Where is the cabin air filter located in the Teana?

1 Answers
OJason
07/25/25 4:18pm
The cabin air filter of the Teana is located beneath the glove compartment on the passenger side. Below are the relevant details: 1. Steps to remove the cabin air filter: (1) Use a plastic pry tool to remove the cover panel next to the glove compartment. (2) Use a T20 wrench to remove the 3 screws inside the glove compartment, followed by the 3 screws underneath the exterior of the glove compartment. (3) Pull the entire glove compartment outward with force to separate it from the lighting fixture. (4) Unclip the fasteners on the air intake to remove the cabin air filter. 2. The Teana is a flagship mid-to-high-end luxury sedan under the NISSAN brand, equipped with two engine options: a 2.0L inline 4-cylinder naturally aspirated engine paired with a CVT transmission, delivering a maximum power of 117kW and a peak torque of 208Nm; and a 2.0T inline 4-cylinder turbocharged engine paired with a CVT transmission, producing a maximum power of 185kW and a peak torque of 380Nm.
Was this review help?
5
4
Share
More Forum Discussions

What Causes the Engine Warning Light to Illuminate in a Mazda6?

Mazda6 engine warning light illumination causes: When the vehicle's engine warning light is on, a specialized diagnostic scanner must be used to retrieve fault codes before further troubleshooting can proceed. Potential causes include poor air-fuel mixture combustion, sensor malfunctions, maintenance issues, and fuel quality problems. An engine is a machine capable of converting other forms of energy into mechanical energy, encompassing internal combustion engines, external combustion engines, jet engines, electric motors, etc. The Mazda6 measures 4900mm in length, 1880mm in width, and 1420mm in height, with a wheelbase of 2850mm, featuring front-wheel drive configuration.
2
0
Share

How to Replace the Key Battery for Mazda6?

Steps to replace the key battery for Mazda6: 1. First open the key head and separate the key; 2. After separation, use a screwdriver to pry open both sides of the rear half, then you can see the battery; 3. Remove the old battery and install the new one; 4. After replacement, reassemble in the original order. The Mazda6 is a mid-to-high-end sedan with dimensions of 4670mm in length, 1780mm in width, and 1435mm in height, and a wheelbase of 2675mm. The Mazda6 features front-wheel drive, with a high-mounted double-wishbone independent front suspension and an E-type multi-link rear suspension.
19
0
Share

What is the brand of the Mazda CX4 transmission?

Mazda CX4's transmission brand is Mazda's own. The transmission used in the Mazda CX4 is the Skyactiv transmission, with the model number AF406 (AWTF80S). The transmission in the Mazda CX4 is originally imported, and there are two types of transmissions used: one is a 6-speed manual transmission, and the other is a 6-speed automatic manual transmission. Typically, the automatic manual transmission refers to an AT transmission with a manual mode. The Mazda CX4 is equipped with a 2.0L or 2.5L naturally aspirated engine, a six-speed manual transmission, or a six-speed automatic manual transmission. In terms of body dimensions, the Mazda CX4 measures 4637mm in length, 1855mm in width, and 1524mm in height.
11
4
Share

What is the Feidai brand car?

Feidai is a Chinese independent automobile brand headquartered in Zhejiang Province, primarily manufacturing commercial vehicles, special-purpose vehicles, and new energy vehicles. The Feidai model is a microvan pure electric vehicle with dimensions of 4455mm in length, 1640mm in width, and 1970mm in height, featuring a wheelbase of 2870mm and front/rear tire specifications of 185/65R15. It is equipped with a single-speed transmission for electric vehicles, utilizing lithium iron phosphate batteries and a fixed gear ratio transmission. For suspension, this vehicle adopts MacPherson strut independent suspension at the front and leaf spring non-independent suspension at the rear.
20
5
Share

How to Solve the Problem of Tail Lights Staying On?

Solutions for tail lights staying on: The issue of tail lights staying on may be caused by a damaged brake light switch on the brake pedal or a short circuit in the brake light wiring. Remove the protective panel located above the brake, clutch, and accelerator to expose the brake light switch. Rotate the faulty switch counterclockwise to remove it, then replace it with a new brake light switch. Car tail lights include the lamps and bulbs at the rear of the vehicle. The function of the lamps is to gather and emit the light from the bulbs, thereby enhancing the brightness and range of the light emitted. Car tail lights consist of turn signals, brake lights, position lights, rear fog lights, reverse lights, and parking lights. Among these, the turn signals and brake lights are symmetrical, with one on each side.
20
3
Share

Are there any tips for driving at night?

Tips for driving at night: 1. It is necessary to control the speed reasonably, use the car lights flexibly and appropriately, maintain a proper following distance from the vehicle ahead, and avoid frequent overtaking when visibility is not as good at night; 2. When driving on the highway at night, high beams should be used because highways are not equipped with street lights, and vehicles on highways travel at high speeds. Some drivers may not react in time to emergencies. High beams provide strong light, which helps drivers react promptly. Highways have median barriers, so there is no direct contact with oncoming vehicles, eliminating the need to worry too much about them. Moreover, using high beams helps drivers better observe the condition of vehicles ahead. Night driving can be tiring, so when driving on highways at night, the speed should not be too fast, but it should also not be lower than 80 kilometers per hour.
16
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.