Where is the cigarette lighter located in the Tiida?

2 Answers
JeffreyLynn
07/29/25 3:17am
The cigarette lighter in the Tiida is located at the lower part of the center console, in front of the gear shift lever. Below is additional information: Tiida models include: 2021 Le Dong Manual Edition, 2021 Ku Dong Edition, 2021 Zhi Xing Edition, 2021 Zhi Zun Edition, 2020 Le Dong Manual Edition, etc. Introduction to the 2021 Le Dong Manual Edition Tiida: The body dimensions are: length 4393mm, width 1766mm, height 1539mm, with a wheelbase of 2700mm, a fuel tank capacity of 50 liters, and a body weight of 1180kg. The 2021 Le Dong Manual Edition Tiida features a MacPherson independent front suspension and a torsion beam non-independent rear suspension. It is equipped with a 1.6L naturally aspirated engine, delivering a maximum horsepower of 122PS, a maximum power of 90kW, a maximum torque of 155Nm, and is paired with a 5-speed manual transmission.
Was this review help?
20
3
Share
ReaganLee
08/12/25 7:09am
As a car owner who frequently performs DIY maintenance, the cigarette lighter socket in my Tiida is located in the lower section of the center console, near the gear shift area, typically featuring a round socket or covered with a cap. For daily use, I most commonly plug in my phone charger there - its prominent position makes it easy to locate. In slightly newer models, it might be designed beside the armrest compartment or inside the glove box, but generally remains within convenient reach of the driver. Remember to clean it regularly to prevent debris blockage affecting functionality, and the manual will provide detailed diagram references for verification. Once located, it ensures safer and more convenient charging while driving.
Was this review help?
16
1
Share
Expand All
More Forum Discussions

What are the vehicle types permitted for an A1 license?

The vehicle types permitted for an A1 license include: large buses with more than 20 passengers, and passenger vehicles with a body length exceeding 6 meters must also use an A1 license. Other vehicle types permitted for an A1 license are: A3 (city buses), B1 (medium-sized buses), B2 (large trucks), C1 (small cars), C2 (small automatic transmission cars), C3 (low-speed cargo trucks), C4 (three-wheeled cars), and M (wheeled self-propelled machinery). According to the appendix of the "Regulations on the Application and Use of Motor Vehicle Driving Licenses," the classification standards for driving licenses are divided into 16 categories: A1, A2, A3, B1, B2, C1, C2, C3, C4, C5, D, E, F, M, N, and P. The Ministry of Public Security issued the "Regulations," further subdividing driving licenses into 15 categories, with new licenses to be replaced during annual inspections or reviews. C1 license: Many people think that a C1 license only allows driving small vehicles with 7 seats or fewer. However, the vehicle types permitted for a C1 license are small vehicles with 9 seats or fewer and a body length not exceeding 6 meters. Vehicles like Jinbei and Ruifeng, as long as they have no more than 9 seats and a body length not exceeding 6 meters, can be driven with a C1 license. Other vehicle types permitted for a C1 license are C2 (small automatic transmission cars), C3 (low-speed cargo trucks), and C4 (three-wheeled cars). C2 license: The C2 license is also one of the more common licenses. It only permits driving automatic transmission cars with 9 seats or fewer and a body length not exceeding 6 meters. It is important to note that a C2 license does not permit driving manual transmission vehicles. B1 license: The vehicle types permitted for a B1 license are medium-sized buses, defined as medium-sized passenger vehicles not exceeding 6 meters in length, with a rated passenger capacity of 10 (inclusive) to 19 (inclusive). Other permitted vehicle types are C1 (small cars), C2 (small automatic transmission cars), C3 (low-speed cargo trucks), C4 (three-wheeled cars), and M (wheeled self-propelled machinery). The B1 license does not include B2 among its permitted vehicle types. B2 license: The vehicle types permitted for a B2 license are heavy, medium-sized cargo trucks or large, heavy, and medium-sized specialized operation vehicles. Heavy and medium-sized cargo trucks are mostly trucks, such as the large dump trucks commonly seen on roads, which fall under the category of heavy trucks. Other permitted vehicle types for a B2 license are C1 (small cars), C2 (small automatic transmission cars), C3 (low-speed cargo trucks), C4 (three-wheeled cars), and M (wheeled self-propelled machinery), which is the same as the B1 license. A2 license: The vehicle types permitted for an A2 license are tractor-trailers. Only drivers with an A2 license can drive tractor-trailers; even drivers with an A1 license cannot. Other vehicle types permitted for an A2 license are B1 (medium-sized buses), B2 (large trucks), C1 (small cars), C2 (small automatic transmission cars), C3 (low-speed cargo trucks), C4 (three-wheeled cars), and M (wheeled self-propelled machinery). A3 license: The A3 license is somewhat special. Its permitted vehicle type is the commonly used city bus. Other permitted vehicle types are only C1 (small cars), C2 (small automatic transmission cars), C3 (low-speed cargo trucks), and C4 (three-wheeled cars). This license does not permit driving B1 or B2 vehicle types. Although city buses and large passenger vehicles look similar, and some city buses may even be longer, an A3 license does not permit driving large passenger vehicles.
19
0
Share

What are the methods for throttle body matching?

