and no vehicle license. Below is an introduction to obtaining a vehicle license: Process for obtaining a vehicle license: Currently, replacing a vehicle license no longer requires providing vehicle photos. Only the owner's identity information is needed. After scanning and reading the owner's ID card, staff can complete online verification, review, and other procedures for the owner's identity and vehicle information through the integrated service platform, eliminating the need to drive to the site for verification and photography. Points to note when obtaining a vehicle license: It is important to note that once an online application for replacement or renewal of a vehicle license is submitted successfully, it cannot be canceled. Replacing a lost vehicle license does not require providing the original damaged vehicle license, whereas renewing a vehicle license requires submitting the original damaged license. Mailing is two-way, and the cost is doubled.
6
0
Share

Symptoms of Motorcycle Clutch Wear

Here is a detailed introduction to the symptoms of motorcycle clutch wear: Starter motor freewheeling: If the overrunning clutch is damaged, because the driving force cannot be transmitted to the engine crankshaft, the electric starting system will experience a freewheeling phenomenon. Engine not moving: If the overrunning clutch is damaged and stuck, it will cause the engine to fail to rotate normally, mainly because the overrunning clutch cannot disengage. Here is some additional information: The clutch plate is the medium that transmits engine power to the gearbox. Similar to brake pads, the friction material of clutch plates is mainly made of asbestos-based material, which has certain high-temperature resistance. During vehicle operation, when the clutch pedal is depressed, the clutch plate separates from the engine flywheel. When the pedal is released, the clutch plate engages with the engine flywheel, allowing the engine power to match the driving speed.
4
2
Share

Is it permissible to reverse when there's insufficient space for a U-turn at an intersection?

Reversing is allowed when a U-turn cannot be completed. The U-turn should be initiated at the position of the foremost line. In terms of right-of-way, reversing vehicles have the lowest priority and must yield to any vehicles approaching from behind. Precautions for reversing: Reversing is more challenging than forward driving, primarily due to limited visibility, making it difficult to clearly see the road and obstacles behind. Additionally, during reversing, the rear wheels become the leading wheels, and the front wheels become the trailing wheels, altering the subjective perception and the control points for steering. Consequently, reversing maneuvers may feel less intuitive, convenient, flexible, and precise compared to driving forward. When reversing, always check for oncoming vehicles and pedestrians in front and behind, signal your intention to reverse, and sound the horn to alert other vehicles and pedestrians. Maintain a steady pressure on the accelerator pedal, keeping the speed below 5 km/h, and avoid sudden speed changes to prevent stalling or dangerous situations caused by excessive reversing force. Continuously monitor your progress through the rear windshield and mirrors, and adjust the steering as needed to prevent scraping the front or rear of the vehicle.
19
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.