···
Log in / Register

Where is the Corolla condenser located?

1 Answers
MacDominic
08/31/25 6:41am
Corolla condenser is located behind the engine. Introduction to condenser: The condenser is a component of the air conditioning system that can quickly transfer heat from the tubes to the air near the tubes. Most are placed in front of the car radiator, which is a device that converts gas or steam into liquid. After being throttled by the throttle valve, it becomes a low-pressure liquid and is sent into the evaporator, where it absorbs heat and evaporates into low-pressure steam to complete refrigeration. Function of condenser: To dissipate heat and cool down the high-temperature and high-pressure gaseous refrigerant discharged from the compressor, condensing it into medium-temperature and high-pressure liquid refrigerant.
Was this review help?
17
3
Share
More Forum Discussions

Is the battery dead if the electric vehicle won't charge?

The electric vehicle not charging may indicate a battery failure. The possible reasons and solutions are as follows: Battery End of Life: The battery has reached the end of its service life. Solution: Replace or repair the battery. Poor Fuse Contact: The fuse inside the battery is broken or there is poor contact between the battery fuse tube and fuse holder. Solution: Replace the fuse. Adjust their positions to ensure good contact, or replace the fuse tube. Low Voltage: The charger has no output voltage or low output voltage, or there is poor contact between the charger and the 220V AC power source. Solution: Replace or repair the charger; reconnect the power source. Abnormal Indicator Light: Abnormal charger indicator light causing false full charge. Solution: Replace or repair the charger.
10
2
Share

Why is the electric car motor not turning and hard to push?

There are several reasons why an electric car motor may not turn and be difficult to push: Controller damage: The controller (three-phase AC inverter) may suddenly break down due to overheating, causing a short circuit between the output three-phase power supply components (at least between two phases). When pushing the vehicle, the motor operates in a short-circuit power generation state (working in energy-consuming braking mode), making it very difficult to push. Solution: Disconnect the controller's wiring to the motor to free the motor from the controller's short circuit, allowing the motor to operate in a no-load power generation state when pushed, making pushing easier. Internal motor short circuit: This may be caused by a sudden inter-turn short circuit inside the motor. In this case, even cutting the wiring at the motor terminals won't help, and pushing resistance will remain very high. The only solution is to tow the vehicle to a repair shop for motor servicing. (This situation is relatively rare)
14
5
Share

What are the requirements for motorcycle registration in Panyu?

The requirements for motorcycle registration in Panyu are as follows: Provide proof of identity: Identity proof of the motor vehicle owner. Purchase certificate: Proof of origin of the motor vehicle such as purchase invoice, motor vehicle whole vehicle factory qualification certificate or import motor vehicle import certificate, vehicle purchase tax payment certificate or tax exemption certificate, motor vehicle traffic accident liability compulsory insurance certificate. Be at least 18 years old: The purchaser must be at least 18 years old and be a Chinese citizen with full civil capacity. Apply for a residence permit: You need to apply for a residence permit, and the applicant can go to the community service center of the current residence to apply.
4
5
Share

Will the Car Display Show Night Mode During the Day?

During the day, the car display will not show night mode; it automatically switches to night mode only in the evening. Below is an introduction to night mode: Definition of Night Mode: The car night vision system uses infrared technology to make darkness appear as bright as daylight, allowing drivers to see farther and more clearly at night. The night vision system consists of two parts: an infrared camera and a light display system on the windshield. Benefits of Night Mode: With this night vision device installed, drivers can see road conditions as clearly as during the day through the light display system. When two vehicles meet, it significantly reduces the adverse visual stimulation caused by the strong headlights of the oncoming car and enhances the driver's ability to discern road conditions in foggy conditions.
16
4
Share

Does changing a white car to laser white require registration?

Changing from pearl white to laser white does not require registration. Because the color difference between pearl white and laser white is not particularly significant, there is no need to go to the vehicle management office for registration. The exterior color of the car indicated on the vehicle license is only a rough designation and does not involve color changes. Similar color ranges: For example, there are many types of red, such as bright red, wine red, French red, etc., which are only labeled as red on the vehicle license. Similarly, white also comes in many varieties, such as taffeta white, pearl white, moon white, beige white, etc., but they are only labeled as white on the vehicle license. Registration is optional: Of course, if the owner is still concerned, they can go ahead and register without any issue. However, if the vehicle's color is changed from another color to white, such as from dark gray to red or from silver gray to sea blue, the color change is too significant, and registration is mandatory. This is no longer just a color change but a shift to a different color category, which requires registration. Otherwise, the vehicle will not pass the annual inspection.
17
3
Share

Do pickup trucks need to go through weighbridges on highways?

Pickup trucks do not need to go through weighbridges on highways. Legal regulations: According to the relevant regulations in January 2020, all trucks must pass through weigh-in-motion channels. Therefore, blue-plate trucks with ETC must go through weigh-in-motion channels when entering the highway. However, this weigh-in-motion channel refers to the entry point. Blue-plate trucks only need to be weighed when entering the highway and can freely choose the exit channel when leaving. Blue-plate truck ETC lanes: When entering the highway, blue-plate trucks need to pass through weigh-in-motion channels. When exiting the highway, they can choose the ETC lane if they have ETC; otherwise, they should use the truck lane.
6
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.