Throttle body matching methods generally include manual matching, power-off matching, and diagnostic tool matching. Below are the detailed introductions to throttle body matching methods: Manual matching method: For mechanical cable-type throttle bodies, manual reset is used. By turning the ignition switch on and off several times in succession, the vehicle's onboard computer will delete the original throttle memory and store new throttle data. To verify success, simply start the vehicle and ensure it runs normally. Power-off matching method: After replacing the throttle body, disconnect the negative terminal of the battery for a few minutes, putting the vehicle into a dormant state. During this process, the onboard computer's original memory is restored to factory settings. This method is only suitable for low-end models. Start the vehicle and test-run it normally to confirm success. Diagnostic tool matching method: Use a specialized diagnostic tool to read data, then follow the step-by-step prompts to reset the adaptive values, clear fault codes, and start the vehicle. If the vehicle runs normally, the matching is successful.
13
0
Share

Is Polishing Required Before Crystal Coating for a New Car?

Polishing is not required before crystal coating for a new car. Here are the specific details about automotive crystal coating: Concept: Crystal coating is a hard protective layer specifically designed for key automotive areas such as paintwork, glass, tires and rims, engine, and interior. Its main components include polysiloxane, polysilazane, and inorganic silicon. Function: The crystal coating forms a robust fibrous network on the car's paint surface, filling microscopic invisible pores to achieve a mirror-like effect. It adds a thin diamond-hard shell to the paint surface, increasing the hardness of the paint beyond traditional coating and protecting it from damage.
11
3
Share

Can a used car be transferred to another location?

Used cars can be transferred to another location. The relevant information about the transfer of used cars to another location is as follows: Documents required for the transfer of a used car to another location: The original and one copy of the original owner's ID card / the original and one copy of the agent's ID card; the original and one copy of the registration certificate (big green book); the original and one copy of the vehicle license; the original and one copy of the original purchase invoice (red copy) or the last transfer invoice (red copy); the vehicle purchase tax payment certificate (small red book before 2001, small green book after 2001). One original and three copies of the new owner's ID card / the original and one copy of the agent's ID card; the Motor Vehicle Registration, Transfer, and Cancellation Form / Transfer Application Form; if the new owner is not a local resident and needs to register a local license plate, a valid temporary residence permit is also required. Precautions for the transfer of a used car to another location: The license plate of the used car determines where the transfer and file extraction must be processed first. However, before extracting the file, it is essential to inquire about the used car admission standards of the destination location, as some places also have requirements on the vehicle's age.
10
2
Share

Can the license plate number on the back of a truck be painted by oneself?

The license plate number on the back of a truck cannot be painted by oneself. It must be done at the vehicle management office. The license plate number is a mandatory item for every vehicle to legally drive on the road. Driving without a license plate is considered illegal. The relevant introduction to the license plate number is as follows: The function of the license plate number: The license plate number is the identification plate of the vehicle, and its significance to the vehicle is like the ID number to a person. The license plate is the numbering and information registration of each vehicle. Its main function is to identify the region to which the vehicle belongs and to trace the owner and registration information of the vehicle based on the license plate. Structure of the license plate number: The motor vehicle license plate number consists of the registration authority code and the plate number. For car-type license plates, the number is structured in two rows: the upper row is the registration authority code, and the lower row is the plate number. The registration authority code consists of 2 characters, including a Chinese character and an English letter. The Chinese character is the abbreviation of the province, autonomous region, or municipality directly under the central government, and the English letter is the code of the vehicle management office.
20
1
Share

What does EBP mean on a car?

EBP is a fuel-saving switch. The fuel-saving switch installed in the vehicle can switch between different power modes according to conditions such as heavy load, no load, and climbing, allowing the vehicle to operate under reasonably matched power conditions. The relevant introduction of EBP is as follows: Introduction to EBP: EBP, the full name is "Multi-state Fuel-saving Switch". EBP is mainly used in tractors and trucks. The EBP intelligent fuel-saving system is equivalent to a three-gear selection key for the engine, which can be freely selected according to different road conditions and load weights, keeping the engine operating in the most optimized fuel economy range to achieve fuel-saving purposes. Working principle of EBP: Different gears of the fuel-saving switch correspond to different resistance values. The ECU detects different voltage values, thereby allowing the engine to operate in different states, calibrating the torque and speed ranges corresponding to each state, so that the engine operates within the limited torque and speed ranges according to the selected gear. E gear: used when unloaded; B gear: used when half-loaded; P gear: used when fully loaded.
12
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.