Where is the cigarette lighter fuse in Audi A4L?

3 Answers
Allison
07/23/25 9:40pm
Audi A4L cigarette lighter fuse location: The front row fuse is located above the driver's foot pedal, and the rear row fuse is on the side of the trunk. The inner side of the fuse box cover will clearly indicate the position of the cigarette lighter fuse. Fuses control the current and voltage of various components. Improper installation may easily burn out the fuse or even cause a fire, so it is not recommended for non-professionals to replace it. The Audi A4L is a model officially released by Audi on November 16, 2008. It features a brand-new exterior and chassis design, with front-end styling inspired by the Audi S series, a coupe-like streamlined body, wide wheels, and bold wheel arches, making it appear dynamic, elegant, steady, and full of tension in traffic.
Was this review help?
14
4
Share
DeLeonardo
08/10/25 5:19pm
Let me tell you, I've encountered the issue of locating the cigarette lighter fuse on an Audi A4L several times. It's usually in the fuse box near the driver's footwell—just look down and you'll see a small cover below the dashboard. Gently pry it open, and you'll find all the fuse slots inside. According to the manual, the cigarette lighter fuse is typically labeled with an "F," such as F38 or something similar. Don't rush into it—make sure to turn off the engine and remove the key first to avoid electric shock. If the fuse is blown, you can replace it yourself with needle-nose pliers, but be careful not to use the wrong specification. The exact location might vary slightly depending on the model year, so keeping a phone flashlight handy helps. Overloading the cigarette lighter is common, so regular checks can prevent trouble. If you still can't find it, heading straight to the dealership is the easiest solution. Safety comes first—handle everything gently and avoid forcing anything.
Was this review help?
19
1
Share
Expand All
GageRose
09/23/25 5:14am
Speaking of the fuse location for the Audi A4L cigarette lighter, I tried it myself once. It's in the car's interior fuse box, specifically near where you press the accelerator pedal while driving. There's a panel at the bottom of the dashboard; just pop it open. The fuse is usually marked as the cigarette lighter or has a number like F39. I recommend checking the owner's manual before you start—it has detailed diagrams. Don't operate while the car is running; turn off the engine and wait a few minutes for cooling. Blown fuses are common, often triggered by frequent use of the cigarette lighter plug or voltage fluctuations. Replacing it is simple—just buy the same type and plug it in. Remember, locations can vary; also check the fuse boxes in the trunk or engine compartment. Regular maintenance of the cigarette lighter can extend the fuse's lifespan. If in doubt, consult a professional at a shop—don't take risks by tinkering randomly.
Was this review help?
13
5
Share
Expand All
More Forum Discussions

How to Solve the Engine Immobilizer Authentication Failure Issue on Baojun 510?

Fellow car owners should first check their car keys. The remote key fob contains a dedicated module specifically for engine starting. Simply pry open the casing, remove the old battery and replace it with a new one.
8
1
Share

How to Remove the Fuel Pump on a Buick Excelle?

First remove the rear seat to expose a black metal cover secured by four screws. Unscrew these to reveal the fuel pump. Disconnect all wiring connections, then use a specialized fuel pump removal tool to unscrew and extract the unit.
9
1
Share

How to fix the peeling dashboard of a Buick Excelle?

If the dashboard warping issue occurs during the car's warranty period, you can contact after-sales service for relevant handling. If the car's warranty period has expired but the dashboard warping issue occurs, you can go to an auto repair shop for handling.
13
2
Share

What Causes the ABS Light to Illuminate in a Jaguar?

ABS light illumination can occur in various states, with different causes and solutions for each state, as detailed below: State 1: ABS warning light remains constantly lit (most common). Cause 1: The ABS wheel speed sensor's sensing area is covered by dirt, mud, or other contaminants, affecting the sensor's ability to detect the corresponding speed signal. This prevents the ABS control unit from determining the vehicle speed and wheel slip rate, thus failing to issue appropriate commands to regulate braking. Solution: Clean the contaminants from the wheel speed sensor and adjust the gap between the sensor and the signal ring to restore normal operation. Cause 2: Poor signal transmission due to loose system wiring connections or poor contact in the ABS relay, leading to system malfunction. Solution: Inspect wiring connections and reconnect any loose parts. State 2: ABS warning light intermittently illuminates but turns off during acceleration. Cause: When multiple electrical components are in use, the battery voltage drops below 10.5V. As engine speed increases, voltage rises, and the ABS light turns off. This may also occur due to insufficient power supply voltage to the ABS system, such as poor terminal contact or grounding issues. Solution: Check the battery's specific gravity; inspect the charging system; examine the power supply (e.g., voltage relay or poor power contact). State 3: ABS warning light remains lit after engine startup until the engine is turned off (IGFF). Cause: Poor grounding contact in the ABS hydraulic valve body; poor electrical connector contact in the ABS hydraulic valve body; ABS control unit malfunction. Solution: Loosen and then retighten the grounding screw on the hydraulic valve body, cleaning the contact surface if necessary; check for enlarged connector gaps; replace the ABS or ABS/ASR control unit. State 4: ABS warning light illuminates during high-speed driving. Cause: During high-speed driving, the ABS control unit detects a significant discrepancy between rear and front wheel speed signals; incorrect tire or wheel rim specifications. Solution: Refer to the vehicle's specified tire and wheel rim specifications, typically listed on the fuel tank cap sticker. State 5: ABS warning light intermittently illuminates. Cause: Improper adjustment of the brake light switch; poor internal contact in the brake light. Solution: With the engine running, press the brake pedal and manually push the brake switch linkage fully downward, then release the pedal to complete self-positioning; replace the brake light switch if necessary. If the ABS warning light is illuminated, it is advisable not to continue driving. An illuminated ABS light indicates a malfunction in the vehicle's anti-lock braking system. During emergency braking, if the wheels lock up, the vehicle may skid uncontrollably, preventing the driver from slowing down or adjusting the vehicle's trajectory, posing significant safety risks.
17
1
Share

How to adjust the ambient lighting in the 2021 Audi A6L?

You can adjust the interior ambient lighting through the MMI display. Press the CAR button to select the system and enter the background lighting interface. The ambient lighting at the front footwells, rear footwells, front door panels, and rear door panels can all be set via the MMI.
2
0
Share

How to Repair Cracked Leather in Car Interior?

Use a soft brush and a slightly damp towel to thoroughly clean the leather that needs repair or has wrinkles. Sand the leather surface that requires repair with water sandpaper, and remove any already cracked leather as well. Apply leather repair paste to the surface that needs fixing, spray a layer of primer on the leather surface, then complete the coloring within 60-150 seconds.
13
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.