···
Log in / Register

Where is the drainage hole for the Honda CR-V trunk?

4 Answers
GiaMarie
09/01/25 3:00am
The drainage hole for the Honda CR-V trunk is located inside the spare tire compartment in the trunk. The spare tire compartment is at the very bottom of the trunk, and the drainage hole is usually blocked with a rubber plug to prevent rainwater from flowing back into the vehicle. The trunk drainage hole is typically designed with one or two openings. Removing the rubber plug allows water to drain. If there is a leak, it is necessary to identify the cause and address it at the source. Generally, the trunk does not let water in, as rainwater that seeps in is usually drained through the drainage channels near the taillights. The engine drainage hole is usually located at the rear of the engine compartment and can be seen below the front windshield. The door drainage holes are typically at the very bottom of the doors, sealed by weatherstripping. The sunroof drainage holes are hidden around the edges of the sunroof and are connected to the car's A-pillars and C-pillars via tubes, allowing rainwater to flow out along the pillars during rain. The purpose of drainage holes is to provide an outlet for rainwater to exit the vehicle. In fact, cars have many hidden drainage holes, usually located in the engine compartment, sunroof, fuel filler cap, and below the door panels. The functionality of these drainage holes significantly impacts the usability of the car.
Was this review help?
12
0
Share
DePaisley
09/13/25 5:53am
I've been driving a Honda CR-V for over five years and am very familiar with the location of the trunk drain holes. They're positioned in the corners of the trunk floor, near the inner side of the rear bumper or the edges of the spare tire well. Water from car washes or rain drains through these holes to prevent accumulation that could damage the vehicle. Specifically, lifting the trunk mat reveals several small holes. When clogged, water accumulates, potentially causing rust or unpleasant odors, so I recommend using thin wire to clean them annually to maintain proper drainage. The design is logical yet discreet, making maintenance simple but crucial.
Was this review help?
17
2
Share
Expand All
StellaLynn
10/27/25 6:41am
As a car enthusiast, I've studied the Honda CR-V's trunk drain holes. They are typically located at the bottom of the trunk on both sides, near the taillights. Their purpose is to drain rainwater or accidentally spilled liquids, preventing water accumulation that could corrode the vehicle body. Though small, these holes are crucial. For example, in the third-generation CR-V, the holes are positioned more toward the center, while in the fifth-generation, they're closer to the edges. When cleaning, it's best to use a soft brush to gently remove debris—no professional tools are needed. Remembering their location can help you prevent major issues during daily use and extend your beloved car's lifespan.
Was this review help?
18
2
Share
Expand All
VanKathryn
12/10/25 6:56am
I believe understanding the location of drain holes is crucial, as it directly impacts vehicle safety and hygiene. These holes can be found in the corners at the bottom of the CR-V's trunk, cleverly designed yet inconspicuous. Once clogged, water retention can accelerate corrosion or foster mold growth; during maintenance, just spend a few minutes checking if the holes are clear to prevent the issue from worsening and affecting driving comfort.
Was this review help?
19
0
Share
Expand All
More Forum Discussions

What does RDM mean on a car?

RDM on a car stands for random playback of multimedia music. Some car models have RPT next to RDM, which stands for repeat, meaning loop playback. There are many letters on car players, besides RDM and RPT, there are also VOL (volume), SEL (settings), MODE (mode), REW (rewind), FF (fast forward), and MUTE (mute). Common English abbreviations on cars and their meanings: MAP navigation, MENU menu, VOL volume, OK confirmation button, RADIO broadcasting system, MEDIA multimedia system, AC air conditioning system, MODE mode switching, LEFT left turn, RIGHT right turn, LIGHT lights, ABS anti-lock braking system, ESP electronic stability program, SRS airbag, SET cruise control function button, MUTE mute button, which can mute with one click.
18
3
Share

How to Solve the Issue of the Exhaust Monitoring System Warning Light Being On?

