Where is the cigarette lighter fuse located in the Ford Kuga?

2 Answers
VanAndrew
07/28/25 9:40pm
In the Changan Ford Kuga, the cigarette lighter fuse is located in the fuse box in the engine compartment. The fused power outlet plug is inserted into the top circular slot. Typically, the inside of the removed cover panel lists the component names and corresponding numbers, allowing technicians to locate the components based on the information. The method and steps for finding the fuse are as follows: 1. Before searching for the fuse, ensure safety by turning off the engine and power supply. 2. Locate the corresponding position and use a small pry tool to lift the protective cover. 3. Remove the fuse box, and the cigarette lighter's position can be seen on the inner side, located as the second fuse in the first column. 4. Use a test light to preliminarily diagnose the fuse. If one end lights up during testing while the other does not, it indicates the fuse is blown. 5. Use a specialized tool to remove the faulty fuse and replace it with a new one.
Was this review help?
5
1
Share
MatteoLynn
08/12/25 2:16am
The cigarette lighter in my Escape suddenly lost power, and it took me a while to locate the issue. There's a small box under the lower left corner of the steering wheel—you'll need to crouch down to see it. Specifically, it's the 15-amp blue mini fuse labeled F61 on the back of the box cover. Use tweezers to pull it out and check if the middle section is broken. If it's blown, replace it with one of the same rating. A word of caution: never use a coin or wire as a substitute—my neighbor did that and ended up burning the wiring harness black. For a temporary charging solution, the rear seat 12V outlet has an independent fuse and can serve as an emergency workaround. Always turn off the main power switch before replacing the fuse—safety first.
Was this review help?
7
4
Share
Expand All
More Forum Discussions

How to Replace the Air Filter in a 2020 Magotan?

Open the engine hood and locate the position of the air filter. Lift the retaining clip on the air filter cover, remove the air filter (there are clips and screws), and check for excessive dust. Install the new filter in its original position, paying attention to the installation direction. Secure the air filter cover and fasten the retaining clip. Open the glove box, pinch both sides inward to squeeze it, then remove it. Take out the cabin air filter and check for contamination.
17
3
Share

How to Handle a Car After Insurance Assessment Declares It a Total Loss?

After a vehicle is declared a total loss, the unit or individual must submit a scrapping application. The unit or individual should bring the vehicle's driving license or a copy of it, along with the ID card of the person delivering the car, to the Municipal Metal Recycling Corporation to obtain a vehicle scrapping and recycling certificate. With the vehicle scrapping and recycling certificate, driving license, license plates, and other relevant documents, proceed to the Municipal Vehicle Management Office to complete the household registration cancellation. Using the vehicle scrapping and recycling certificate, go to the Transportation Bureau and Operation Department to complete the procedures for canceling road maintenance fees, freight charges, and fixed asset registration.
19
5
Share

How to Close Windows with Remote Control on Baojun 730?

Press the button upward to the first gear, and release it when reaching the desired position. Some models do not have the one-touch window lift function enabled by default, so it should be manually activated. Pulling the button forcefully will reach the second gear, at which point the window will completely close. Automatic unlocking function. When the gear is shifted to P and the engine is turned off, the vehicle will automatically unlock. The key can also be used for one-touch window control. Press and hold the lock button for 3 seconds without releasing, and all four windows will automatically rise.
17
5
Share

How to Set the Seat Memory in BMW X5?

After starting the ignition, ensure the car is in an operational state, then adjust the seat to your comfortable or pre-set position. Hold for about 3 seconds until the SET light turns on. Select memory position 1 or 2, and upon hearing a beep, the seat position will be memorized. The next time you drive, simply press the previously set 1 or 2, and the seat will automatically adjust to your preferred position. In some mid-to-high-end models with higher configurations, the driver's seat usually comes with a seat memory function, and this feature is very convenient and practical.
7
2
Share

How to adjust the front and rear of the BMW X3 driver's seat?

Under the driver's seat, there is a lever that can be pulled to adjust. For electric adjustment, the controls are located on the left side of the seat. First, adjust the seat and rearview mirror, then press and hold the M button. The optimal seat height should be determined based on various factors such as the driver's height, arm length, and the distance of the steering wheel from the body. If the distance between the seat and the pedals is too large, the driver's legs will be more comfortable, but the accuracy and force when stepping on the pedals will be compromised.
15
3
Share

What are the body dimensions of the XPeng P7?

XPeng P7 is positioned as a mid-to-large-sized coupe with a body length of 4880 mm. Below is a related introduction to the XPeng P7: 1. Design Concept: The XPeng P7 is positioned as a mid-to-large-sized coupe. The new car adopts the "Interstellar" series design language, featuring a closed front grille paired with a full-width light strip, giving it a strong technological feel. The fastback design perfectly matches its coupe identity and positioning. 2. Performance: The drag coefficient of the XPeng P7 is only Cd0.236, which is the lowest record among domestic Chinese cars, significantly enhancing its range capability.
4
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.