···
Log in / Register

Where is the drainage hole of the Lavida door located?

4 Answers
LaAbigail
07/29/25 5:26pm
The drainage holes of the Lavida door are located at the bottom of the door. You can see them by removing the sealing strip at the bottom of the door. Generally, there are two drainage holes on each door. Here is an introduction to the Lavida door drainage holes: 1. When the drainage holes are blocked, water leakage can easily occur at the door, and the dampness inside the car can also damage the window lift and audio wiring harness. 2. Precautions: The sunroof drainage holes of the car are easily blocked by leaves and other debris. If blocked, rainwater can flow into the car through the gaps around the sunroof, lightly wetting the roof trim or, in severe cases, causing water accumulation throughout the cabin. At the same time, rainwater leaking from the sunroof will flow along the A-pillar or C-pillar to the car's floor carpet, which may not be easily noticed by the owner, leading to moldy interiors or even metal corrosion of the car body.
Was this review help?
11
3
Share
McOmar
08/14/25 8:21am
I've been driving my Lavida for several years, and the location of the door drain holes is quite important. They are hidden at the very bottom edge of the door. To be specific, there are two small holes at the bottom of each front and rear door—one near the door lock and the other near the door hinge. When it rains or during car washes, water flows into the door through the window gaps, and these holes help drain it out. Last time, my door had water accumulation because the holes were clogged. I later used a thin wire to clean them out and found a lot of dirt buildup. Now, I regularly check them, especially before the rainy season, by feeling with my fingers to ensure they're clear or rinsing them with clean water to prevent rust. If they frequently get clogged, it's a good idea to check whether driving on slopes or gravel roads is causing too much mud buildup. Keeping them clear helps protect the inside of the door from rust and extends the car's lifespan.
Was this review help?
9
4
Share
Expand All
DiFrank
10/13/25 6:56am
As a new Lavida owner, I was also curious about the location of the door drain holes at first. They are actually located on the narrow edge at the bottom of the doors—both front and rear doors have them. If you look closely, you'll spot several small holes. Once, after washing my car, water accumulated inside the rear door, and the mechanic pointed out that the holes are positioned at the lowest point of the door panel. Now I've learned to clean them by flushing the holes with a soft hose, which helps the water drain easily. These small holes are cleverly designed to prevent water accumulation and rust inside the door. Just be mindful of road conditions and avoid driving into muddy areas to prevent debris from clogging the holes. Regular checks can prevent major issues—don’t underestimate these small holes, as blockages can actually affect the sound of the door opening and closing.
Was this review help?
4
1
Share
Expand All
VonJesse
11/26/25 7:54am
The drainage holes on the Lavida's doors are typically located on the inner side of the door's lower edge, with several small holes at the rear of each front door. I regularly check these areas to prevent water accumulation and potential rust. If the holes get clogged, simply use a thin wire or an air gun to clear them. These holes are well-positioned, and keeping them unobstructed is effective.
Was this review help?
15
0
Share
Expand All
More Forum Discussions

What are the requirements for the third-phase traffic duty station?

The main task is to assist police officers in guiding citizens to comply with traffic regulations. For example, dissuading non-motor vehicles from running red lights, stopping beyond the line, going against traffic, or driving in non-designated lanes; discouraging pedestrians from running red lights or not using sidewalks. Stages: The three-hour persuasion activity is divided into three stages. In the first stage, trainees are required to stand at the intersection for one hour. The second stage allows trainees to rest and learn basic traffic knowledge. In the third stage, trainees continue to stand at the intersection for another hour. They must wear reflective vests uniformly, hold a small yellow triangular flag labeled "Traffic Persuader," and carry a whistle, directing on-site traffic under the command of traffic police. Duty Station: If a trainee leaves the post without approval from a police officer or auxiliary police, fails to dress as required or carry persuasion equipment, performs duties carelessly, or finds someone to substitute for the persuasion activity, they will be deemed as failing. The trainee must redo the duty station until they pass.
13
0
Share

What Causes the Handbrake of a Sedan to Fail to Hold?

Introduction to the reasons why the handbrake fails to hold: 1. Braking effect: The ABS activates, but the car still shows no obvious braking effect, and the braking distance significantly increases. 2. ABS not activated: The wheels do not lock up, the ABS does not activate, and the car rolls forward. The first issue likely stems from the tires, possibly due to severe tire wear, leading to a reduced static friction coefficient, which makes the tires prone to locking up and causes the ABS to intervene too early, failing to generate effective braking force and compromising safety. Solution: 1. Replace the tires: It is recommended to switch to a slightly larger tire size for a significantly improved braking effect. The second issue likely originates from the braking system itself. 2. Replace the brake pads: If a noticeable friction sound is heard during braking, it indicates severely worn brake pads that should be replaced immediately. If no sound is heard, the issue may lie with a malfunctioning brake pump, preventing the brake piston from working effectively. In such cases, it is advisable to promptly visit a repair shop to service the brake assembly.
15
2
Share

Will points be deducted if the two sides of the reverse parking are not equally wide?

