···
Log in / Register

Where is the cigarette lighter fuse located in the Arrizo 5?

3 Answers
June
07/24/25 10:41pm
The cigarette lighter fuse in the Arrizo 5 is located at the front left of the engine compartment. Here are the specific details about the Arrizo 5: 1. Exterior: The Arrizo 5 has a body length of 4572mm, width of 1825mm, height of 1482mm, and a wheelbase of 2670mm. 2. Powertrain: The Arrizo 5 is equipped with a 1.5L naturally aspirated engine with a maximum power output of 116 horsepower. It can be paired with either a 5-speed manual transmission or a 7-speed CVT transmission. The manual transmission features a gear shift reminder function, while the CVT transmission comes with an Economy mode (ECO) and Sport mode, providing a more diverse driving experience.
Was this review help?
20
4
Share
LeMatthew
08/10/25 10:15am
Last time, the cigarette lighter in my Arrizo 5 suddenly stopped working, and it turned out to be a blown fuse located in the fuse box under the driver's seat. Generally, after opening that small panel, you can see diagrams or labels on the cover. The cigarette lighter fuse is usually 10 or 15 amps, marked 'CIG' or '12V'. DIY troubleshooting is simple: first, turn off the engine and disconnect the negative battery terminal, then use plastic tweezers to pull it out and check. If it's blown, just replace it. The cigarette lighter fuse often blows due to overloading from car chargers or humidifiers, so using low-power devices can prevent this. If you can't find the box, sometimes there's a small compartment behind the glove box or on the left side of the dashboard, but the in-cabin location is more common. Safety first—don't operate with wet hands to avoid short circuits and issues.
Was this review help?
12
1
Share
Expand All
DelTanner
09/26/25 6:30am
The location of the cigarette lighter fuse is crucial. In the Arrizo 5, it's typically hidden in the front driver-side fuse box, near the door pillar or under the floor mat. Lift the panel to reveal it, and you'll find labels indicating the position—often F5 or F10 for the cigarette lighter. Remember to disconnect the power before replacement to prevent electric shock risks. If it's blown, check if the plugged device draws excessive current; otherwise, replace it with a new fuse of the same amperage. This position is designed for convenient owner maintenance, but avoid forcing it open if you can't find it to prevent damaging the wiring. Regularly inspect the fuse condition and keep the box clean to avoid poor contact caused by dust. Avoid temporary repairs while driving; it's safer to pull over and handle it.
Was this review help?
16
2
Share
Expand All
More Forum Discussions

Is it okay if the car scraped the chassis?

If the car scraped the chassis without any fluid leakage or mechanical deformation, it should be fine. The function of the chassis is to support and install the car engine and its various components and assemblies, forming the body shape, receiving the power from the engine to make the car move and maintain normal driving. The composition of the car chassis: it consists of the transmission system, steering system, driving system, and braking system. The maintenance methods for the car chassis are: 1. Check the oil condition of each important assembly in time; 2. Pay attention to the wear of brake pads and clutch plates; 3. Regularly perform four-wheel alignment; 4. Pay attention to the tire pressure and wear condition.
8
5
Share

How to Replace a Faulty Spark Plug?

To replace a faulty spark plug, follow these steps: 1. Wait for the engine to cool completely, open the hood, unplug the high-voltage pack connector, and remove the fixing bolts; 2. Use a socket wrench to loosen the nuts by turning counterclockwise; 3. Use a magnetic rod to extract the spark plug; 4. Attach the new spark plug to the magnetic rod and insert it into the hole; 5. Reassemble by following the above steps in reverse order; 6. Start the engine to check if the spark plug is functioning properly. The reasons for a faulty spark plug include: 1. Insufficient spark energy during ignition; 2. Excessive air-fuel ratio in the fuel mixture; 3. Overheating of the engine; 4. Dirty air filter; 5. Excessive idle speed; 6. Severe carbon buildup and use of low-quality gasoline; 7. Damaged valve oil seal or crankcase ventilation valve.
4
4
Share

Why is it difficult to engage reverse gear in a manual transmission?

The reasons why it is difficult to engage reverse gear in a manual transmission are: 1. The gear is not engaged and is in neutral; 2. The gear switch of the transmission is faulty; 3. The clutch is not fully depressed; 4. The synchronizer is not installed, causing the teeth to misalign with the gear; 5. The handbrake is not released, leaving the car in manual braking state. The steps to start a manual transmission car are: 1. After starting the car, press the clutch pedal all the way down with your left foot to completely disengage the clutch; 2. Shift the transmission into first gear; 3. Press or lift the electronic handbrake button; 4. Ensure safety by observing the road and other vehicles or pedestrians; 5. Continue to hold the clutch pedal with your left foot to keep the clutch disengaged, press the accelerator pedal with your right foot, and slowly release the clutch pedal with your left foot.
14
5
Share

What is the Volkswagen Teramont 330TSI?

Volkswagen Teramont 330TSI is the Volkswagen Touareg 330TSI model. Here are the specific details about the Volkswagen Touareg: 1. Powertrain: The Touareg is equipped with three powertrain options, including a 2.0T high/low-power version and a 2.5T V6 engine. The Touareg 330TSI model features a 2.0T engine with a maximum power output of 186 horsepower and a maximum torque of 320 Nm, paired with a 7-speed dual-clutch transmission. The power of the 330TSI model can meet the basic needs of daily driving. 2. Features: The vehicle comes with a multimedia information display that supports the App-Connect smartphone integration platform, compatible with Apple CarPlay and Android Auto. It also includes adaptive cruise control, lane keeping assist, blind spot monitoring, collision warning, heated steering wheel, front seat heating/ventilation, and a panoramic sunroof.
19
3
Share

What Causes the Jerking Sensation When Releasing the Clutch After Shifting Gears?

The reasons for experiencing a jerking sensation when releasing the clutch after shifting gears are: 1. Jerking during upshifting: The transmission's response speed is not fast enough, and the upshift speed cannot keep up with the driver's throttle input, resulting in a jerking sensation during gear changes. 2. Jerking during downshifting: When the driver releases the accelerator pedal or presses the brake pedal, the alternator starts working, placing a load on the engine and causing a mismatch between the engine speed and the clutch disc speed, leading to a jerking sensation. The working principle of the clutch is: 1. The torque generated by the engine is transmitted to the driven disc through the friction between the flywheel, pressure plate, and the contact surface of the driven disc. 2. When the driver depresses the clutch pedal, the diaphragm spring's large end moves the pressure plate backward through mechanical linkage, separating the driven components from the driving components.
20
4
Share

How to Turn Off a Motorcycle Alarm?

There are several methods to turn off a motorcycle alarm: you can directly use the key to turn on the power switch, which will deactivate the alarm state. When the key is not available, simply unplug the power connector and then plug it back in to deactivate the alarm state. Below is additional information about power locks: 1. By voltage: Power locks can be categorized into low-voltage power locks and high-voltage power locks based on voltage levels. Low-voltage power locks are mainly used in small appliances, electric toys, and electric vehicles. High-voltage power locks are primarily used in machine tools, elevators, etc. 2. By the number of controlled circuits: Power locks can be divided into single-circuit power locks, dual-circuit power locks, and multi-circuit power locks. A single-circuit power lock can only control one circuit. A dual-circuit power lock can simultaneously control two circuits.
17
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.