Where is the engine number of Aoling Jieyun located?

2 Answers
VonIsabelle
07/25/25 10:22am
The engine number of Aoling Jieyun is located on the left side of the cylinder head cover. It is generally a combination of 7 to 8 digits and English letters. In addition to the above method, the engine number can also be viewed through the following 4 ways: The vehicle driving license has the engine number printed on it, usually located on the second last line; The motor vehicle registration certificate will state the engine number; The car purchase invoice will state the engine number; The vehicle purchase tax payment certificate will state the engine number. It should be noted that the engine number is not equal to the engine model. The engine model refers to the specification and size of the engine in the manufacturer, and the engine model can be the same. The engine number refers to the production number of the engine, each engine can only use one engine number and each engine's number is different.
Was this review help?
18
1
Share
LeJude
08/11/25 7:41pm
I usually study vehicle mechanical structures a lot. The engine number of the Aoling Jieyun is generally engraved on the engine block itself, usually on the front or side of the engine cylinder block. You can see it when you open the engine hood. The number is directly printed on the metal, and if not cleaned, it might be covered by oil stains. It's recommended to wear gloves and use a damp cloth to wipe it clean before taking a closer look. This number is particularly crucial during vehicle registration or maintenance—don't confuse it with the chassis number, which is mostly found on the door pillar. If you can't find it, check the vehicle manual or look for diagrams on online forums. I've seen some owners delay repairs because they misreported the number due to not seeing it clearly—this isn't uncommon. Taking the time to locate the correct position is a basic skill.
Was this review help?
20
2
Share
Expand All
More Forum Discussions

Can an A2 Driver's License Drive a Bus?

An A2 driver's license cannot drive a bus. Here is some information about the A2 driver's license: 1. Driver's License: Driving a bus requires an A3 license. The permitted vehicle type for an A2 license is a tractor, with the code A2. The permitted vehicles include heavy and medium-sized full-trailer and semi-trailer motor vehicle trains. The A2 license allows driving all trucks and special-purpose vehicles on the road except tractors. For passenger vehicles, except for large buses and city buses, all other passenger vehicles can be driven. 2. A2: An A2 driver's license can drive city buses with fewer than 19 seats. However, large buses require an A3 license. Therefore, an A2 license cannot drive buses. To drive buses, an upgrade is needed, either to an A3 or A1 license. The upgraded license type would be A2A3 or A1A2.
19
5
Share

What are the symptoms of a broken engine turbocharger?

Here are the symptoms of a broken engine turbocharger: 1. Blue or white smoke from the exhaust pipe, accompanied by a decrease in power. 2. Increased fuel consumption and higher oil consumption. 3. Unstable turbo pressure. 4. Abnormal noises, high water temperature, unstable engine speed, and ineffective turbocharging. Here are methods to determine the condition of the turbocharger: 1. Listen: Normal wear cannot be heard unless foreign objects damage the impeller, affecting dynamic balance and causing slight vibration sounds. Look: Remove the exhaust pipe connected to the compressor side to check for oil presence or excessive blue smoke from the exhaust. 2. Use: The engine feels relatively weak when accelerating (above approximately 1200 rpm). 3. Measure: Use a pressure gauge to measure intake pressure; normal pressure ranges from 0.2 to 0.3 MPa.
17
2
Share

Where is the oil dipstick in an Audi?

Audi does not have an oil dipstick; the oil level is displayed electronically and can be checked in the MMI system. Start the vehicle, locate the 'CAR' button on the center console and press it, then use the central control knob to find the 'Oil Level' option in the MMI menu. Press the central control knob to display the oil level, which may take two to three minutes to appear. Audi is a renowned automobile developer and manufacturer, symbolized by four interlocking rings. It is now a subsidiary of Volkswagen Group, headquartered in Ingolstadt, Germany. Its main models include the A1, A3, A4, A5, A6, A7, A8, Q1, Q2, Q3, Q5, Q7, Q8, TT, R8, as well as the S and RS performance series.
5
3
Share

How many kilometers can a car spare tire run?

