Where is the cabin air filter located in the Phaeton?

2 Answers
MacKai
07/29/25 5:30am
The cabin air filter in the Phaeton is located under the hood, near the windshield. To replace it, remove the plastic casing covering the filter, install the new filter, and then reattach the casing. The Phaeton is an imported large luxury sedan under the Volkswagen brand. In terms of body dimensions, it measures 5197 mm in length, 1903 mm in width, and 1450 mm in height, with a wheelbase of 3001 mm. Regarding powertrain, the Phaeton is equipped with six different engines in total. The top-tier model features a 6.0-liter W12 naturally aspirated engine, delivering 450 horsepower and a maximum torque of 560 Nm. The engine reaches its peak power at 6050 rpm, incorporates direct fuel injection technology, and utilizes an aluminum alloy cylinder head and block.
Was this review help?
11
3
Share
DelTucker
08/12/25 9:04am
I regularly maintain my Phaeton, and the location of the cabin air filter is behind the glove compartment on the passenger side. You need to remove the entire glove compartment to access it. Remember, the glove compartment is usually secured by several clips—just press them gently to release, and avoid pulling hard to prevent damaging the parts. This design is quite clever. After replacing the filter, the air from the AC becomes much cleaner, especially when driving in cities with poor air quality—it feels refreshing to breathe. I check it every 12,000 kilometers or so. Excessive dust buildup not only affects cooling but can also breed mold, leading to unpleasant odors. If you're handy, you can easily do it yourself. When choosing a filter, prioritize OEM parts—they're durable and cost-effective.
Was this review help?
12
5
Share
Expand All
More Forum Discussions

Can a car be used without baking after painting?

It is possible for a car to dry naturally after painting without baking, but it takes more than 3 days in good weather to be usable. Characteristics of manual baking paint: Traditional car baking paint is semi-mechanized by hand. Firstly, the work efficiency is not high, the workflow of manual baking paint is complex, the technical level of personnel is required to be high, the consumption is large, the quality of baking paint is difficult to guarantee, and accidents occur frequently. Painting process: When painting, the external air is filtered by the primary filter screen and then sent to the roof by the fan, and then enters the room after secondary filtration and purification by the top filter screen. The working principle of baking paint is different: Baking paint is an industrial paint, which is divided into water-based metallic paint and oil-based metallic paint. Water-based metallic paint is an environmentally friendly coating with water as the solvent, and oil-based metallic paint is with organic solvent as the solvent. The method is to grind the material a little rough and spray some paint.
6
2
Share

What is the difference between non-standard oil and national standard oil?

The differences between non-standard oil and national standard oil are as follows: Density: The density range of national standard diesel is 0.810~0.855, varying with different models. Non-standard diesel certainly cannot meet such standards. Compared with regular diesel, apart from not meeting the standards, there is also the issue of price. Since it is non-standard, the price is significantly lower, and the combustion state is also different. Non-standard oil refers to blended oil that is not produced by regular refineries and fails to meet the national standards for clean gasoline and diesel. Its sources mainly include some individual gas stations that directly blend it with chemical raw materials such as naphtha, aromatics, and MTBE. Hazards: Non-standard diesel causes knocking in diesel vehicles, leading to severe mechanical wear, as well as difficulties in cold starts, increased fuel consumption, and black smoke emissions. It also generates deposits and gum, clogging car filters, forming a large amount of carbon deposits in the combustion chamber, causing piston sticking and increased wear.
10
5
Share

Can a spare tire be used temporarily for a few days?

Generally, a spare tire should not be used for more than three days on the road. For non-full-size spare tires, the total mileage should not exceed 50 kilometers. Definition of a spare tire: A spare tire is an extra tire prepared for a car. In case of a flat tire or any issue with a wheel, the spare tire can be promptly used as a replacement to prevent the car from breaking down midway. Types of spare tires: Full-size spare tire. A full-size spare tire has the exact same specifications as the other four tires on the car and can replace any temporarily or permanently unusable tire. Non-full-size spare tire. This type of spare tire has a slightly smaller diameter and width compared to the other four tires, making it suitable only for temporary use. It should only be used on non-driving wheels, and the maximum speed should not exceed 80 km/h. Run-flat tire. Also known as a safety tire (run-flat tire), commonly referred to as a "bulletproof tire," it is directly translated in the industry as a "tire that can run without air."
1
4
Share

How often should the brake fluid be replaced in an Audi A3

Audi A3 brake fluid should be replaced every 2 years or 40,000 kilometers. It is recommended to use the original FAW-Volkswagen brand. The method for replacing brake fluid in an Audi A3 is as follows: 1. Connect and tighten the interface of the brake fluid replacement device to the vehicle's brake fluid reservoir, then turn on the power of the replacement device; 2. Lift the vehicle using a lift; 3. Loosen the screw of the brake fluid drain port and attach a rubber hose; 4. The process for replacing brake fluid in the front wheels is the same as for the rear wheels. The Audi A3 is a compact car under FAW-Volkswagen. Taking the 2021 Audi A3 Sportback 35TFSI Progressive Elegance model as an example, its dimensions are 4343mm in length, 1815mm in width, and 1458mm in height, with a wheelbase of 2630mm. The body structure is a 5-door, 5-seat hatchback, with a fuel tank capacity of 51 liters and a curb weight of 1400kg.
19
3
Share

What are the contents of the driver's license test?

The driver's license test includes Subject 1, Subject 2, Subject 3, and Subject 4. The following is relevant information: Subject 1 requirements: For first-time applicants for a motor vehicle driver's license or those applying to add a permitted vehicle type, after passing the Subject 1 test, the vehicle management office should issue a driving skill test permit within one day. The driving skill test permit is valid for three years, and the applicant must complete the Subject 2 and Subject 3 tests within the validity period. If the tests are not completed within the validity period, the passed subjects will be invalidated. Retake: Each subject test can be taken once, and those who fail can retake once. If the retake is not taken or the retake is still failed, the current test is terminated, and the applicant must reschedule the test, but the Subject 2 and Subject 3 tests should be scheduled after ten days. If the Subject 3 safe and civilized driving knowledge test is failed, the passed road driving skill test results remain valid.
1
1
Share

What is the size of a driver's license photo?

The photo for a car driver's license should be a one-inch white background. Here is the relevant information: Requirements for motor vehicle driver's license photos: The photo must be taken within 6 months before the applicant applies for the driver's license. The photo should be a straight-edged, front-facing, color, bareheaded, single-person half-length ID photo without a hat, scarf, uniform, or colored glasses. For those with long hair, both ears should be visible, and the head or face should not have any tilting, turning, heavy makeup, or accessories that affect facial feature recognition. The background color should be white, the portrait should be clear, with rich layers and natural expression, without obvious distortion. The photo size should be 32mm×22mm, with a head width of 14mm~16mm and a head length of 19mm~22mm. Requirements for the electronic photo information: The photo must be larger than 50KB and smaller than 1MB in jpg format, with a resolution of ≥300dpi; electronic files cannot be scanned or rephotographed; the electronic photo information of the driver must meet the standard size.
7
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.