Where is the cabin air filter of Senova X35 located?

2 Answers
Allison
07/24/25 3:42am
The cabin air filter of Senova X35 is located behind the glove box on the passenger side. It should be replaced every 10,000 kilometers. If the air environment is particularly poor, it is recommended to replace it earlier. The car cabin air filter is a specialized filter used for air purification inside the vehicle compartment. The Senova X35 is an SUV under the Senova brand of Beijing Automotive Group, equipped with a 1.5L engine, delivering a maximum power of 116 horsepower and a peak torque of 148 Nm. The vehicle measures 4300mm in length, 1815mm in width, and 1640mm in height, with a wheelbase of 2570mm.
Was this review help?
5
2
Share
Dylan
08/10/25 11:13pm
I remember researching the location of the Saab X35's cabin air filter before—it's hidden under the footwell area on the passenger side, usually requiring glove compartment removal. First, empty the glove box since clutter can block access, then locate the plastic clips. Some models need a gentle press or a bit of finesse to release—never force it to avoid damaging the interior. Once open, you’ll spot a small rectangular cover; unscrew or unclip it to pull out the old filter and slot in the new one. I check mine every six months, as AC systems accumulate dust over time, especially in dusty northern regions. Replacing it ensures fresher cabin air, a more comfortable drive, and allergy prevention. These filters are affordable, and DIY replacement saves time and money—just buy the correct model online and ensure the arrow points in the airflow direction.
Was this review help?
12
3
Share
Expand All
More Forum Discussions

What to do if one hole of the ABS pump is not discharging oil?

If one hole of the ABS pump is not discharging oil, the ABS pump needs to be replaced. The following is relevant information about ABS: 1. Description: The ABS electronic control unit is very sensitive to overvoltage and static electricity. Carelessness can damage the chips in the electronic control unit, causing the entire ABS system to fail. Therefore, do not plug or unplug the connector on the electronic control unit when the ignition switch is on. Before performing electric welding on the vehicle, wear an anti-static device (you can also wrap one end of a wire around your wrist and the other end around the vehicle body), unplug the connector on the electronic control unit, and then perform the welding. When charging the battery specially, remove the battery from the vehicle or disconnect the battery cables before charging. 2. Usage precautions: During ABS braking, the rapid retraction and extension of the brake wheel cylinder will frequently compress the high-pressure brake fluid, producing significant noise, and the brake pedal may vibrate and push back against the foot. Do not be troubled by this phenomenon while driving. In emergency situations, use ABS braking without hesitation, press the brake pedal firmly all the way down, and do not release it.
1
1
Share

How many liters of transmission fluid does the Mercedes-Benz C200L require?

For the Mercedes-Benz C200L, the manual transmission fluid replacement capacity is 7L, while the machine replacement capacity is 10L. The recommended replacement interval is every 60,000 kilometers. Below are the methods for replacing the transmission fluid in the Mercedes-Benz C200L: 1. Gravity Drain Method: The method and principle are similar to engine oil replacement. Not all transmission fluid can be drained due to mechanical structures with dead corners such as recesses and uneven surfaces. 2. Machine Flush Method: New transmission fluid is stored inside the flushing machine, which is connected to the transmission via pipes. The new fluid pushes out the old fluid under the machine's operation, resulting in a cleaner fluid circuit. The more new transmission fluid used in the machine flush, the more thoroughly the old fluid is removed. This method typically consumes about 10-15L of fluid and takes approximately 1 hour. 3. Oil Pan Removal Method: This is a root-cleaning approach that also allows for cleaning the fluid filter. Removing the oil pan is a significant task, and the corresponding labor cost will be higher.
4
4
Share

Is It Normal for the Steering Wheel to Be Slightly Off-Center When Driving Straight?

