···
Log in / Register

Where is the cigarette lighter fuse in the Audi Q5?

4 Answers
Debra
07/23/25 1:05pm
Audi Q5 front row fuses are located above the driver's footrest, while the rear row fuses are on the side of the trunk. The specific position of the cigarette lighter is clearly marked on the inside of the fuse box cover. Below is the inspection tutorial: 1. Before inspection, completely turn off the engine and all electrical equipment. 2. Locate the corresponding position and use a small pry bar to open the protective cover. 3. Check the position of the cigarette lighter fuse on the cover. 4. There is no need to remove the fuse immediately; first, use a test pen to measure it. If one end lights up and the other does not, it is likely that the fuse has blown. 5. Use a clip-like tool to remove the blown fuse and then install a new one.
Was this review help?
3
5
Share
MacBrynlee
08/10/25 10:58am
I remember when I drove an Audi Q5, the location of the cigarette lighter fuse was very clear. It was in the fuse box near the driver's feet, under the dashboard—just lift the black cover gently. Inside, there were rows of small fuses, and the one for the cigarette lighter was usually labeled F50, a 15-amp type, sometimes with an icon as a hint. If the fuse blew, the cigarette lighter would stop working, often due to something like an overloaded car charger. I replaced it a few times myself—simple process: first, turn off the engine and remove the key to cut power, then use small tweezers to pull out the burnt fuse and replace it with a new one of the same rating. The manual is the best helper, showing the exact location; if you don’t have it, checking an online diagram works too. DIY is actually quite fun—keeping a few spare fuses in the car for emergencies avoids panic, but be careful not to overload the socket.
Was this review help?
16
3
Share
Expand All
BentleyMarie
09/22/25 4:42am
As a car owner, I'm quite adept at handling the cigarette lighter fuse issue in my Audi Q5. The fuse box is located on the left side of the driver's seat, and you can see it by opening the cover. The cigarette lighter fuse is usually in the F50 or F55 slot. Last time my cigarette lighter stopped working, I checked and found the fuse had blown because I was using a high-power refrigerator. The replacement process is straightforward: turn off the engine and power, locate and remove the old fuse, then insert a new 15A fuse in its place. The location isn't hard to find; you can refer to the Audi Q5 fuse layout diagram in the manual or search for it online, then save a screenshot on your phone for daily reference. To prevent future issues, try not to plug in devices that exceed the rated power, like electric drills. If you're unsure about the location, don't force it—drive to the 4S store and let the technician handle it for safety and peace of mind.
Was this review help?
2
4
Share
Expand All
MacAnastasia
11/05/25 8:02am
The cigarette lighter fuse for the Audi Q5 is located in the cabin fuse box, specifically under the driver's side footwell. Upon opening the cover, you'll find neatly arranged fuses, with the cigarette lighter typically labeled as F50, rated at 15 amps. If the fuse blows, the cigarette lighter will stop functioning, possibly due to overload or a short circuit. Before replacement, ensure the vehicle is turned off, gently remove the old fuse, and insert a matching new one. The manual serves as the authoritative source for accurate positioning. DIY replacement is simple and quick, and to prevent faults, avoid using high-power devices.
Was this review help?
9
4
Share
Expand All
More Forum Discussions

Can You Start the Engine If Water Enters the Exhaust Pipe?

If only a small amount of water enters the exhaust pipe, you can start the engine; however, if a large amount of water enters the exhaust pipe, it is recommended that drivers avoid starting the engine. Below is a detailed explanation: 1. Generally, a car's engine can be started as long as there is no water in the intake pipe. 2. If the water depth exceeds the height of the intake port, it is advised that drivers refrain from driving further. 3. Water entering the intake pipe can cause the engine to stall, and attempting to start it under such conditions may lead to connecting rod deformation or even cylinder perforation. 4. A small amount of water in the exhaust pipe usually does not pose a problem when starting the engine. After starting, you can press the accelerator to expel the water from the exhaust pipe once the engine temperature rises. However, if there is a significant amount of water in the exhaust pipe, it must be promptly removed to avoid damage to the catalytic converter.
3
0
Share

What does the yellow triangle with an exclamation mark in a car mean?

