Where is the cigarette lighter fuse of the Arrizo 5 located?

1 Answers
VonJoy
07/29/25 8:21pm
The fuse box of the Arrizo 5 is located under the air vent on the left side of the dashboard. There is a small pull-out box; removing it reveals the fuse box. On the fuse box, there is a diagram indicating the positions of the fuses corresponding to various electrical devices. You can check the position of the cigarette lighter fuse on this diagram and replace it accordingly. Below is additional information: 1. Replacing the fuse: If an unqualified adapter is used or the connected device has excessive power, it often leads to the cigarette lighter fuse blowing. In this case, the fuse needs to be replaced. 2. Precautions: When replacing a fuse, the specifications on the replacement fuse must match those of the faulty fuse. The fuse should only be replaced after the cause of the fault has been identified and resolved. Never use a fuse with a higher ampere rating than specified or any other object, as this may cause severe damage to the electrical system and potentially lead to a fire. In emergency situations, a fuse with a lower safety rating or a fuse from auxiliary equipment can be used as a temporary replacement.
Was this review help?
5
4
Share
More Forum Discussions

At what percentage of battery degradation can a Tesla battery be replaced?

Tesla batteries can be replaced when they degrade to 70% of their original capacity. Tesla battery usage duration: Maximum ten years, minimum three years. The capacity of a Tesla battery is 83Kw per hour, with a density of 200wh per Kg, and a range of 480 kilometers. Tesla batteries can generally be charged and discharged 300 to 500 times. It is best to partially discharge the lithium battery rather than fully discharge it, and to avoid frequent full discharges whenever possible. Once the battery leaves the production line, the clock starts ticking. Whether you use it or not, the lifespan of a lithium battery is only two to three years. Pure electric vehicles: Compared to fuel-powered vehicles, the main differences lie in the four major components: the drive motor, speed controller, power battery, and onboard charger. Compared to gas stations, they are served by public ultra-fast charging stations. The quality differences of pure electric vehicles depend on these four major components, and their value is also determined by the quality of these four components. The applications of pure electric vehicles are also directly related to the selection and configuration of these four major components.
7
4
Share

What are the exterior differences between the high-end and low-end versions of the BMW X1?

The exterior difference between the high-end and low-end versions of the BMW X1 lies in the wheel hub design. The BMW X1 stands out in both exterior design and interior. Exterior Design: The BMW X1 features the classic enlarged double-kidney grille and a larger lower air intake, creating a more imposing visual effect. The 'spoon-shaped' LED daytime running lights are also a signature element. The exposed dual exhaust pipes at the rear enhance the sporty look and feel. Interior: The BMW X1's center console is equipped with a 10.25-inch floating touchscreen, complemented by piano black trim for a stylish touch. The ambient lighting now offers six color options, elevating the interior's premium feel. The X Design package (excluding new energy models) includes a sleek and comfortable M multifunction sports steering wheel.
18
2
Share

Can the Jaguar XJL be modified with ambient lighting at the air vents?

Jaguar XJL can be modified with ambient lighting at the air vents. Ambient lighting features humanization and intelligence. Humanization: Ambient lighting can change its color based on temperature, environment, user activities, and needs. The advanced intelligent control system easily integrates control over different color temperatures, brightness levels, and lighting areas. For example, during daily reading, the bulbs can be adjusted to produce white lighting for better visibility, while at bedtime, the sleep mode can be activated to alter the room's background ambiance, customizable according to different scenarios. Intelligence: The leading intelligent control system effortlessly integrates control over different color temperatures, brightness levels, and lighting areas, turning people's lighting scene demands into reality. Multiple operation methods, including mobile terminals, high-end touchscreen scene switches, and convenient remote controls, allow for customized lighting scenes as desired.
3
3
Share

How often should an idle car be started?