As long as the mirrors are not outside the line, no points will be deducted. Here is the relevant introduction about reverse parking: 1. Technique: Align the mirror and turn right fully. When starting the first reverse parking, observe the positional relationship between the left rearview mirror and the parking line. First, turn the steering wheel half a turn to the right and start moving. When the left rearview mirror covers the parking line, turn the steering wheel fully to the right; while reversing with the steering wheel fully turned to the right, look at the right rearview mirror. Observe the distance between the car body and the right front corner of the parking space, keeping this distance at 30 centimeters. If it is too narrow, adjust the steering wheel. The standard width of the parking space line is 15 centimeters, so in the rearview mirror, it should appear as roughly two parking space line widths. 2. Precautions: Generally, start in 1st gear and do not shift incorrectly. When controlling the speed, turning the steering wheel as quickly as possible is always better. When these two conflict, prioritize controlling the speed.
13
5
Share

What Causes the Popping Sound in the Engine Compartment at Idle?

Excessive carbon deposits in the combustion chamber not only increase the compression ratio (resulting in high pressure) but also create high-temperature hot spots on the carbon deposit surfaces, leading to engine knocking. Below is an introduction to car idling: 1. The Role of Car Idling: Idling is a working condition of a car, referring to the engine running in neutral gear. The engine speed during idling is called the idle speed. The idle speed can be adjusted by modifying the throttle size, among other methods. Idling means the engine is "exerting force without doing work." When the engine is running, if the accelerator pedal is completely released, the engine enters the idling state. 2. Causes of Unstable Idling: Direct causes refer to mechanical parts being dirty, worn, or incorrectly installed, leading to variations in cylinder power output, which results in an imbalance of power among cylinders and causes unstable idling. Indirect causes refer to abnormalities in the engine's electronic control system, leading to poor combustion of the air-fuel mixture, making it difficult to balance the power output among cylinders and causing unstable idling.
9
0
Share

Why does the carbon canister solenoid valve keep inhaling at idle?

Carbon canister solenoid valve does not work at idle. If it keeps working now, it is recommended to check whether the solenoid valve control circuit is in the on state and whether the solenoid valve is interfered with, resulting in frequent operation. The following is a related introduction about car idling: 1. The role of car idling: Idling is a working condition of the car, which means that the engine is running in neutral. The speed of the engine at idle is called the idle speed. The idle speed can be adjusted by adjusting the size of the throttle and so on. Idling means the engine "outputs power but does no work". When the engine is running, if the accelerator pedal is completely released, the engine is in an idle state. 2. Reasons for unstable idle speed: Direct reasons refer to mechanical parts being dirty, worn, or installed incorrectly, resulting in changes in cylinder power, which in turn causes an imbalance in the power of each cylinder, leading to unstable engine idle speed; Indirect reasons refer to the abnormal operation of the engine electronic control system, resulting in poor combustion of the mixture, making it difficult to balance the power of each cylinder, causing unstable engine idle speed.
5
0
Share

Scoring Standards for Reverse Parking in the Garage?

Failure to follow the prescribed route or sequence results in an immediate deduction of 100 points, vehicle body crossing the line deducts 100 points, failure to enter the garage deducts 100 points, and stopping midway deducts 100 points. Below is relevant information about reverse parking in the garage: 1. Technique: Align the mirror and turn the wheel fully to the right. When starting the first reverse parking maneuver, observe the position relationship between the left rearview mirror and the parking line. First, turn the wheel half a turn to the right and then start, observing the left rearview mirror blocking the parking line before turning the wheel fully to the right; when reversing with the wheel fully turned to the right, watch the right rearview mirror. Observe the distance between the vehicle body and the right front corner of the garage, maintaining this distance at 30 centimeters. If it's too narrow, adjust the wheel direction. The standard width of the garage line is 15 centimeters, so in the rearview mirror, it should appear roughly as two garage line widths. 2. Precautions: Generally start in 1st gear, ensuring not to shift into the wrong gear. When controlling the speed effectively, turning the steering wheel as quickly as possible is always better. When these two factors conflict, prioritize controlling the speed.
3
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.