Where is the disp button matching located on the Highlander?

Where is the rearview mirror heating switch on the new Mazda 3?

The rearview mirror heating switch on the new Mazda 3 is located on the right side below the air conditioning adjustment area. There is a rectangular button with three curved arrows pointing upwards. Simply press it to activate, provided the vehicle is powered on. Rearview mirror heating is particularly useful during rainy or snowy weather. When activated, the heater behind the mirror quickly warms the surface, gradually removing rain or fog, eliminating the need for manual wiping and reducing driving hazards. How to use the rearview mirror heating function: There are generally two ways to activate the rearview mirror heating function. One is combined with the electric rearview mirror adjustment button—just rotate the knob to turn it on. The other is located on the air conditioning control panel—press the heating button to activate it. No manual angle adjustment is needed, as the driver's side has a dedicated adjustment button. Principle of the rearview mirror heating function: After rotating the knob, the electric heater behind the rearview mirror glass rapidly heats up to a fixed temperature (usually between 35-60 degrees Celsius) within minutes. Heat is then emitted from both left and right rearview mirrors. As the temperature rises and evaporation occurs, water droplets on the mirror surface shrink, and fog gradually disappears, effectively clearing frost and condensation. However, in heavy rain, its effectiveness may diminish. Precautions for using the rearview mirror heating function: The heating function works via electric heating wires embedded in the mirror, which consume significant power. Ensure the vehicle is running when using this feature to avoid draining the battery, which could prevent the car from starting. Other methods for defogging rearview mirrors include: Opening windows slightly to allow air circulation, reducing the temperature difference between inside and outside, which helps dissipate fog. Adjusting the car's air conditioning to blow warm air, which can also help clear fog.

14

5

Share

Where is the OBD interface located on the BAIC Huansu H2?

The OBD interface of the BAIC Huansu H2 is located below the left side of the steering wheel. OBD stands for On-Board Diagnostics in Chinese, and this system is primarily used to monitor the operating condition of the engine. During operation, the engine consumes fuel, and the combustion of fuel produces exhaust gases. The On-Board Diagnostics system continuously monitors whether the vehicle's exhaust emissions exceed standards. If the emissions exceed the limit, the OBD warning light will immediately illuminate to alert the driver. The BAIC Huansu H2 is the first MPV independently developed by BAIC Huansu. Its exterior design is quite bold, featuring the Huansu family-style front fascia with a dual chrome grille and the Huansu logo positioned at the center. The headlight clusters are connected to the grille and come equipped with LED daytime running lights. The front bumper has a sporty design, and the lower grille adopts a trapezoidal shape with fog lights on both sides.

7

2

Share

What is the battery model for the Langdong?

The battery model for the Langdong is 55d23l, with a capacity of 60ah. The Hyundai Langdong is a compact sedan with dimensions of 4570mm in length, 1775mm in width, and 1445mm in height, and a wheelbase of 2700mm. The Langdong offers two interior color schemes: all-black and a two-tone dark upper and light lower combination, featuring a simple yet dynamic design with a strong sense of quality inside the cabin. The Langdong is equipped with two engines: a 1.6-liter naturally aspirated engine and a 1.8-liter naturally aspirated engine. The 1.6-liter engine delivers a maximum power of 128 horsepower and a maximum torque of 156 Nm, with peak power achieved at 6300 rpm and peak torque at 4850 rpm. The 1.8-liter engine produces a maximum power of 146 horsepower and a maximum torque of 175 Nm, with peak power at 6500 rpm and peak torque at 4700 rpm.

4

Share

Will the small red light at a crosswalk be captured by traffic cameras?

The small red light at a crosswalk will be captured. Stopping immediately after crossing the line at a red light: If a vehicle has just crossed the stop line when the light turns red but stops immediately, this type of running a red light will not be penalized. However, if there is obvious movement after crossing the line, it will be subject to penalties. The traffic camera captures three photos for running a red light: the vehicle crossing the stop line, followed by two photos of the vehicle moving to the middle of the intersection and reaching the opposite side. Running a red light under traffic police direction: When there is a conflict between the traffic light and the traffic police's hand signals, drivers must obey the on-site instructions of the traffic police. If a driver "runs a red light" due to the traffic police's on-site direction, they can obtain a diversion certificate from the local traffic police station to avoid penalties.

11

0

Share

Is a Tire Pressure of 200 Normal?

A car tire pressure of 200 kPa is not normal at this time. It is best not to continue driving. When driving with insufficient tire pressure, the most obvious effect is an increase in fuel consumption. This is because low tire pressure increases the contact area between the car tire and the ground, resulting in greater friction and increased driving resistance, which in turn leads to higher fuel consumption. Hazards of excessive tire pressure: Reduced tire friction and adhesion, affecting braking performance; Causes steering wheel vibration and deviation, reducing driving comfort; Accelerates localized wear of the central tread pattern, shortening tire lifespan; Increases body vibration, indirectly affecting the lifespan of other components; Overextends the tire cords, reducing tire elasticity and increasing the load on the car while driving; Decreases puncture resistance. When encountering sharp objects like nails or glass on the road, they can easily penetrate the tire, causing internal cracks or blowouts. Methods for addressing insufficient tire pressure: If no damage is visible, simply inflate to the normal tire pressure and reset the tire pressure system; If a puncture is found during inspection, drive to a tire shop promptly for repair and reinflation; If the tire pressure warning reappears after inflation without any punctures, it may be due to air leakage caused by a deformed wheel rim. It is recommended to inspect and replace the wheel rim.

2

Share

Is driving 10-20 kilometers with a tire pressure of 1.9 bar a big issue?

Driving 10-20 kilometers with a tire pressure of 1.9 bar is not a significant issue. However, excessively low tire pressure can cause severe deformation of the tire sidewall, damage the cord layer, and potentially lead to a tire blowout. Hazards of low tire pressure: Increased friction coefficient with the road surface, leading to higher fuel consumption; Causes the steering wheel to feel heavy and may lead to vehicle drift, compromising driving safety; Increases movement in various parts of the tire, causing abnormal heating due to excessive rolling; Reduces the functionality of the cord and rubber, leading to delamination or cord breakage, excessive friction with the rim, causing damage to the bead area and abnormal wear; Doubles the friction between the tire and the ground, rapidly increasing tire temperature, softening the tire, and drastically reducing its strength. High-speed driving under these conditions may result in a tire blowout; Increases tire body deformation, making the tire sidewall prone to cracking, while also causing flexing movements that lead to excessive heat, accelerating rubber aging, cord layer fatigue, and cord breakage. It also increases the tire's contact area with the ground, accelerating shoulder wear. Solutions for insufficient tire pressure: If no damage is visible, simply inflate the tire to the normal pressure and reset the tire pressure system; If a puncture is found during inspection, promptly drive to a tire shop for repair and then reinflate the tire; If the tire pressure warning reappears some time after inflation without any puncture, it may be due to air leakage caused by rim deformation. It is advisable to inspect the rim and consider replacement.

10

3

Share

Where is the disp button matching located on the Highlander?

Where is the rearview mirror heating switch on the new Mazda 3?

Where is the OBD interface located on the BAIC Huansu H2?

What is the battery model for the Langdong?

Will the small red light at a crosswalk be captured by traffic cameras?

Is a Tire Pressure of 200 Normal?

Is driving 10-20 kilometers with a tire pressure of 1.9 bar a big issue?

What are the body dimensions of the BAIC Changhe Q35?

What are the dimensions of the BAIC Huansu H3?

What Causes the Throttle to Suddenly Increase on Its Own in Neutral Gear?

What Are the Types of Snowplows?