Where is the child lock located in the car?

2 Answers
Amir
07/24/25 9:37pm
Child locks are typically located in the window button area on the driver's side door or on the inner edge of the rear doors. How to use: To activate the child safety lock, first open the rear door, gently push the small lever below the door lock in the direction of the child icon, then close the door. The function is that when the child safety device is in the locked state, the door can only be opened from the outside, and the inner door handle temporarily loses its ability to open the door. Additional information: When the car child safety lock is in the locked state, it will remain locked even if the central locking system is unlocked. The door can only be opened from the outside. If you find that the rear door cannot be opened from inside the vehicle while it opens normally from the outside, you should check whether the child safety lock has been accidentally activated.
Was this review help?
4
3
Share
Pereira
08/10/25 2:43pm
As a new parent, I was particularly concerned about the location of the child safety locks when I first started traveling with my baby. This feature is usually located on the side of the car's rear door, specifically on the small switch inside the door frame when the door is open. It might be a bit tricky to find at first, but once you open the rear door and carefully inspect the door edge or the inner side, you'll notice a small toggle or rotary knob icon. The operation is straightforward: simply switch it to the locked position to prevent children from accidentally opening the door from the inside. This is extremely important, especially when kids are being mischievous, as it stops them from playing with the handle while the car is moving, which could be dangerous. I recommend checking all rear door switches before every trip, as both left and right doors may need to be set independently. The exact position can vary slightly depending on the car model—some might be hidden in door panel grooves—but once you get familiar with it, it becomes second nature. Safety is always a top priority, so don’t overlook this small detail; it can save you a lot of hassle.
Was this review help?
10
1
Share
Expand All
More Forum Discussions

Can You Drive with Damaged Tire Pressure?

Tire pressure is compromised, can you still drive? If possible, drive to the nearest tire repair shop for assistance. If the tire pressure is too low to continue driving, it is recommended to use a car air pump to inflate the tire slightly before heading to the nearest repair shop. Alternatively, you can replace it with a spare tire and then proceed to a repair shop. Below are the hazards of driving with low tire pressure: 1. Increased friction coefficient with the road surface, leading to higher fuel consumption; 2. Causes the steering wheel to become heavy and prone to deviation, posing risks to driving safety; 3. Increases movement in various parts of the tire, leading to excessive rolling and abnormal heat generation; 4. Reduces the functionality of the tire's cords and rubber, potentially causing delamination or cord breakage, as well as excessive friction between the tire and rim, resulting in damage to the tire bead and abnormal wear.
8
5
Share

Where is the water filler port for the Toyota Corolla's radiator?

The radiator filler port for the Corolla is located on the left side of the engine compartment near the passenger seat. The car radiator generally refers to the automobile heat exchanger, which is part of the vehicle's cooling system. The radiator in the engine's water cooling system consists of three main components: the inlet chamber, outlet chamber, main plate, and radiator core. The steps for adding water to the car radiator are as follows: 1. Turn the pressure cap counterclockwise; if you hear a hissing sound, wait until the sound stops before opening it; 2. Fill the coolant expansion tank with an appropriate amount of coolant, ensuring the level is between the MAX and MIN marks; 3. With the coolant expansion tank cap open, start the engine; 4. After starting the engine, the coolant level in the tank will gradually decrease. At this point, add more coolant to the expansion tank until the level reaches between the MAX and MIN marks again; 5. Reinstall the cap, making sure it is hand-tightened and fully seated.
7
1
Share

What is the penalty for having two people in the front passenger seat?

Having two people in the front passenger seat is considered overloading, and if caught by traffic police, it will result in corresponding fines and penalty points. Precautions for sitting in the front passenger seat are as follows: 1. Proper use of seat belts: Generally, the front passenger seat is more comfortable, spacious, and offers a view of the scenery ahead. Therefore, passengers sitting in the front seat tend to be more relaxed. For example, reclining the seat back too low, almost turning it into a lounge chair, while still wearing a seat belt is equivalent to tying a noose around oneself. In case of an emergency, sudden braking can cause the passenger to lunge forward due to inertia, and the seat belt can easily strangle the passenger's neck, potentially causing severe injury. 2. Pay attention to sitting posture: While enjoying the comfort of the front passenger seat, it is crucial to maintain a proper sitting posture. This ensures that the seat belt and airbag can function effectively in case of danger. Some passengers in the front seat recline halfway, place their feet on the dashboard, or even press against the windshield, which is extremely dangerous. A sudden brake could shatter the windshield or eject the passenger. 3. Avoid letting children sit in the front passenger seat: If a child must sit in the front, ensure the seat belt is properly fastened and adjusted to the correct length. Additionally, if the front passenger seat has an AirBag, make sure to lock it to prevent injury to the child in case of an emergency.
18
4
Share

What to Do When the Buick Excelle Tire Pressure Monitoring Alarm Goes Off?

