Where is the Changan Oushang X5 manufactured?

Should I Inflate My Tires to 2.1 Bar in Autumn?

Autumn tire pressure of 2.1 bar requires inflation. Winter temperatures are relatively low, and due to thermal expansion and contraction, tire pressure will also change. Generally, the normal range of tire pressure is around 2.5 bar, which can be set as usual. However, after entering winter, the tire pressure should be increased slightly. Generally, adjusting it to 2.6 bar is the most suitable and safest range. Tire pressure standards for different tires: Standard tires: 2.4-2.5 bar; Reinforced tires: 2.8-2.9 bar; Maximum pressure: Should not exceed 3.5 bar. Normal winter tire pressure: In winter, adjust the tire pressure based on the standard tire pressure of the car tires, increasing it by about 0.2 bar. Normal summer tire pressure: Generally, the lower limit of the standard tire pressure for car tires is sufficient. For example, the lower limit for standard tires is 2.4 bar. If the car is often parked outdoors, the tire pressure can generally be about 0.1 bar lower than the standard to avoid tire blowouts due to high temperatures.

11

5

Share

Why aren't the high-speed gantry-mounted spotlights canceled?

Gantry structures don't significantly impact safety and serve irreplaceable functions, hence they haven't been removed. Gantries provide supplementary lighting: The spotlights mounted on gantries, also called fill lights, enable the license plate capture systems installed on these structures to take clearer photos with more substantial evidence. As the name suggests, highways involve higher vehicle speeds, where traffic violations become more dangerous when occurring at such velocities. Meeting illumination requirements: Fill lights should ensure uniform illumination within their coverage area, without dark spots or noticeable flickering. At 20 meters from the lighting device, the peak illuminance on the reference axis should be below 300lx, with average illuminance under 50lx, and visible light color temperature between 3000-5500K. This brightness level is roughly equivalent to that of an ordinary streetlight.

6

5

Share

Do I need to affix the new vehicle annual inspection sticker?

In regions where electronic stickers are implemented, the new vehicle annual inspection sticker does not need to be affixed. In 2020, electronic inspection labels were fully promoted to replace the paper version of the annual inspection pass sticker. Electronic inspection labels and paper annual inspection stickers have the same legal effect. In provinces and cities that have implemented electronic annual inspection stickers, the inspection pass sticker does not need to be affixed. Regions without electronic stickers: In areas where electronic inspection labels have not been implemented, the inspection pass sticker must continue to be affixed. Penalties for not affixing the inspection pass sticker: According to Article 13 of the "Regulations for the Implementation of the Road Traffic Safety Law": The motor vehicle inspection pass sticker and insurance sticker shall be affixed to the upper right corner of the front window of the motor vehicle. Failure to affix the relevant vehicle stickers as required is a violation of the law. If the annual inspection sticker is not affixed, a penalty of 1 point deduction and a fine will be imposed. Placing it on the dashboard will also result in a fine. Affixing the annual inspection sticker will result in a penalty of 1 point deduction and a fine, and placing it on the dashboard will also result in a fine.

1

0

Share

What is the mnemonic for the Subject 3 lighting test?

Subject 3 lighting simulation mnemonic is as follows: High beam: When driving on roads with low visibility, use the high beam correctly. On poorly lit or unlit road sections, the high beam can be used. Alternating high and low beams: When passing sharp curves, slopes, arched bridges, or crosswalks at night, alternate between high and low beams no less than 2 times. When passing intersections without traffic signals at night, alternate between high and low beams no less than 2 times. When overtaking vehicles ahead at night, alternate between high and low beams no less than 2 times. Position lights and hazard warning lights: For temporary parking on the roadside, use position lights + hazard warning lights. In case of vehicle malfunction that obstructs traffic and is difficult to move, use position lights + hazard warning lights.

5

2

Share

Why Is the First Year Insurance More Expensive for a Transferred Vehicle?

The reason why the first year insurance is more expensive for a transferred vehicle is: Compared to a new car, the performance of a used car has a significant gap, and once a used car is involved in an accident, the resulting losses are much greater than those of a new car. Therefore, according to the calculation rules of insurance premiums, the insurance cost for a used car will be relatively higher. Price Affects Premiums: The price of the used car will also affect the insurance cost to some extent. Additionally, the high insurance cost is mainly due to the variety of insurance types involved in vehicle transfer. Remember to Get the Insurance Policy When Transferring Insurance: After the vehicle insurance is transferred, the claim history of the traded vehicle is also very important. A car with a claim history often has higher insurance premiums than one without. Therefore, it is crucial to request the original insurance policy from the previous owner. If the vehicle had previous accidents that were overlooked, the new owner will have to bear the additional insurance costs.

4

3

Share

Does the high beam next item need to be reset for high-low beam switching?

For the high beam next item to switch between high and low beams, first switch the light to low beam mode, then activate the high-low beam switching mode. Method to turn on high and low beams: The light control lever has an image showing a straight line indicating high beam; gently push the lever located at the lower left of the steering wheel forward with your finger to activate high beam. When you pull the lever back, the dashboard will show that it has returned to low beam. To enable automatic headlights: Some models of the Qoros 5 are equipped with automatic headlight functionality. Adjust the headlights to automatic mode, and they will turn on and off automatically based on outdoor light conditions.

12

0

Share

Where is the Changan Oushang X5 manufactured?

Should I Inflate My Tires to 2.1 Bar in Autumn?

Why aren't the high-speed gantry-mounted spotlights canceled?

Do I need to affix the new vehicle annual inspection sticker?

What is the mnemonic for the Subject 3 lighting test?

Why Is the First Year Insurance More Expensive for a Transferred Vehicle?

Does the high beam next item need to be reset for high-low beam switching?

What are the functions of a mechanical transmission system in automobiles?

What does manufacturer model mean?

How Many Days Does It Take for the Used Car Electronic Records to Arrive?

What does a pedestrian crossing sign look like?