Where is the emergency switch for the Hongqi H7 trunk?

Should the Clutch Be Fully Depressed When Shifting Gears?

When shifting gears, it is not always necessary to depress the clutch pedal all the way to the floor. The engagement travel of the clutch and transmission gears varies from car to car—some have longer travel, while others have shorter. As long as the clutch is depressed enough to disengage the transmission gears, you can shift gears. However, the clutch must be depressed every time you shift. Below are some key points about fully depressing the clutch when shifting: 1. Principle: Fully depressing the clutch when shifting completely disengages the engine from the transmission gears, allowing the gear lever to change the gear set before re-engaging. Since the gear sets before and after shifting are different, there is a speed difference between the gear sets to be engaged after shifting, which is synchronized by the synchronizer. 2. Consequences: If the clutch is not fully depressed during the shifting process, there will be a significant speed difference between the shifting gear set and the transmission gear set, making smooth engagement difficult. In mild cases, this can accelerate wear, and in severe cases, it can cause gear grinding, leading to transmission damage.

5

Share

What does SCR mean for trucks?

SCR stands for "Selective Catalytic Reduction" technology, which is a method for treating diesel engine exhaust. The technical approach involves first addressing the particulate emissions of diesel engines through in-engine purification techniques such as optimizing combustion within the cylinder and reducing oil consumption. Then, an SCR aftertreatment device is used to reduce NOx emissions from the engine. SCR System: The SCR system consists of an ammonia supply system, an ammonia/air injection system, a catalytic reaction system, and a control system. To avoid energy consumption from reheating the flue gas, the SCR reactor is typically placed after the economizer and before the air preheater, i.e., in the high-dust section. Ammonia is introduced into the horizontal pipeline before the air preheater and mixed with the flue gas. Catalytic Reaction System: The catalytic reaction system is the core of the SCR process, equipped with NH3 nozzles and a fly ash purge device. The flue gas flows through the duct into the SCR reactor loaded with the catalyst, where NH3 is catalytically reduced to N2 on the surface of the catalyst.

5

0

Share

Can Sedans Be Transported?

Sedans can be transported. Cost of Sedan Transportation: There are certain costs associated with sedan transportation, primarily determined by the origin and destination cities as well as the size of the vehicle. Currently, the transport carriers for sedans have a fixed capacity, typically accommodating 12-14 vehicles. Zhongzhen Logistics: For sedan transportation, you can choose Zhongzhen Logistics. Zhongzhen Logistics Co., Ltd. specializes in the transportation of various types of commercial sedans. Leveraging substantial shipping demand and an extensive collaborative network, they can handle the distribution of single commercial vehicles (including sedans, SUVs, vans, and electric vehicles) or private cars between all major and medium-sized cities nationwide, offering reasonable prices and reliable delivery.

10

4

Share

What is the working principle of ultrasonic sensors?

Principle: Ultrasonic sensors mainly consist of two types of materials: piezoelectric crystals (electrostrictive) and nickel-iron-aluminum alloy (magnetostrictive). Electrostrictive materials include lead zirconate titanate (PZT), etc. The ultrasonic sensor composed of piezoelectric crystals is a reversible sensor that can convert electrical energy into mechanical oscillations to generate ultrasonic waves. At the same time, when it receives ultrasonic waves, it can also convert them into electrical energy. Therefore, it can be divided into a transmitter or a receiver. Below is a related introduction to ultrasonic sensors: 1. Components: Commonly used ultrasonic sensors are composed of piezoelectric wafers, which can both emit and receive ultrasonic waves. Low-power ultrasonic probes are mostly used for detection. They come in many different structures, including straight probes (longitudinal waves), angle probes (transverse waves), surface wave probes (surface waves), Lamb wave probes (Lamb waves), and dual probes (one probe emits, one probe receives), etc. 2. Performance indicators: The core of an ultrasonic probe is a piezoelectric wafer in its plastic or metal housing. The materials that make up the wafer can vary. The size, diameter, and thickness of the wafer also differ, so the performance of each probe varies, and its performance must be understood in advance before use.

15

4

Share

How many points will be deducted for overloading 2 people in a 5-seater car?

A 5-seater sedan overloaded with 2 people, exceeding the passenger limit by 40%, will result in a 6-point deduction and a fine. Article 92 of the "Road Traffic Safety Law of the People's Republic of China" stipulates: Passenger vehicles exceeding the rated passenger capacity on highways shall be fined. "Road Traffic Safety Law": Article 49: Motor vehicles shall not carry more passengers than the approved number, and passenger vehicles shall not carry goods in violation of regulations. Article 92: Passenger vehicles exceeding the rated passenger capacity on highways shall be fined; exceeding the rated passenger capacity by 20% or carrying goods in violation of regulations shall be fined. Freight vehicles exceeding the approved load capacity shall be fined; exceeding the approved load capacity by 30% or carrying passengers in violation of regulations shall be fined.

18

4

Share

How Many Liters of Engine Oil Does the Highlander Need?

Toyota Highlander typically requires approximately 4.5L of engine oil, with the exact amount determined by the oil dipstick markings. If too much oil is added to the Toyota Highlander, it increases the amount of oil splashed onto the cylinder walls by the rotating crankshaft and connecting rods, significantly raising the quantity of oil entering the combustion chamber. Method for measuring engine oil: Turn off the vehicle and park it on level ground; after the engine cools to normal temperature, open the hood, pull out the oil dipstick; wipe the dipstick clean, reinsert it, then pull it out again to check the oil level. Choosing engine oil based on the engine: Select engine oil according to the engine's requirements. It is unnecessary to use overly advanced oil in engines with lower requirements, nor should lower-grade oil be used in engines with higher demands.

7

5

Share

Where is the emergency switch for the Hongqi H7 trunk?

Should the Clutch Be Fully Depressed When Shifting Gears?

What does SCR mean for trucks?

Can Sedans Be Transported?

What is the working principle of ultrasonic sensors?

How many points will be deducted for overloading 2 people in a 5-seater car?

How Many Liters of Engine Oil Does the Highlander Need?

Will Car Stickers Be Penalized?

Why Should You Avoid Flood-Damaged Cars?

Can You Make a U-Turn on a Dashed Yellow Line?

What is the vehicle that mixes concrete called?