It is normal for the steering wheel to be slightly off-center when driving straight. A car pulling to one side does not necessarily mean the steering wheel is misaligned, and a misaligned steering wheel does not always indicate the car is pulling to one side. Overall, this is not a major issue, though it may feel awkward to handle. Below are some related details: 1. The steering wheel can be adjusted: If the steering wheel is only slightly misaligned (within 20 degrees), it can be corrected by adjusting the tie rods. However, it is important to note that attempting this adjustment yourself carries risks and may lead to more serious issues, so proceed with caution. 2. Method for adjusting the steering wheel: Adjusting the length of the tie rods does not require "cutting" or "extending" them but rather involves "screwing in" or "screwing out" the tie rod base. First, prepare a wrench, then turn the steering wheel fully to the right to expose the rear of the left front wheel. Loosen the fastening nut with the wrench, then rotate the left tie rod clockwise (clockwise rotation shortens the tie rod relative to its base). Next, repeat the steps by turning the steering wheel fully to the left to expose the rear of the right front wheel. Similarly, loosen the fastening nut with the wrench, then rotate the right tie rod counterclockwise (counterclockwise rotation lengthens the tie rod). 3. Adjustment precautions: If the left tie rod is screwed in by one full turn, the right tie rod must also be screwed out by one full turn to ensure equal adjustment on both sides. If the steering wheel is misaligned to the right, the opposite adjustment is required—i.e., the left tie rod is screwed out by one turn, and the right tie rod is screwed in by one turn. Of course, the amount of rotation must be carefully controlled.
15
2
Share

Does motorcycle impoundment affect a C1 driver's license?

If you are caught driving a motorcycle with a C1 driver's license, your license will be revoked. If you already hold a motor vehicle driver's license and wish to apply for an additional permitted vehicle type, you must not have accumulated 12 penalty points in the current scoring cycle or the most recent scoring cycle before the application. To apply for additional permitted vehicle types such as medium-sized buses or tractors, the following regulations must be met: 1. Regulation 1: To apply for a medium-sized bus permit, you must have held a license for driving city buses, large trucks, small cars, small automatic transmission cars, low-speed trucks, or three-wheeled vehicles for at least three years, and must not have accumulated 12 penalty points in the three most recent consecutive scoring cycles before the application. 2. Regulation 2: To apply for a tractor permit, you must have held a license for driving medium-sized buses or large trucks for at least three years, or have held a license for driving large buses for at least one year, and must not have accumulated 12 penalty points in the three most recent consecutive scoring cycles before the application.
6
2
Share

Where is the fuse reference table located for the 2015 Lavida?

The fuse reference table is located inside the fuse box. There are two reference tables in total. The 2015 Lavida model has 54 fuses. If any issues arise with the vehicle, it is necessary to replace the fuses according to the reference table and then check the condition of other sensors. Below is relevant information about the Lavida: 1. Engine: The 2021 model is equipped with 1.2T turbocharged, 1.4T turbocharged, and 1.5L naturally aspirated engines, paired with automatic transmission, manual transmission, and dry dual-clutch transmission respectively. It uses a front-wheel-drive system and comes in both hatchback and sedan body styles. 2. Body Dimensions: The Lavida has a body length of 4670 mm, width of 1806 mm, height of 1474 mm, and a wheelbase of 2688 mm. It is a 4-door, 5-seater model with a fuel tank capacity of 51 liters. The curb weight ranges from 1225 kg to 1265 kg, and the trunk capacity is 510 liters.
14
2
Share

What Could Be the Reason for No Response from Motorcycle Electronic Ignition?

Possible reasons for no response from motorcycle electronic ignition include: insufficient battery power; excessive spark plug gap or carbon buildup; faulty high-voltage cap connected to the spark plug; damaged starter fuse. Below are the inspection methods: 1. Method One: Check whether the cylinder pressure is normal. If there is no compression ratio in the cylinder, it might be due to bent valves that fail to seal properly, resulting in no cylinder pressure and failure to start. If the cylinder pressure is normal, check if the engine rotates tightly. If it does, there could be numerous potential issues, such as cylinder sticking, damaged or detached internal engine components, etc. 2. Method Two: Check if the spark plug receives sufficiently strong high-voltage electricity, whether the valve timing is correct, if there is normal gasoline in the carburetor, if the carburetor is clogged, if there is any air leakage in the intake pipe, and if the air filter and exhaust pipe are blocked.
10
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.