Car spare tires can run for 50 kilometers. Here is some introduction about car spare tires: 1. Car: The total mileage of a non-full-size spare tire should not exceed 50 kilometers. Car spare tires are generally divided into full-size spare tires and non-full-size spare tires. Full-size spare tires are the same size as ordinary tires and have no mileage restrictions, but they must be driven at a lower speed. The diameter and width of this type of spare tire are slightly smaller than the four tires, so it can only be used as a temporary replacement, and the driving distance cannot exceed 100km. Therefore, non-full-size spare tires cannot be used for a long time. 2. Full-size spare tire: The size of a full-size spare tire is exactly the same as the four original tires of the car, and it can replace any tire that is temporarily or already unusable. However, the cost is higher, and it takes up more space, and it cannot be used for a long time.
3
0
Share

What Causes Engine Shaking During Cold Start?

Reasons for engine shaking during cold start are as follows: 1. Incorrect Air-Fuel Ratio: Improper air-fuel mixture occurs when the fuel-air mixture is inaccurately proportioned, existing in both open-loop and closed-loop control systems. In vehicles with closed-loop control, the oxygen sensor's operating temperature is 370°C. 2. Carbon Deposits: Carbon buildup on valves and intake passages. If carbon deposits form on engine valves and intake passages, they can absorb a certain amount of fuel, causing the ECU to make incorrect judgments. 3. Cylinder Conditions: Uneven cylinder performance. After prolonged engine use, the clearance between each cylinder liner and piston will vary. Larger clearances in certain cylinders allow high-temperature gases to leak, reducing power output. 4. Faulty Coolant Temperature Sensor: If the coolant temperature sensor malfunctions - for example, when the actual engine temperature is -10°C during cold start but the sensor reports 20°C to the ECU - the computer will inject fuel based on 20°C conditions, resulting in insufficient fuel supply and causing shaking.
17
0
Share

Why is there no response when pressing the accelerator pedal while idling normally?

When a vehicle shows no response to pressing the accelerator pedal and only idles, there can be multiple factors causing this issue. It could be due to a damaged throttle body, a faulty accelerator cable, or poor contact in other sensors such as the air flow meter. If there is no response no matter how you press the accelerator, it is advisable to call for a tow truck or roadside assistance service. It is recommended that the owner visit a repair shop to use a specialized diagnostic tool to read the vehicle's fault codes and diagnose the issue based on these codes. If the issue is not related to the electronic throttle body, it could be problems with the engine's intake, oil, or ignition system. Throttle Body: If the throttle body is damaged, it should be replaced immediately. The throttle body is often referred to as the engine's throat and is installed on the engine's intake pipe. When the driver presses the accelerator pedal, the throttle opening increases, allowing more air to enter the engine. When pressing the accelerator, the cable moves the throttle body, which is essentially the accelerator. The throttle body has a position sensor, and the control unit uses the signal from this sensor to determine the throttle opening. It then calculates the corresponding signal voltage and, based on this signal, determines the vehicle's fuel injection amount. If the throttle position sensor is too dirty or the voltage is unbalanced, the electronic throttle may fail, preventing the accelerator from reaching full speed. Sensor Malfunction: Poor contact in the resistor strip inside the accelerator pedal or potential faults in the electronic throttle sensor motor may occur. These issues require professional diagnosis at a 4S shop or repair facility to identify the cause and carry out the necessary repairs. Engine: For the engine to operate normally, it requires sufficient air intake. If there is a leak or blockage in the intake system, the vehicle's power will drop after filling up with fuel, the speed will not increase, and the body may shake. Faults in ignition components such as the distributor, ignition coil, or high-voltage wires—due to leaks, aging, or poor quality—can cause poor ignition during acceleration, leading to no response.
17
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.