Where is the camshaft position sensor located on the old Jetta?

1 Answers
Robinson
07/29/25 7:12pm
The camshaft position sensor on the old Jetta is located at both ends of the right side of the engine. Information about the camshaft position sensor is as follows: Camshaft position sensor: It is a sensing device, also known as a synchronization signal sensor. Function: It is a cylinder identification and positioning device that inputs camshaft position signals to the ECU and serves as the main control signal for ignition. Information about the Jetta is as follows: Jetta: (Jetta) is a car brand under FAW-Volkswagen Automotive Co., Ltd., a joint venture of the German Volkswagen Group in China. Types: Currently, it includes 9 models with three displacements of 1.4L, 1.5L, and 1.4TSI, featuring 5-speed manual, 6-speed automatic, and 7-speed dual-clutch transmissions, equipped with Volkswagen's latest generation EA211 series engines.
Was this review help?
5
0
Share
More Forum Discussions

Is the engine of the Leiling the same as that of the Corolla?

The engine of the Leiling is the same as that of the Corolla. Not only the engine, but the three major components of the Leiling and Corolla are also the same, which include the engine, transmission, and chassis. Apart from some differences in appearance, there are almost no other differences between the Leiling and the Corolla. The dimensions of the Corolla are 4620mm in length, 1775mm in width, and 1480mm in height, with a wheelbase of 2700mm. The dimensions of the Leiling are 4640mm in length, 1780mm in width, and 1455mm in height, with a wheelbase of 2700mm. The dimensions of the Corolla are 4620mm in length, 1775mm in width, and 1480mm in height, with a wheelbase of 2700mm.
9
0
Share

What are the symptoms of the brake failure in Dongfeng Kia K3?

Dongfeng Kia K3 exhibits the following symptoms when experiencing brake failure: 1. The brake pedal does not rise when pressed, and there is no resistance. Possible causes: lack of brake fluid, leakage in the brake cylinder, pipelines, or joints, or damage to the master cylinder or sub-cylinder components. 2. Poor braking effect even when the brake pedal is fully depressed, with no improvement in continuous braking and the pedal gradually rising. Possible cause: air mixed in the brake system. 3. The brake pedal rises when continuously pressed, with some improvement in braking effect. Possible cause: excessive gap between the friction pads and brake drum. 4. The brake pedal rises when continuously pressed, accompanied by a sinking feeling. Possible causes: oil leakage or overheating of the brake disc. The Dongfeng Kia K3 is the third K-series model introduced by Dongfeng Yueda Kia, with body dimensions of 4600mm in length, 1780mm in width, and 1445mm in height.
7
2
Share

How much engine oil does the Prado 3.5 require?

The Prado 3.5 requires 7L of engine oil. Engine oil selection: Naturally aspirated engines have relatively basic requirements for oil quality and can use mineral oil or semi-synthetic oil. If the owner has a higher budget, fully synthetic oil can be used. Compared to naturally aspirated engines, turbocharged engines have a more compact structure and operate under harsher conditions, requiring higher-performance oil with better fluidity. Fully synthetic oil is recommended for such engines. Brand selection: For lubricant brands, if oil longevity is a priority, Mobil lubricants can be chosen; if engine cleaning capability is important, Shell oil is recommended; for strong oil film toughness, Castrol can be selected. For example, turbocharged engines are prone to carbon buildup during high-speed operation, so Shell oil with strong cleaning capabilities is a suitable choice.
3
0
Share

What is the reason for the BMW 320's right low beam light having no power?

The BMW 320's right low beam light having no power is caused by a battery fault. H7 bulb specifications: The power of an H7 bulb is typically 55W, 65W, or 80W, with an operating voltage of 12V, a color temperature of 3200K, emitting a yellow-white light, and a illumination range of 50-80 meters. During installation, it has two terminals: one connects to the power supply, and the other connects to the ground. Usage environment for low beam lights: When driving in areas without streetlights at night, or during dusk when it's dark or at dawn when light is just appearing, the low beam lights must be turned on; if encountering heavy fog, snow, or heavy rain where visibility is obstructed, the low beam lights must also be turned on; in some areas where there is lighting but the brightness is insufficient, the low beam lights should also be turned on.
16
5
Share

What is the size of the wiper rubber strip for the Refine M3?

The wiper rubber strip size for the Refine M3 is 17 inches and 26 inches. Wiper rubber strips have a certain service life. After exposure to wind, sun, and rain erosion, they may harden, crack, or peel. Therefore, it is necessary to regularly inspect the wiper rubber strips and replace them when necessary. The Refine M3 is a compact MPV under JAC Motors, with body dimensions of 4645mm in length, 1740mm in width, and 1900mm in height, and a wheelbase of 2810mm. In terms of appearance, the front face of the Refine M3 adopts a classic three-section design with well-proportioned upper and lower detail features. At the same time, the side contour feature line runs through the front face, enhancing the overall sense of the body. Popular elements such as smoked headlights and wing-shaped chrome trim strips also effectively elevate the visual sense of grade.
2
4
Share

What Causes the Key Light to Flash on the Corolla Dashboard?

The key light flashing on the Corolla dashboard is caused by the activation of the engine immobilizer system. Reasons for the key light flashing: If the green key light on the dashboard is flashing and the engine won't start, it's because Honda's anti-theft function has been activated, preventing the vehicle from starting. Solutions for the key light flashing: If the key light on the dashboard is flashing, it means the 'engine chip' inside the key has not been detected. You can try opening the main key to check if there are any abnormalities in the glass tube-shaped engine chip inside and try changing the orientation of the chip. If no abnormalities are found but the engine still won't start, you may need to get a suitable engine chip matched and installed inside the key to start the vehicle. Alternatively, you can consult a professional automotive locksmith to disable the vehicle's immobilizer system using specialized equipment, followed by reprogramming and rematching. Another option is to contact a 4S dealership to disable the anti-theft system and reset the password.
17
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.