When the Buick Excelle tire pressure monitoring alarm goes off, the first step is to check if the tire pressure is too low. If the tire pressure is normal, you can turn off the monitoring light by resetting the tire pressure monitoring system. If there is indeed a serious air leak, such as a punctured tire, you will need to replace the spare tire or contact road assistance directly. The steps to reset the tire pressure monitoring are as follows: 1. Park the vehicle and engage the handbrake; 2. With the vehicle powered on, press the "MENU" button on the turn signal lever to switch the small screen on the dashboard to the "Vehicle Information" section; 3. Use the up and down selection buttons on the turn signal lever to find the tire pressure information section. 4. Press and hold the "SET/CLR" function button at the head of the turn signal lever until the message "Start tire pressure learning?" appears, then select "Yes." 5. After selection, the horn will sound twice to confirm that the tire pressure learning has started, and the left front turn signal will light up.
4
2
Share

How many questions can you get wrong in Subject 4?

According to the 'Regulations on the Application and Use of Motor Vehicle Driving Licenses', for the Subject 3 road driving skills and safe civilized driving knowledge test, a score of 90 points is required to pass. Each incorrect answer deducts 2 points, meaning you can only get 5 questions wrong to pass, with a full score of 100. Questions 1-10 are true/false; questions 11-40 are single-choice; and questions 41-50 are multiple-choice. The test includes image analysis, animated case studies, and text descriptions. The scope of Subject 4 covers driving knowledge in adverse weather and complex road conditions; identification of common traffic signs, markings, and hand signals; accident rescue and hazardous material handling; comprehensive judgment of illegal behaviors and case analysis; emergency avoidance knowledge; safe driving knowledge; and driving ethics and civilized driving knowledge. According to the 'Regulations on the Application and Use of Motor Vehicle Driving Licenses', there is no limit to the number of attempts for Subjects 1 and 4. If you fail the first attempt on the same day, you can retake it immediately. If you still fail, you need to reschedule, with no fee for retakes. However, note that the driving skill test permit is valid for three years. If the applicant does not complete the test within this period, the passed subject scores will be invalidated. Subject 4, also known as the Subject 4 theory test or driver theory test, is part of the motor vehicle driving license assessment. After the implementation of the Ministry of Public Security's Order No. 123, Subject 3 was divided into two parts: the road test and the safe civilized driving knowledge test, commonly referred to as 'Subject 4', which assesses 'driving ethics'. Subject 4 is the colloquial term for the Subject 3 safe civilized driving knowledge test and is not a separate subject. Since this test follows Subject 3, it is commonly called Subject 4. Officially, there is no Subject 4. The safe civilized driving knowledge test is conducted after Subject 3. Subject 4 Test Notes: Test Duration: The test lasts 45 minutes. Number of Questions: 50 questions are selected proportionally from the Subject 4 question bank based on the type of license being tested. Question Types: The test includes single-choice questions (including true/false) and multiple-choice questions, with questions presented as animations, images, scenario recognition, or text descriptions. Retake Notes: Failing Subject 4 only requires retaking Subject 4. The driving school will schedule the retake, with no limit on attempts and no retake fees. The driving test consists of three subjects: Subject 1, Subject 2, and Subject 3, with Subject 3 divided into two parts. Subject 1 covers traffic safety laws, regulations, and related knowledge; Subject 2 is the field driving skills test; and Subject 3 includes road driving skills and safe civilized driving knowledge.
1
5
Share

How to Check the Manufacturing Year of Tires?

The method to check the manufacturing year of tires is as follows: 1. There is a set of numbers on the tire wall, and the last four digits of this mark can provide information about the production date, consisting of four digits "AABB". The first two digits "AA" indicate the week of the year, and the last two digits "BB" indicate the year. If these corresponding marks cannot be found on the tire due to non-standard installation, it means the tire is mounted in the wrong direction. 2. Tires are usually composed of three parts: the outer tire, inner tube, and flap. There are also tubeless tires, which have an inner layer of airtight rubber in the tire body and require special rims. The structure of tires worldwide is evolving towards tubeless, radial, flat (small ratio of tire section height to width), and lightweight designs.
14
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.