Where is the Corolla battery located?

1 Answers
DaisyMarie
07/29/25 11:19am
The Corolla battery is located in the engine compartment. Open the front hood, and the battery is positioned next to the engine. Typically, an automotive battery has a service life of 2 to 3 years, while the original battery in a new vehicle can last over 3 years. Therefore, if the battery has been in use for approximately two years, it's important to be aware that its lifespan may be nearing its end. The Corolla measures 4630mm in length, 1775mm in width, and 1480mm in height, with a wheelbase of 2700mm. It is equipped with Michelin 215/45R17 tires, TRD Sportivo high-performance shock absorbers, 17-inch TRD TF4 sport rims, reinforced clutch, and high-performance brake pads, ensuring relatively ideal sporty performance.
Was this review help?
19
2
Share
More Forum Discussions

What are the reasons for a car not starting due to fuel supply issues?

There are several reasons why a car may not start: 1. No fuel in the car: If the fuel level is very low or the fuel gauge shows below the red line, the car will naturally not start. 2. Dead battery: A car battery can die due to prolonged parking, reaching the end of its lifespan, generator failure, insufficient or leaking electrolyte, blown fuses, corroded battery terminals, or excessive battery usage. 3. Excessive carbon buildup: Too much carbon buildup can cause poor ignition in the car's spark plugs, leaky valves, and poor fuel injection, leading to misfires, sluggish acceleration, engine shaking, and in severe cases, failure to start. Excessive carbon buildup in the throttle body can block airflow, preventing the engine from starting due to lack of air.
4
4
Share

What Causes a Manual Gear Shift Lever to Become Loose?

Manual gear shift lever becomes loose due to wear of the plastic washer at the linkage joint between the shift lever and the transmission or loosening of the screws. Below are the solutions and precautions: Solutions: Disassemble the shift lever, replace the new plastic washer, and then tighten the screws. If it does not affect daily gear shifting, replacement may not be necessary. Precautions for Manual Gear Shifting: The clutch pedal should be quickly pressed to the bottom. After shifting gears, the clutch pedal should be lifted quickly at the beginning, then slowly when it reaches the semi-engaged state, and then quickly lifted until released. When shifting gears, it is important to master the timing of shifting. The clutch should be pressed all the way down in one motion, and the gear should be engaged in one step. It is also important to familiarize oneself with the gear positions and practice the feel.
11
3
Share

What should not be affected when driving a motor vehicle from the acceleration lane into the traffic lane?

Driving a motor vehicle from the acceleration lane into the traffic lane should not affect the normal driving of other vehicles. When entering the traffic lane from the acceleration lane, pay attention to observe the situation in the traffic lane. When traffic is sparse, merge into the traffic lane from behind normally moving vehicles. If a normally moving vehicle is following closely, control your speed and enter the traffic lane only after all vehicles have passed. Do not abruptly merge into the middle of the lane. Motor vehicles already on the highway should merge into the lane under normal driving conditions. When leaving the highway, motor vehicles should turn on the right turn signal, enter the deceleration lane, reduce speed, and then exit. On the ramp, increase speed to 50 km/h, then enter the acceleration lane, accelerate to 60 km/h, and smoothly merge into the traffic lane. Do not directly accelerate to 60 km/h on the ramp and then enter the traffic lane.
18
4
Share

What does the automotive DMS system mean?

Automotive DMS system refers to the Dealer Management System. The following is a detailed introduction about the automotive DMS system: 1. Overview: In the field of automotive 4S stores: It stands for Dealer-Management-System, mainly used to manage the vast sales network of automotive companies. Automotive 4S stores are car sales stores that integrate car sales, maintenance, parts, and services. 2. Function: The DMS system not only covers vehicle sales, spare parts warehouse, after-sales maintenance services (including workshop management), and customer service for 4S stores, but also successfully builds an interactive information bridge between the manufacturer and dealers, comprehensively meeting the dealers' needs for informatization management of businesses such as 'vehicle sales, maintenance services, parts supply, information feedback, and customer relationships'.
16
3
Share

How to Repair Scratches on Car Chrome Trim?

Methods for repairing scratches on car chrome trim are as follows: 1. Toothpaste Repair Method: Toothpaste contains antioxidants and abrasive particles for stain removal. You can use a damp towel dipped in toothpaste to polish, but it may not be effective against stubborn rust spots. 2. Toilet Cleaner Repair Method: Toilet cleaner also contains dilute hydrochloric acid, which can react chemically with oxides. After dissolving the oxides, wipe them clean with a damp towel. This method is less labor-intensive than using toothpaste and yields good results, basically restoring the brightness of the chrome trim. It is currently a popular method used by many. 3. WD-40 Rust Preventative: WD-40 has strong surface affinity and permeability for metals, penetrating into the metal's pores to 100% eliminate moisture and humidity, forming an ultra-thin, dense protective film to isolate humidity and air, effectively solving the problem of metal rusting 'from the inside out'.
18
0
Share

How Long Can Car Tires Last?

Car tires can last between 3 to 5 years or 50,000 to 100,000 kilometers. Due to varying usage conditions, tire replacement should primarily be based on wear, followed by age. If the wear is severe, the tires need to be replaced even after just one year of use. Conversely, if the wear is not significant but the tires are over 5 years old from their production date, they must still be replaced to avoid the risk of blowouts. Situations where tires cannot be used further include: 1. Presence of tread cracks, tread bulges, missing tread rubber, uneven wear, chemical corrosion, or repeated punctures by foreign objects; 2. Tread wear approaching the wear indicator: Tires must be replaced when the tread depth reaches 1.6 millimeters, as nearly all tires have a marker at this depth; 3. Tread aging with cracks.
7
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.