The exhaust monitoring system warning light remaining on for an extended period indicates a malfunction in the vehicle's emission system. Solutions include changing the fuel or repairing the emission system. Below is more relevant information: 1. Functions of Vehicle Warning Lights: The vehicle's dashboard features various warning lights. The battery light indicates the working status of the vehicle's battery, while the front and rear fog light indicators show the operational status of the fog lights. The door status indicator displays whether the doors are fully closed. If a door is not completely closed, the light will illuminate to remind the owner to close it properly, and it will turn off once the door is securely shut. When the front and rear fog lights are activated, both lights will illuminate, with the left side indicating the front fog light and the right side the rear fog light. When the turn signal is on, the turn signal indicator will flash at a certain frequency and automatically turn off once the turn signal is deactivated. 2. Reasons for Warning Light Activation: When the vehicle's computer receives parameters from the oxygen sensor indicating that the exhaust emissions significantly exceed national legal standards and the internal program cannot adjust them back within the standard range, the engine control computer will trigger the pollution emission warning light (yellow pollution light) on the dashboard. This alerts the owner to visit a service station to check the cause of the engine pollution emission light.
11
1
Share

What does the inspection validity period until June 2021 mean?

Inspection validity period until June 2021 means that within 90 days of the annual inspection expiration date, you can go to the local vehicle inspection agency for inspection and obtain a new motor vehicle inspection compliance mark. Below is the relevant introduction to vehicle annual inspection: 1. Initial annual inspection: The inspection conducted for motor vehicles to apply for a license plate is called the initial annual inspection. The purpose of the initial annual inspection is to verify whether the motor vehicle meets the conditions for applying for a license plate. 2. Definition: National regulations stipulate that motor vehicles must regularly pass inspections such as exhaust emissions, vehicle appearance, lights, brakes, chassis, etc., and be issued an inspection compliance mark without any traffic violation records. All annual inspection dates are based on the date registered on the vehicle license. Motor vehicles must undergo safety technical inspections according to the following periods from the date of registration, commonly referred to as "annual inspection" or "annual review".
16
4
Share

How to perform a hill start with an automatic transmission?

Method for performing a hill start with an automatic transmission: 1. When stopping on a slope, press the brake pedal to park; 2. Release the brake pedal once the vehicle has started; 3. Then release the handbrake and press the accelerator pedal; 4. This can effectively prevent the vehicle from rolling back due to interrupted braking. The main reason for rolling back during a hill start with an automatic transmission is insufficient engine traction at the beginning. Therefore, pressing the accelerator pedal to increase engine speed during the start can prevent rolling back. The gears of an automatic transmission are: P: Parking gear, after shifting into this gear, the wheels are locked, and the car remains stationary, used when parking; R: Reverse gear, used when reversing; N: Neutral gear, when waiting at traffic lights, shift into neutral and pull up the handbrake to park, avoiding the danger of accidentally pressing the accelerator pedal and causing the car to surge forward; D: Drive gear, shift into D when moving forward, for normal driving conditions, no need to change gears, you can fully trust the car's built-in shifting program; 2: Second gear, uses the engine's speed to slow the car down when going downhill, reducing the load on the brakes; 1: First gear, when fixed in first gear, it can exert strong engine braking force and maintain powerful torque for the car.
2
5
Share

How to Repair a Dented Bumper?

There are several methods to repair a dented bumper: 1. Pour hot water on the dented area. The heat will help pop out the dent. Once the dent returns to its original shape, apply cold water to the heated area to cool it down and allow the rubber to contract and restore. 2. Remove one of the car's screws, reach inside the bumper from behind, and push forcefully to pop out the dent. 3. Use specialized dent repair tools. Bumpers serve multiple purposes, including safety protection, vehicle decoration, and improving aerodynamic performance. From a safety perspective, bumpers absorb impact during low-speed collisions, protecting the front and rear body of the vehicle. In accidents involving pedestrians, bumpers also help protect them. Aesthetically, bumpers are decorative components that enhance the vehicle's exterior appearance.
12
3
Share

How to reset the Suzuki SX4 maintenance light?

Suzuki SX4 maintenance light reset method: 1. Turn on the ignition switch, briefly press the right information display selector handle, and the information display screen will go black and stop; 2. Press and hold the left odometer button for more than 5 seconds until the oil lock display appears on the screen, then release the button; 3. Release the button and press it 5 times consecutively within 2 seconds. The oil lock will turn off, displaying 'SUCCESSFUL', indicating the reset operation is complete. The Suzuki SX4 is a business vehicle under Suzuki, featuring a significantly redesigned front face. The newly designed vertical slat grille connects with the reshaped headlight cluster, creating a very outstanding effect. Combined with the more complex lines of the front bumper, the overall appearance is more fashionable.
1
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.