Where is the engine model located on the Captiva?

Does adding windshield washer fluid to coolant have any impact?

Adding windshield washer fluid to the coolant will lower both the freezing point and boiling point of the coolant. If not cleaned and replaced for a long time, it can affect heat dissipation. Moreover, windshield washer fluid has certain corrosive properties, and in severe cases, it can corrode the cooling system, leading to engine damage, which can have serious consequences. The role of coolant: Coolant is a type of cooling liquid containing special additives, mainly used in liquid-cooled engine cooling systems. It has excellent properties such as preventing freezing in winter, preventing boiling in summer, and offering year-round protection against scale and corrosion. Can different coolants be mixed? It is necessary to use the same brand of coolant. Different brands of coolant may have varying production formulas, and mixing them could lead to chemical reactions between the additives, rendering them ineffective. How to choose coolant: The basic indicators of coolant are the freezing point and boiling point. On the market, coolants come in various specifications such as -15°C, -25°C, -30°C, and -40°C. Generally, it is advisable to choose a coolant with a freezing point at least 10°C lower than the lowest temperature in your region.

2

5

Share

What Causes Fluctuations in Average Fuel Consumption?

Average fuel consumption fluctuates for the following reasons: Vehicle age: Newer cars generally have lower fuel consumption. As a vehicle ages, especially after 5-10 years of use, its fuel consumption gradually increases. Maintenance condition: Carbon buildup in the engine can lead to incomplete combustion. Proper engine maintenance and carbon deposit removal can prevent fuel consumption fluctuations caused by poor or insufficient maintenance. Road conditions: Fuel consumption is also affected by driving conditions. Rough roads or frequent traffic congestion typically result in higher fuel consumption.

13

1

Share

How Often Should Engine Belts Be Replaced?

Automotive engine belts generally need to be replaced every 2 years or approximately 60,000 kilometers. The following conditions also indicate that the generator belt needs replacement: 1. When inspecting the belt, if core fractures or groove cross-section cracks are found, immediate replacement is necessary. 2. If the belt's cover layer separates from the tension cords or the cords become frayed, the belt must be replaced. 3. When the belt is placed on the pulley, there should be a gap between the belt's inner diameter and the bottom of the pulley groove. If no gap is present, the belt must be promptly replaced.

12

2

Share

What Causes Steering Wheel Vibration in a New Car?

New car steering wheel vibration can be caused by the following reasons: Friction between plastic components: Since steering wheels are typically made of plastic parts, they may harden in cold temperatures, potentially causing friction noises. Abnormal sounds from the steering wheel: If the abnormal sound originates from inside the steering wheel, the issue is most likely caused by the steering wheel's clock spring (airbag coil). Aging of tie rod ends: Worn tie rod ends can cause steering wheel vibration and noise. This situation usually requires replacing the tie rod ends followed by a wheel alignment.

15

1

Share

What does pressure loss on the left rear side mean?

A pressure loss warning for the left rear tire indicates abnormal tire pressure in that tire, which requires calibration. Tire pressure standards: According to the international GBT2978-2008 standard requirements: Standard tires: 2.4-2.5bar; Reinforced tires: 2.8-2.9bar; Maximum pressure: should not exceed 3.5bar. Introduction to tire pressure: Tire pressure, strictly speaking, refers to the air pressure inside the tire. In automotive maintenance, the engine is the heart of the car, and its damage will lead to the end of the car's life. Similarly, tire pressure is the blood pressure of the car, and the level of tire pressure plays a crucial role in the performance and power of the vehicle.

12

1

Share

Should the front wheels press on the yellow line during hill-start parking?

The standard is to align the front of the car with the center line. Pressing on the line is not allowed. The front bumper being positioned on the second yellow line is considered passing. Introduction to hill-start parking: Hill-start parking is an assessment point in the driver's license subject two test. It evaluates the driver's ability to operate the vehicle on an uphill slope, correctly park the vehicle at a fixed location near the edge, accurately use the gear, accelerator, and clutch, and then start smoothly. If the vehicle's bumper is not aligned with the pole line during the parking, exceeding 50cm forward or backward, the test will be failed. Precautions: Before ascending the slope, adjust the direction to the correct position in the shortest time possible.

5

Share

Where is the engine model located on the Captiva?

Does adding windshield washer fluid to coolant have any impact?

What Causes Fluctuations in Average Fuel Consumption?

How Often Should Engine Belts Be Replaced?

What Causes Steering Wheel Vibration in a New Car?

What does pressure loss on the left rear side mean?

Should the front wheels press on the yellow line during hill-start parking?

Are There Age Restrictions for Motorcycle Licenses?

How many kilometers can the Avalon run in EV mode?

What is the urban fuel consumption of the Honda Avancier?

Does Full Car Polishing Have a Significant Impact on Car Paint?