Where is the drainage hole of the Geely Emgrand car door located?

2 Answers
VanSienna
09/01/25 5:01am
The drainage hole of the car door is located at the lower part of the door. Below is information about car drainage holes: 1. Fuel tank drainage hole: The fuel tank cap drainage hole can be found by opening the fuel tank filler cap, where you can see the drainage hole underneath the fuel tank cap. The fuel tank cap is not tightly sealed, and it is recessed inward, hence the design of a drainage hole. Since vehicles are used outdoors, wind and sand can accumulate around the fuel tank cap through the gaps. 2. Sunroof drainage hole: Generally, if the sunroof is not opened for a long time, the chance of the four drainage holes at the sunroof getting clogged is low, and even if one is blocked, it is not enough to cause water to flood into the car. Most water ingress is due to water seeping through rubber gaps. Damp interior panels are a sign of a clogged sunroof drainage hole, and a detached sunroof drainage pipe can also cause the interior panels to become damp. A damp interior not only produces unpleasant mildew odors but also breeds bacteria.
Was this review help?
15
0
Share
Miles
09/13/25 7:44am
Last time I washed my car, I noticed that the drainage holes for the Geely Emgrand's doors are mainly located along the bottom edge of the doors, where there are several small gaps or openings designed to prevent water from accumulating inside. Water near the door seals flows here to drain out, avoiding internal rust or mold. If the doors remain closed for extended periods or the car is parked under trees, leaves and debris can easily block these holes, potentially slowing down window operation when water accumulates. I make it a habit to inspect the door gaps monthly with a flashlight and gently clear any debris with a thin wire—simple and hassle-free. Checking after driving in the rain is also a good practice to extend door longevity. Additionally, both front and rear doors have similar structures, positioned roughly toward the lower part. Listening for water sounds while opening and closing doors in a quiet spot can help locate them.
Was this review help?
1
1
Share
Expand All
More Forum Discussions

What is the correct way to brake a motorcycle?

Correct braking methods for motorcycles: 1. At high speeds, the braking force on the front wheel must be greater than that on the rear wheel; 2. At high speeds, the braking force on the front wheel must not cause the front wheel to lock up; 3. When braking uphill, the braking force on the front wheel can be appropriately increased; 4. When braking downhill, the braking force on the rear wheel can be appropriately increased; 5. During emergency braking, the braking force should be slightly less than the force required to lock the wheels; 6. On slippery roads, the rear wheel should brake before the front wheel. It is best to use both front and rear brakes together when braking, as the front brake is primarily designed to assist the rear brake in completing the braking process. Using only the front or rear brake alone will not achieve the shortest braking distance; combining both will yield better braking performance.
9
5
Share

Are Car Key Batteries Universal?

Car key batteries are not universal. Each key's battery has a model number, and currently, there are about 10 types of car key batteries available. When replacing the battery, it is essential to first confirm the battery number and then replace it accordingly. Common battery numbers for car keys include 2032, 2025, 2016, 1632, 1620, and 1616. You only need to purchase the battery with the corresponding number to replace the key's battery. Among these, the CR2016 coin-type battery is commonly used. This type of battery has a voltage of 3V, while car key batteries typically operate on 9V. The battery diameter is 20mm, and the thickness is 1.6mm. When replacing the batteries, it is usually recommended to replace all three batteries at the same time.
8
2
Share

How to Clean Carbon Deposits in the Car Throttle Body?

Methods for cleaning carbon deposits in the car throttle body: When cleaning carbon deposits in the throttle body, first remove the intake hose to expose the throttle body, disconnect the negative terminal of the battery, turn off the ignition switch, straighten the throttle plate, and spray a small amount of carburetor cleaner into the throttle body. Then, carefully wipe the deep parts of the throttle body with a polyester cloth or high-grade non-woven fabric. For areas that are hard to reach by hand, you can use a clip to hold the cloth and clean carefully. The throttle body is a controllable valve that regulates air intake into the engine, available in two types: traditional cable-operated and electronic throttle bodies. After entering the intake pipe, the air mixes with gasoline to form a combustible mixture, which then burns to produce power.
12
1
Share

What Causes Car Vibration at High Speeds?

The reasons for car vibration at high speeds are: 1. Front wheel alignment angle deviation, excessive toe-in; 2. Low tire pressure or tire imbalance caused by repairs or other reasons; 3. Tire deformation or unequal number of tire bolts; 4. Loose installation of transmission system components; 5. Bent drive shaft or deformed front axle; 6. Failed shock absorbers, inconsistent stiffness of front leaf springs leading to frame deformation. Other causes of high-speed steering wheel vibration include inconsistent tire pressure, which can also lead to reduced braking effectiveness, difficulty or heaviness in steering, long-term driving reducing tire lifespan, increased risk of tire blowouts, and higher fuel consumption.
12
1
Share

What kind of engine oil does the LaCrosse use?

The LaCrosse uses engine oil with a viscosity grade of SAE5W30. In extremely cold regions where temperatures drop below -29°C, SAE0W30 oil can be used. This viscosity grade makes cold starts easier for the engine in extremely low temperatures. If the engine oil filler cap has a dexos logo, it is recommended to use engine oil with dexos certification. The LaCrosse is a mid-to-high-end sedan produced and sold by Buick, equipped with General Motors' 1.5T SIDI direct-injection turbocharged engine paired with a 9-speed HYDRAMATIC intelligent transmission for efficient driving. The vehicle dimensions are 5026mm in length, 1866mm in width, and 1459mm in height, with a wheelbase of 2905mm.
6
1
Share

How to reset the tire pressure indicator light on the Octavia?

Method to reset the Octavia's tire pressure indicator light: First, ensure that all four tires have normal pressure. With the tire pressure at the correct level, turn on the ignition and press and hold the tire pressure monitoring switch until you hear an alarm sound, then release to reset the tire pressure indicator light. The Octavia is a vehicle launched by SAIC Volkswagen, with dimensions of 4675mm in length, 1814mm in width, and 1460mm in height, and a wheelbase of 2686mm. In terms of exterior design, this car adopts Škoda's new family design language, showcasing a minimalist style, and the two-tone floating exterior rearview mirrors add a sense of layering to the body. For the suspension, the front uses a MacPherson independent suspension, while the rear employs a torsion beam non-independent suspension.
17
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.