Where is the engine number located on the Changan Honor?

2 Answers
DeAlexander
09/04/25 2:56am
The engine number of the Changan Honor is located on the engine block. Below is a detailed introduction about the Changan Honor: 1. The engine number position is relatively hidden. After turning the left front wheel outward to the maximum, you can reach into the wheel gap and feel the engine number with your hand. It cannot be seen from above the engine compartment. 2. The current Changan Honor has been upgraded from the previous model, featuring a horizontal grille connected to the headlights on both sides, while the front bumper adopts a mesh design. 3. The front face has been redesigned with a horizontal chrome grille, and the front bumper features a mesh design. The high-end models will be equipped with front parking radar. Additionally, the rear light clusters may adopt a wedge-shaped design, and a silver protective plate will be added at the lower part.
Was this review help?
3
1
Share
StChristian
09/16/25 4:08am
I remember when I first drove the Changan Ono, the engine number was located on the engine block under the hood, typically near the top or side close to the radiator. I needed it when helping a friend register the vehicle, and it was quite visible, but if the car was dirty, I had to wipe off the dust to clearly see the engraved numbers. The engine number is crucial, especially for tasks like insurance registration or repairs, and its position might vary slightly across different model years. If you can't find it, try using a flashlight after opening the hood and carefully inspect the area—patience usually pays off. I recommend waiting until the engine cools down to avoid burning your hands. That experience taught me to regularly clean that area, as vehicle safety is something you can't afford to overlook.
Was this review help?
16
4
Share
Expand All
More Forum Discussions

What is the method for replacing the air filter in a Mercedes-Benz GLC260L?

First, prop up the engine hood and locate the position of the air filter. The air filter is located under or inside the glove box on the passenger side. You can open it with a standard Phillips screwdriver, remove the old one, and replace it. The air filter is one-way conductive. When installing, make sure the front side faces upward. Be careful not to install the air filter upside down. Replace it with the new air filter. Close the cover, tighten the screws with the screwdriver, and the air filter replacement is complete.
7
0
Share

How to Use Honda Car Navigation?

On the main interface, there is a "Navigation" option. Click "Agree" to proceed. In the middle-lower part of the screen, there is a "I Want to Go" button. After clicking it, enter your destination. Then confirm, and the navigation will display the map near the destination on the navigation interface. After clicking the "Destination" button in the middle-upper part of the screen, the navigation will automatically start working in 8 seconds.
3
0
Share

Where does the foot brake of a front-wheel drive car brake?

The foot brake of a front-wheel drive vehicle brakes all four wheels, with approximately 60% of the braking force applied to the front wheels. The working principle of the braking system is to generate significant friction, converting the vehicle's kinetic energy into thermal energy. The brake booster and master cylinder are connected in series. The booster is shaped like a large black cylindrical or conical container, functioning as a piston mechanism. A diaphragm divides the booster into two chambers: one connected to the engine intake pipe and the other open to the outside atmosphere. When the engine operates, it creates a vacuum on one side of the booster, generating a substantial pressure difference across the diaphragm. This pressure difference, combined with the force applied by the driver, pushes against the master cylinder to produce powerful braking force.
10
5
Share

How to Whiten Yellowed LED Light Covers Made of Plastic?

The methods to whiten yellowed LED light covers made of plastic are: brushing with a toothbrush dipped in a small amount of cleaner or sanding the cover followed by polishing. The functions of LED lights are: 1. Activating turn signals to alert following vehicles and reduce rear-end collisions; 2. Improving road visibility to enhance driving safety; 3. Informing trailing vehicles of braking to prompt speed reduction; 4. Using hazard lights during temporary stops, emergencies, or poor visibility conditions to notify passing vehicles. The maintenance methods for LED lights include: 1. Regularly inspecting light covers to prevent water droplets; 2. Periodically replacing lights; 3. Properly adjusting light height; 4. Using high-quality bulbs for replacements; 5. Preventing foreign objects from impacting the lights.
8
4
Share

What Causes Vibration When in D Gear and Braking?

If the vibration is slight, it is a normal phenomenon. If the vibration is severe, it may be caused by a damaged engine mount. The following is an introduction to engine mounts: There are engine mount components between the connection points of the engine and the vehicle frame, usually made of rubber, which can buffer certain vibrations from the engine. Without the mounts, the vibrations from the engine during operation would be directly transmitted to the vehicle body, directly affecting ride comfort. Moreover, prolonged use of rubber products can lead to aging, where the mounts harden over time, causing the engine's vibrations to be directly transmitted to the vehicle body.
18
3
Share

What is the fault when the Volkswagen EPC light comes on and how to solve it?

Volkswagen EPC light on fault problems and solutions are as follows: Volkswagen EPC light on fault problems: Intake system failure, such as leakage or blockage; Throttle body dirty, excessive carbon deposits; Substandard fuel selection; Abnormal cylinder pressure, poor working condition; Occasional false alarms; Valve failure, stuck or carbon deposits; ECU failure. Volkswagen EPC light on solutions: Troubleshoot intake system failure, use qualified gasoline, clean throttle body, etc.; Remove carbon deposits from related parts, clean, etc.; Rewrite ECU related data (this is when other faults have been solved but the light still remains); Other faults cannot be ruled out, specific maintenance should be based on actual vehicle inspection results.
8
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.