A triangle with an exclamation mark indicates a malfunction in the vehicle's general performance, components, or functions. Common issues include parking sensor failure, fuel cut-off system intervention or malfunction, external light failure, or engine oil pressure sensor failure. Solution: It is necessary to visit a 4S shop for inspection to identify the source of the fault. The exclamation mark is a common fault indicator in cars. Besides the triangle with an exclamation mark, there are four other forms of exclamation mark warnings: a yellow gear with an exclamation mark, a red circle with parentheses and an exclamation mark in the middle, a yellow bracket with a horizontal line and an exclamation mark in the middle, and a yellow bulb with an exclamation mark. Below is a detailed analysis of these four scenarios: Automatic Transmission Fault: A yellow gear with an exclamation mark indicates an automatic transmission fault warning light, signaling a transmission malfunction or transmission lubricant level below the normal range. The transmission fluid should be replaced promptly. Brake System Fault: A circle with parentheses and an exclamation mark in the middle represents a brake system warning, typically indicating a brake system malfunction or low brake fluid level. Immediate inspection of the brake system is required to avoid accidents. Tire Pressure Anomaly: A bracket with a horizontal line and an exclamation mark in the middle represents the tire pressure monitoring warning light. This light turns on when the tire pressure is too low. Check the tire pressure and restore it to the normal range. Lighting Fault: A yellow bulb with an exclamation mark indicates a lighting fault warning, signaling a malfunction in one of the vehicle's lights. Solution: Visit a 4S shop as soon as possible for inspection and repair. Alternatively, you can perform a self-check, focusing on commonly used bulbs such as turn signals, fog lights, and interior lights, to identify the issue.
2
0
Share

How to Reinstall a Car Seat After Removal?

The method for reinstalling a car seat after removal is as follows: 1. For seatbelt-type car seats, installation requires certain skills and can be done in two ways: forward-facing and rear-facing, with rear-facing installation being more suitable for infants. 2. Thread the seatbelt through the seat and secure it with the seat's red locking clip. This function is used to fix the seatbelt, preventing it from sliding and failing to secure the seat properly, then insert the connector. Below is relevant information about car seats: Removal method: 1. After removing the car seat from the vehicle, adjust the shoulder straps to a relatively loose state. 2. Check the back of the seat to find the harness hooks, remove the harness from the fixed hooks at the adjustment position on the back of the seat, and store the hooks properly to avoid loss. 3. Remove the headrest fabric cover by pulling it out from the installation slot. 4. Take out the fabric cover on the seat cushion, similar to the headrest cover, by pulling it out.
7
3
Share

Abnormal Noise When Shifting Gears in Automatic Transmission?

Abnormal noise when shifting gears in an automatic transmission is generally caused by the following reasons: 1. The vehicle was not completely stopped before shifting. When parking, the vehicle should be brought to a complete stop before shifting the gear lever from D (Drive) to P (Park). If the vehicle is shifted to P before it is fully stopped, the P gear lock hook inside the transmission will strike the gear, producing a clunking sound. This operation can cause wear or even breakage of the lock hook, and in severe cases, may lead to transmission failure. 2. Incorrect operation sequence when parking on a slope. For automatic transmission vehicles, the P gear relies on the lock hook engaging the gear to keep the vehicle stationary. When parking on a slope, the handbrake should be engaged first before shifting to P, allowing the handbrake to bear the vehicle's sliding force. If P is engaged before the handbrake, the entire sliding force of the vehicle will be borne by the P gear lock hook, putting tension on the lock hook and gear. In this case, shifting from P to other gears will produce a noise.
9
5
Share

How Many Kilowatt-Hours Does It Take to Fully Charge a Pure Electric Vehicle?

This depends on the vehicle's battery capacity. Different new energy vehicles have varying battery capacities, so the amount of electricity required for a full charge cannot be generalized. Below are the relevant explanations: 1. Electric vehicles are divided into AC electric vehicles and DC electric vehicles. 2. Electric vehicles typically use batteries as their energy source, converting electrical energy into mechanical energy through components such as controllers and motors to drive the vehicle. 3. Electric vehicles align with the national trend of energy conservation and environmental protection, playing a significant role in China's environmental conservation and protection efforts. 4. Over a decade ago, electric vehicles were developed as a green industry in China, growing at an annual rate of 30%. 5. Due to their obvious advantages, electric vehicles have become popular among urban low- and middle-income groups. In recent years, the electric vehicle market has maintained rapid growth, with new energy vehicles achieving mass production, gradually bringing the technology of the electric vehicle industry to international advanced levels.
3
5
Share

How to Deal with the Sour and Musty Smell in Car Air Conditioning?

Solutions for the sour and musty smell in air conditioning: 1. Replace the car air conditioning's air filter element, ensuring regular cleaning and replacement. 2. Clean the ventilation ducts, preferably when replacing the air filter element. 3. Clean the blower, ideally performed by professionals to avoid damage. 4. Clean the car interior, paying more attention to the hygiene inside the car. 5. Turn off the cooler before parking and dry the evaporator and ventilation ducts. These measures can effectively prevent the issue and extend the evaporator's service life. Note: A strong sour and musty smell in the car air conditioning is often caused by problems in the air conditioning system, such as severe contamination of the air filter element, excessive humidity inside the evaporator box, or accumulation of dust and impurities in the air conditioning vents.
2
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.