Where is the car's low beam light located?

1 Answers
Sarah
07/30/25 9:31am
Low beam light switch is generally located on the left side of the dashboard, near the door. Turning it one notch activates the low beams. Definition of low beam: The illumination distance of low beam is approximately 30-40 meters. Experiments show: when driving at 55 km/h at night, if you immediately apply the brakes upon detecting an obstacle, the stopping distance is exactly 30 meters. This means if you stop immediately upon spotting something within the low beam's illumination range, there will be no gap between the vehicle and the object. Function of low beam: Although low beams have an illumination range of about 30 meters, they feature a very distinct cutoff line between light and dark. Measurements show most car low beams illuminate 30-40 meters, with the cutoff line appearing at 12-18 meters. The area before the cutoff line is brightly lit, allowing clear object identification, with a visible 2-3 meter diameter illuminated area on the ground. The region from the cutoff line to 30-40 meters mainly relies on ground-reflected light, where brightly colored objects can be distinguished, but stationary dark-toned objects on the road surface are harder to detect.
Was this review help?
2
2
Share
More Forum Discussions

How to Adjust the Time on Chery QQ3?

The steps to adjust the time on Chery QQ3 are: 1. Start the vehicle and press the time adjustment button on the right side of the dashboard; 2. Hold down the time adjustment button without releasing it, the hour digits will start flashing, then press the time button briefly to adjust the hour digits; 3. After adjusting the hour accurately, release the time adjustment button, and after a few seconds the minute digits will start flashing; 4. Press the time adjustment button briefly again to adjust the minute digits accurately. The body dimensions of Chery QQ3 are: length 3550mm, width 1495mm, height 1530mm, wheelbase 2340mm, minimum ground clearance 152mm, and fuel tank capacity 35l.
7
5
Share

How to Solve the Problem of Windshield Wipers Not Cleaning Properly?

Solutions for windshield wipers not cleaning properly: 1. Remove the car's wipers, ensuring the car is turned off during the process; 2. Prepare water sandpaper, a small piece is sufficient for each wiper repair; 3. Soak the wiper and water sandpaper in clean water, then sand the wiper with the water sandpaper. When sanding, not only sand the two sides of the wiper but also appropriately sand the front of the rubber strip. The sanding time should not be too long, 5 minutes is sufficient. The reasons for wipers not cleaning properly are: 1. The windshield is not clean; 2. The wiper rubber strip is rough; 3. Improper use of the wipers.
17
1
Share

What is the weight of the Haval H6?

Haval H6 with a 2.0L engine has a body weight of 1520kg, while the 2.0T version weighs 1615kg. The Haval H6 is an SUV under Great Wall Motors, with body dimensions of 4640mm in length, 1825mm in width, and 1690mm in height, and a wheelbase of 2680mm. It is equipped with both gasoline and diesel engines, paired with a 7-speed dual-clutch transmission. The Haval H6 comes in three versions: Urban, Elite, and Premium, with body colors including Simple White, China Red, Hamilton White, Elegant Silver, Crystal Black, Cocoa Brown, Caney Blue, Mars Red, Modern Gray, Classic Black, and Wisdom Brown.
8
5
Share

How Much Difference Between NEDC Range and Actual Range?

NEDC range differs from actual range by 80%-90%. Below is an introduction to NEDC: 1. Introduction: NEDC stands for New European Driving Cycle, which translates to "New European Driving Cycle" in Chinese. It can be seen that the current range standard used by China's Ministry of Industry and Information Technology is the European standard. 2. Testing: The NEDC range test mainly simulates urban and suburban environments, with a ratio of 4:1. Due to the many influencing factors in actual road conditions, NEDC tests are mostly conducted on test benches. 3. Reference Value: The biggest criticism of NEDC is that the data produced by this theoretical method can sometimes be far from reality, and the standard NEDC reference value is not high in most countries.
8
0
Share

What does the 't' in 2.0t mean?

The 't' in 2.0t stands for turbocharging in a car engine. Here are the relevant explanations: Function: Turbocharging is essentially an air compressor designed to increase the engine's output power. Without altering the engine's cylinder capacity, it achieves this by increasing the compression ratio of the air entering the cylinders. Working principle: It utilizes the exhaust gases from the engine's exhaust port to drive the turbine wheel inside the turbocharger. This turbine wheel is directly connected to the compressor wheel in the compressor housing. One end of the compressor housing is connected to the air filter, while the other end compresses the air drawn from the filter into the engine's cylinders, thereby increasing the amount of air inside the engine.
13
3
Share

How many kilometers can 35 liters of fuel run?

35 liters of fuel can run 700 kilometers. The main factors affecting fuel consumption are as follows: Vehicle-related reasons: As the internal control unit of the car, the oxygen sensor mainly monitors the fuel-air ratio of the engine. Once it is damaged, it will cause an imbalance in the fuel-air ratio, leading to a sudden increase in fuel consumption. After the oxygen sensor is damaged, the exhaust pipe will emit darker-colored exhaust gas during driving. "Three filters" not replaced for a long time: During vehicle use, the three filters (oil filter, air filter, and fuel filter) must be replaced regularly. If they are not replaced for a long time, they will become dirty and affect performance, sending incorrect information to the engine control unit, resulting in incomplete fuel combustion and increased engine carbon deposits.
19
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.