Idle cars should be started at different intervals depending on the season. During summer and spring, an idle car should be started once every 5 to 7 days, while in autumn and winter, it should be started once every 3 to 5 days. Additionally, after each start, the car should run for thirty minutes to ensure the internal components are properly lubricated. Below are some related details: Operations required for idle cars: When parking an idle car, it is necessary to disconnect the negative terminal of the car battery to maintain its charge and avoid startup failure. It is also advisable to cover the car with a car cover to protect the paintwork. Furthermore, you should check the car's engine oil, brake fluid, coolant, and tire pressure to ensure they are at normal levels. Hazards of long-term idling: Gasoline can degrade over time. When seals age, the car may fail to operate properly, and the contact force around the seals can become uneven. In areas with higher force, the seals may deform more. The longer the car remains idle, the harder it becomes to restore these deformations, eventually leading to permanent deformation and potential oil leaks. The battery may also fail prematurely. Most cars use lead-acid batteries, which automatically discharge when the car is not in use. Under normal conditions, the battery's capacity can decrease by more than 1% per day due to self-discharge. In severe cases, long-term self-discharge can lead to sulfide formation on the electrode plates, affecting the battery's rechargeability and ultimately causing early failure. Electronic components may also malfunction. Automotive electronic components and connectors are designed to be waterproof, moisture-proof, and corrosion-resistant. If these protections fail, malfunctions can occur. For parked cars, the risk of moisture damage to electronic components or connectors increases significantly, and the longer the car remains idle, the higher the probability of failure.
5
2
Share

What is the bulb model for the headlights of the Bora Classic?

The original bulb is an Osram bulb, with both high and low beams using H7. Pay attention when replacing the bulb. Dealing with light decay: As the headlights are used, the brightness of the bulb will gradually decrease. This normal physical phenomenon is called light decay. Dim headlights can easily cause accidents, so they should be replaced promptly once they become dim—don't wait until they fail. Choosing high-quality bulbs can delay color decay, extend service life, and provide more safety for your driving. Regularly check your headlights, and it is recommended to replace the bulbs in pairs every 20,000 kilometers. Five minutes after the engine is turned off: Wait at least five minutes after turning off the engine before replacing the bulb. Before replacing the car bulb, you will need gloves and protective goggles. Use alcohol to wipe off fingerprints or grease on the outer surface of the lamp housing, and avoid touching the glass surface of the bulb with bare hands to prevent fingerprints from contaminating the glass shell and shortening the bulb's lifespan. After replacing the bulb, adjust the headlights to avoid glare.
7
5
Share

What are the symptoms of a faulty BMW eccentric shaft sensor?

BMW eccentric shaft sensor failure can cause the car to fail to start. The criteria for judging bearing damage mainly depend on two manifestations: vibration and temperature. Vibration of eccentric bearings: Bearing vibration is highly sensitive to bearing damage, such as spalling, indentations, rust, cracks, and wear, all of which can be reflected in bearing vibration measurements. Therefore, by using special bearing vibration measuring devices (such as frequency analyzers), the magnitude of vibration can be measured, and the specific abnormality can be inferred from the frequency distribution. The measured values vary depending on the bearing's operating conditions or the sensor installation position, so it is necessary to analyze and compare the measurement values of each machine in advance to determine the judgment criteria. Temperature of eccentric bearings: The temperature of eccentric bearings can generally be inferred from the temperature outside the bearing housing. If the outer ring temperature can be directly measured using an oil hole, it is even more suitable. Typically, the temperature of eccentric bearings gradually rises as the bearing begins to operate and stabilizes after 1-2 hours. The normal temperature of the bearing varies depending on the machine's heat capacity, heat dissipation, speed, and load. If lubrication or installation is improper, the bearing temperature will rise sharply, leading to abnormally high temperatures. In such cases, operation must be stopped, and necessary preventive measures must be taken. Using thermal sensors, the working temperature of the bearing can be monitored at all times, and automatic alarms or shutdowns can be implemented when the temperature exceeds the specified value to prevent bearing seizure accidents.
18
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.