Where is the cigarette lighter in the Roewe RX5 Plus?

What is the High Beam Symbol?

The high beam symbol consists of five parallel horizontal lines from top to bottom and a semicircle facing to the right. When the high beams are turned on, it appears as a blue indicator on the dashboard. Below is a detailed introduction about high beams: Usage scenarios for high beams: When driving at night and there are no lighting tools around the road, making the surroundings very dark, and the road ahead is deep and long, high beams should be used. How to turn high beams on and off: First, turn on the low beams. After the low beams are on, push the control lever downward. The dashboard will then display the high beam indicator, indicating that the high beams are on. To turn off the high beams, simply pull the control lever back to switch to low beams.

19

5

Share

Where is the high beam?

There is a set of light combination switches on the left side of the steering wheel. At night, rotating the combination switch forward one notch turns on the dashboard lights, rotating another notch turns on the low beam, and rotating one more notch activates the high beam. Additional information: 1. When the vehicle speed automatically slows down and the engine sound becomes muffled: It indicates that the driving resistance has increased, and the car is either going uphill or driving on a soft road surface. Conversely, it means the driving resistance has decreased or the car is going downhill. 2. When the lights leave the road surface: Pay attention to possible sharp turns or large potholes ahead, or a vehicle going uphill reaching the top of the slope. 3. When the lights shift from the center of the road to one side: It indicates a curve ahead. When the lights shift from one side of the road to the other, it means the vehicle has entered a series of curves, and the driver should slow down and drive slowly on the right side.

9

5

Share

What is the impact of remotely turning on the air conditioning on the car?

Remotely turning on the air conditioning has no impact on the car. When the air conditioning is turned on while the engine is idling, the engine load increases, but the engine will automatically raise its RPM to ensure normal operation. The only effect is a slight increase in fuel consumption. Reasons why the car air conditioning may not blow air: 1. Blower motor failure: The car blower motor is a crucial component for air conditioning airflow. If the air conditioning compressor fails during use, the air conditioning will definitely not blow air. 2. Clogged air filter: A clogged air filter is a common and significant reason for the air conditioning not blowing air. During operation, the car air conditioning absorbs many impurities from the air. 3. Control system failure: The issue might be with the air vent, air conditioning computer, or control switch. Control system switches generally do not fail, so it is recommended that car owners visit a 4S shop for inspection, as this will simplify the troubleshooting process.

14

0

Share

How many points are deducted for crossing the line?

Driving a short distance over the line results in 2 penalty points, while driving a longer distance over the line that obstructs pedestrians or other vehicles' normal passage incurs 6 penalty points. When the traffic light turns red, if a vehicle crosses the stop line from inside to outside, it definitely constitutes a traffic violation, but there are two scenarios. Reasons for delays in clearing penalty records: 1. System delays in traffic violation query platforms: Violations go through certain procedures from occurrence to being captured, confirmed, and publicized. Similarly, processing penalty points and paying fines also require procedural steps. 2. Use of third-party proxy services: With the rapid development of smartphones, various apps and public accounts for handling violations have emerged. The time taken to process violations varies depending on the channels used by each proxy service to clear violations.

10

5

Share

What is the normal tire pressure for the Volkswagen Tayron?

The normal tire pressure for the Tayron is generally around 2.4-2.5 bar. Due to seasonal factors, the tire pressure can be increased by 0.2 bar in winter and decreased by 0.1 bar in summer. The tire pressure monitoring system in the Volkswagen Tayron can be viewed on the vehicle's dashboard. Simply navigate to the tire pressure monitoring page on the dashboard to check the tire pressure. Tutorial for resetting the Volkswagen Tayron tire pressure light: First, inflate the tires to the normal pressure range; start the vehicle; press the SET button, and the tire pressure warning light will be eliminated. If the tire pressure monitoring indicator light comes on (a yellow symbol, an irregular circle with no stamp on top, four small spikes at the bottom, and an exclamation mark inside), there are generally three possible reasons: Abnormal tire pressure. The system typically alerts when the pressure is below 1.8 bar or above 3.0 bar. In this case, the tires need to be checked and the pressure adjusted. The tire pressure monitoring system has not been reset. After inflating the tires, if the tire pressure reset is not performed promptly, the system will still record the previous data, causing the tire pressure monitoring light to illuminate. Simply perform a tire pressure reset to resolve this. Damaged tire pressure sensor. The tire pressure sensor, which monitors tire pressure, is installed inside the tire and connected to the tire inflation valve. If the sensor is damaged due to impact while driving, the tire pressure warning light will also come on. For sensor damage, the only solution is to replace it with a new component.

1

Share

Is It Normal to Hear Abnormal Noises When Turning the Steering Wheel While Stationary?

The reasons for abnormal noises when turning the steering wheel while stationary may include the sound of friction between the spring steel plate of the horn wire transmission under the steering wheel and the steering wheel itself. It is recommended to apply some lubricating oil at the friction point between the spring steel plate and the steering wheel. The reasons for the steering wheel becoming heavier after wading through water are as follows: 1. When wading through water, it is inevitable for car components to get wet. At this time, it may be due to the drive belt of the hydraulic power steering pump coming into contact with water, causing the belt to slip. As a result, the power steering assistance is reduced, leading to a heavier steering wheel. 2. Water entering the electric power steering components after wading may cause circuit malfunctions. 3. Water entering the steering gear during wading may lead to internal mechanical failures. 4. Moisture in the steering gear wiring harness connector may cause temporary short circuits. 5. Water entering the suspension mechanism rubber bushings increases steering resistance. 6. The power steering fluid mixed with water reduces the functionality of the fluid, increasing steering resistance.

15

2

Share

Where is the cigarette lighter in the Roewe RX5 Plus?

What is the High Beam Symbol?

Where is the high beam?

What is the impact of remotely turning on the air conditioning on the car?

How many points are deducted for crossing the line?

What is the normal tire pressure for the Volkswagen Tayron?

Is It Normal to Hear Abnormal Noises When Turning the Steering Wheel While Stationary?

How to reset tire pressure on Ford Kuga?

Is the Honda UR-V the same as the Avancier?

How to install the rear seat seatbelt in BYD F3?

Can a Car on Monthly Payments Be Sold?