Where is the car airbag plug located?

How to Replace the Cabin Air Filter in a Haval H2?

Haval H2's cabin air filter is located behind the glove compartment on the right side of the driver's cabin. You can see it after removing the glove compartment. The steps to replace the cabin air filter in a Haval H2 are as follows: 1. First, remove the glove compartment. 2. Then lift off the sponge protective panel. 3. Push the filter bracket firmly to detach it. 4. Next, take out the old cabin air filter, replace it with a new one, and reassemble by reversing the previous steps. The Haval H2 is a compact SUV produced by Great Wall Motors, equipped with a 1.5-liter turbocharged engine across all variants. Transmission options include a 6-speed manual or 7-speed dual-clutch, and it utilizes front-wheel drive configuration.

9

3

Share

How to Remove the Santa Fe Airbag?

Prepare a small flat-head screwdriver. Locate the three small disassembly holes for the airbag at the front left and right positions below the car's steering wheel. Align the screwdriver with the metal strip inside the disassembly hole and push it in to widen the gap on the left side of the driver's airbag. Repeat this method to remove the metal strips on the right and front sides. Pull open the black plastic strip that secures the wiring harness to detach it, then unplug the white horn grounding connector. Disconnect the plug connected to the airbag to complete the airbag removal process.

7

4

Share

How to Start a Haval Car When the Battery is Dead?

Before attempting a push start, first check if the road conditions where the vehicle is parked are suitable for push starting. Avoid push starting on roads with heavy traffic. Contact your insurance company by phone. Most insurance companies now offer free emergency services. If you have jumper cables in your car, you can ask for assistance from passing vehicles to give you a jump start. Prepare red and black cables. Connect the red cable to the positive terminal of the dead battery and the positive terminal of the assisting battery, and the black cable to the negative terminal of the dead battery and the positive terminal of the assisting battery.

9

1

Share

What is the best engine oil for Changan CS35?

CS35 requires SL grade 5W-30 viscosity engine oil during maintenance, with an oil volume of 3.4L. After filling, the oil level on the dipstick should be at the middle mark. Below are precautions for adding engine oil to the car: Always use the original manufacturer's recommended oil. Different types of engine oil should not be mixed, as this may interfere with the normal operation of the engine, and in severe cases, damage the engine and reduce its service life. The following are the steps for changing the engine oil: 1. Remove the oil cap. 2. Place an oil pan under the drain plug. 3. Use a wrench to loosen the drain plug and drain the oil. 4. After the oil is completely drained, reinstall the drain plug and tighten it to the specified torque (55±5N.m). 5. Slowly add engine oil through the oil filler hole until it reaches the upper limit on the dipstick. 6. Use an absorbent cloth to wipe off any spilled oil and cover the oil filler cap. 7. Start the engine and let it idle for 1 minute, then turn it off and wait for 5 minutes before checking the dipstick again.

9

4

Share

How to Find the VIN Number of a Verano?

Check the vehicle identification number (VIN) on the vehicle's motor vehicle license. There is a section that records it, labeled as the Vehicle Identification Number (VIN) code. The most common general location is on the left side of the dashboard. For sedans, the vehicle identification code is usually located below the outside of the driver's windshield, specifically in the lower right corner of the windshield. On various nameplates in the engine compartment, the VIN is generally located at the lower left corner of the front windshield, or on the driver's side door hinge pillar, door lock pillar, or door edge. Check other places, such as the insurance policy or the driver's side door pillar, for the vehicle identification code.

2

5

Share

How to Remove the Gear Shift Knob of Jetta Partner?

Prepare a pair of pliers and a flathead screwdriver. Pull the gear shift cover backward and then slowly lift it up to open the gear shift cover. Gently lift the cover and the leather of the gear shift to find the connecting clip. With the help of the pliers, release the clip, then remove the old gear shift knob and leather, and clean the dirt and dust around the gear shift. Use the screwdriver to remove the screws on the gear shift one by one.

20

0

Share

Where is the car airbag plug located?

How to Replace the Cabin Air Filter in a Haval H2?

How to Remove the Santa Fe Airbag?

How to Start a Haval Car When the Battery is Dead?

What is the best engine oil for Changan CS35?

How to Find the VIN Number of a Verano?

How to Remove the Gear Shift Knob of Jetta Partner?

What is the best oil for a Corolla 1.6?

What engine does the RAV4 use?

What is the fuel consumption of the 3.6L Wrangler?

What are the reasons why a car air conditioner cannot cool?